similar to: Sipura 2000 vs 2100

Hi Friends, I have successfully implemented Intercom, Voicemail and International dialing using Asterisk. Now I want to connect my PSTN Lines to Asterisk server. I have 3 PSTN number (lines) to connect to Asterisk. For this, I want to use Sipura SPA-2100. Is my decession is correct or not? Is there any disadvantages with this Sipura SPA-2100? Please tell me. Thank you. Regards, Chandramouli

I am wondering if anyone has sample XML config for the Sipura 2100 ATA. We have been autoprovisioning our 2002s with success and the 2100's take the same XML that we have come up with, but I am not sure of the syntax for specific things that I need these boxes to do, such as turning T.38 on. If anyone is willing to share their xml for autoprovisioning Sipura 2100's, it would be much

I have an analog phone connected to a Sipura 2100 which in turn connecteds to * over a 100mbps LAN. When I do ChanSpy on a bridged call, it causes massive jitter. When I attempt ChanSpy with a Grandstream GXP-2000 the monitored call is clear. Has anyone had this happen? Any suggestions? ScriptHead

I know the subject of faxing has been covered in some detail, but I was wondering if anyone has a hardware configuration similar to ours that has faxes working successfully and would be willing to share any settings/insight. We are unable to fax reliably with a Sipura 2100 connected to Asterisk. We do not route calls over the Internet and our network has very low latency. The Asterisk

I found a thread [1] last month about the poor/crappy g729 quality on Sipura units. Anyone noticed an improvement or the quality is still poor? If the Sipura firmware/g729 offers no quality yet, who else is offering a dual channel g729 ATA? I heard about Uniden, but I have no "reports" about their ATA... [1] Sipura g729 call quality to PSTN

Should a Linksys Sipura 2102 be configured with nat=yes even if it is on the local network? I have been having some troubles with a Linksys Sipura 2100 series, which suffers from NO AUDIO after a few calls.. Because it is on the same subnet as Asterisk it is configured with nat=no. When you think of it because the Sipura 2100 is a broadband router, the voice part may be considered as being behind

If this has been covered before - I appologize. We use some Sipura SPA-2000's with the g711 codec and all seems fine (except for the occasional failure to register errors in my asterisk logs - but I will save that for another post). g711 call quality is on par with our Cisco 7960's. However, when using the g729 codec, the call quality on the Sipura device goes downhill on the PSTN side

Hi all, i need sample xml configuration files for linksys pap2, linksys pap-2t, sipura 2100, sipura 2102, 1001, 3000 and 3102. All of these are linksys/sipura products. So if anyone has these sample files then plz share. -- Best Regards Rizwan Hisham Software Engineer Axvoice Inc. www.axvoice.com -------------- next part -------------- An HTML attachment was scrubbed... URL:

I've just made an interesting observation that I'd like to share with you all: the popular Sipura SPA-2100 just doesn't seem to be as great as I'd hoped. I've been trying to get inbound AND outbound faxing working via Asterisk and at least one of my termination services: Voicepulse or Sixtel. In general, inbound has been working flawlessly but outbound has been pretty

Voxilla news story: http://voxilla.com/voxstory84-nested-order0-threshold0.html Two new products * A Sipura 2000 in a linksys box: Linksys PAP2 Phone Adapter * A combination NAT router with 2 FXS ports: Linksys RT31P2 Broadband Router Jim James H. Thompson jht@lava.net

Hi, I have an older phone with touch screen from Philips. It have it connected to Sipura 3000 FXS port and majority of features work ok. But phone also has touchscreen and web browser that I'd love to use for accessing my local web pages. But the phone only allows me to setup ISP phone number (username and password) and it wants to call it to get to Internet. Since it is connected to

I just bough a Sipura SPA-2100 to use with Asterisk. When I use the analog handset plugged into the SPA-2100, the person on the other end can hardly hear me. I check the SPA-2100 setup and their is no mic/spk gain control. Is this a problem with the SPA-2100 or with Asterisk? Any way for asterisk to compensate for the poor audio level (if the problem is the SPA-2100)? Thanks, Mike

Hi, I'm trying to configure Sipura 2000 (behind NAT) which connects to Asterisk (public IP, no NAT) and having interesting results. When Sipura is behind Linux/NAT firewall it works great and no special NAT settings on Sipura are necessary. The issue I'm having is when Sipura is behind Linksys broadband NAT router. Sipura gets registered with Asterisk just fine, but I can't hear

Hi, I'm looking for a full list of xml provisioning variables of the SPA-2100/3000. Currently the Sipura website has example XMLs only for the SPA-841 [1] and SPA-941 [2]. I'm mostly interested in the CallerID type selector variables and whatever variables control the PSTN<->VoIP settings. Sipura Configuration website form field names are numeral only. :( [1]

I have been trying to read everything I can find on Sipura 2000 and Asterisk. I am trying to make the Sipura-2000 act as two analog lines off my asterisk. I have followed (what I believe) the example on http://www.voxilla.com/Article39.phtml and I still can't get my Sipura to register with my Asterisk server. I can re-config my Sipura to talk to fwd, or voice-pulse connect and it works

I've been beating my head for 5 hours to figure out why my asterisk server or sipura isn't passing my voice over to the caller. It seems i can hear the caller but they can't hear me it seems either the asterisk or the sipura isn't passing this information. Here's my setup specs asterisk server 0.7.1 - X100P Card - Sipura 2000 - Nufone Service - Voicepulse

I recently purchased a Sipura 2000 and connected a phone to it which is connected to my asterisk box via sip. Calls to the Sipura 2000 work fine from another sip device connected through *, from either an fxo or fxs (via adtran channel bank connected to a T400P card) port. However, when a call comes in from the phone company over a T1 with em_w trunks, the phone on the Sipura will ring but I

Hello all, I am trying to find out if anyone has a provider that is good with dtmf playback using a Sipura 2100? I've just dialed with voxee and the call goes through but when I press 1 my dialer does not " hear" it. My dialer is making the call using a Dialogic d/4PCI connected to the Sipura 2100 through voxee and I am calling my landline. When I pick up the landline

I'm really trying to understand this. I have a Sipura 2000, brother MFC, and SpanDSP set up on asterisk. because asterisk softfax was not working well, i set up faxes to goto line2 on the sipura. this is working fine, i have only tested a few short faxes, but already my completion rate was 100% vs 5-10% that spandsp and asterisk gave me. here's the odd part. using the fax machine, I

Hello all ! Can anyone recommend me ATA device that REALLY has T.38 built in. So far I have heard of Telco Systems Access201, which seems to be impossible to bye in Europe (all resselers are droped Telco systems ATAs for some reason (tried in Germany and in UK so far)), and I have heard that SIPURA SPA-2100 should have T.38 built in into newer firmware, but I wasn't able to confirm that