similar to: Read() timeout hangs up the line

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

dear Hackers, i have a voicetronix Openswitch card, and i have been finding it very dificult to get it to work with asterisk. i intend to connect 8 ports to the PSTN and 4 as station ports. problem 1: On running asterisk all i get at first i get : event[9=>[11] station OFF hook] on vpb/1-12 even [12=>[11] loop drop on vpb/1-12 event [12=>[11] Tone detect:GRUNT event [2=>[11] Dial

When dialling in and dialling my extension, when answered I get " Read_channel ## vpb/1-3: Setting record mode, bridge = 0 WARNING[20499]: File chan_sip.c, Line 1111 (sip_write): Asked to transmit frame type 8, while native formats is 4 (read/write = 4/4) == Spawn extension (default, 1004, 1) exited non-zero on 'vpb/1-3' -- hangup on vpb (vpb/1-3) -- Hungup on vpb/1-3 complete --

hi there, i've been able to successfully run asterisk with the Voicetronix OpenLine4 card, it can accept calls and function normally. The only problem I'm experiencing so far is getting the card to outdial to a third party. What I'm trying to achieve is basically call bridging, where the caller dials in to asterisk, some IVR plays and then attempts to perform a "transfer"

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

Hi there, I am trying to delay sending out DTMF from Voicetronix OpenLine4 to the CO line. The reason being is that Voicetronix sends out the DTMF too fast even before the line is fully established with the carrier. Usually when dialing an 8 digit number, only 7 digits are actually successfully heard by the carrier. Currently, my dial plan is: exten => _9.,1,Dial(vpb/1-1/${EXTEN:1}) Daniel

Hello, I'm trying to figure out how to change the redial, thus far if I hit redial it will redial the last called I made that was answered, not the last call I made that was not answer. I'm using Asterisk 1.8 Thanks, Motty

Hello, Hacker I install VoiceTronix OpenSwitch 12 port PCI Telephone Card, and setting vpb.conf, extensions.conf following My problem is: When i dial to fxo(channel 9-12), it is ok, but when i continue press exten 102, the channel crach with error messages following exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872 Do i ignore some setting for VoiceTronix OpenSwitch12

Hi all, We are looking at VoIP over Wifi and I was wondering if anybody had any ideas around automatically transfering calls after an RTP timeout? The idea is this: a user is on a call with their IP phone and the connection drops (e.g. user walks out of range of their Wifi AP). Using RTP timeout I was hoping rather than just dropping the call I could keep the other party on hold whilst

Hi, What is the best way to implement Automatic Redial on No Answer ? Looking at http://www.ietf.org/internet-drafts/draft-ietf-sipping-service-examples-12.txtI can see how Automatic Redial on Busy could (should) be done. How would you do it on No Answer ? Is there any event you should SUBSCRIBE to so that you're notified that you're callee is available ? What if you ask to be notified

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Deutsche ?bersetzung folgt / German version following ===================================================== Hello, i have Asterisk running with 2 ISDN-Cards. One AVM Fritz for connection to german ISDN and one HFC-compatible-Card (NT mode) for connection to ISDN-Phone (later: ISDN-PBX). Here is my actual installation: ISDN -> Fritz - ASTERISK ? HFC-NT <- ISDN-Telephone If i pick up my

Hi all, I have an external application commanding asterisk by AMI and AsyncAGI. I also have a dialplan like this: ; AsyncAGI extensions exten => _8.,1,Noop(entering in AGI loop at 8 ${EXTEN}); exten => _8.,n,AGI(agi:async); exten => _8.,n,Hangup(); ; Meetme extensions exten => _1.,1,Noop(Conference ${EXTEN} ${CONTEXT}); exten =>

I am a serious Asterisk newbie: just installed asterisk last week and it is now running with our Voicetronix OpenLine4 hardware. All is working as expected with one exception, in the following sequence (extracted from my extensions.conf file): [GetConfirmation] exten => s,n,SetVar(TimeOut=0) ; if timeout and TimeOut=1 then user already timed out once, so hangup exten =>

I have an asterisk box and SIP / IAX2 phones. To call out, users have to add 0 (zero) before a real telephone number. That means, that if they want to call someone that has a number 123456, they have to call 0-123456. Simple, right? This has a serious drawback though - when someone calls us from the number 123456, we see the callerID 123456, and we're unable to use the callback/redial

Any guidance on how to get my openline4 to get recognized by asterisk@home? I've got my vpb drivers running, but not sure how to add it as a trunk, should it be via zap? or is there another way? Thanks, Chuck

Good day all I added the music on hold entry in vpb.conf and commented out default line in musiconhold.conf. Asterisk starts up with the default mp3 but as soon as I remove it and add my mp3 it just doenst start up and gives a broken pipe error? Please Help or advice Thanks ALtus

B.H. Hello, all. We have a dialer software that runs outgoing telephony campaigns. We have been using it successfully with PRI cards, now we're evaluating it's use also with a SIP trunk. Most of the things run perfectly good without a need to change anything except for dial string, but there's some strange problem with asterisk interpreting SIP result codes. Our software is written

Hello, I have to dial prefix 9 for non local numbers however when i missed calls i Can't redial this number because of "9" is not append . I use polycom phones . What Can i do ? Harry __________________________________________________ Do You Yahoo!? En finir avec le spam? Yahoo! Mail vous offre la meilleure protection possible contre les messages non sollicit?s

Hi, I would like to implement an auto-redial function in a context. The idea is about like this: Dial a number Hear busy Hangup Pick up again Dial a code like *123 => jumps into a context which redials until callresult is not busy Maybe like this: [autoredial] exten => s,1,Set(number=${CHANNEL(lastdialed)}) exten => s,2,Dial(SIP/${number}@account,60,g) exten => s,3,Wait(15) exten