similar to: Asterisk with MySQL

My phone still says Not-Registered. I have a Polycom SoundPoint 600 SIP phone. Here is my sip.conf file: ; ; SIP Configuration ; [general] context=default ; Default context for incoming calls port=5060 ;added bindport=5060 ; UDP Port to bind to (SIP standard port is 5060) bindaddr=0.0.0.0 ; IP address to bind to (0.0.0.0 binds to all) srvlookup=yes ;

hi do u have the sip phones extensions in the extension.conf and are they in the right context (sip-incoming)??? are the sip phone registering to asterisk?? try stop asterisk and reconnect as asterisk -vvvvvvvc to check see them registering... ________________________________ From: asterisk-users-bounces@lists.digium.com on behalf of Sistemista WebSolvingJaa Sent: Fri 7/1/2005 6:43 PM

Hi everyone! I'm quite a newbie at this Asterisk stuff so please bear with me. We've recently decided to start training in Asterisk via AsteriskNow! Asterisk version is 1.4.18.1 through AsteriskNow! 1.02 The box we have is paired with a Digium TE110P and we've managed to get it to the point where incoming calls via a single DID (from NTT Japan) can be received and answered

Now that I actually try and google for it, I can't find any dual mode GSM/DECT handsets, only pages telling me that they exist without any actual information!!! Does anyone know of any such handsets? (and even better, ones that are available in Australia) I've searched a few of the major gsm manufacturers (nokia, Panasonic, sonyericsson) but their web sites are absolutely pathetic to the

Hi list, i've problems with my * server and the 4 phones which are linked to it. i've 2 grandstream bt100 with the firmware upgraded to 101, a wi-fi phone (i don't know its brand) and another ip phone i don't know its brand. with this sip.conf : [general] port = 5060 bindaddr = 192.168.100.229 context = default ;x changed from default to sip localnet = 192.168.100.0/24

Thanks to help on this list and Sangoma's support we have incoming and outgoing calls passing through asterisk. However both incoming and outgoing calls are greeted by silence. I've noted our existing config below with our test extensions.conf. Help much appreciated Rory Zaptel ----------------------------------------------------------------------- loadzone=uk defaultzone=uk #Sangoma

Hello guys. I am a fairly new user to Asterisk, and I'm just having a tough time. My goal is to set up a VOIP PBX. I have signed up with a BroadVoice number, and I have three systems with SIP phones. The PBX and the SIP phones are all behind a Cisco PIX running NAT. I am using Asterisk CVS version from yesterday. I also tried 1.0.3 with little luck. The SIP phones are two X-Lites on

Here's a possible bug, or more likely, I'm just missing something. We have a pots card in one of our asterisk boxes. Its a simple asterisk setup with one FXO/FXS card and basic static extensions file, etc. When we dial out over the pots line, 4 out of 5 times, it will work. However, every 4 or 5 times, we get an error back from the provider that says "The number you have dialed.....

It seems that when you use Realtime static and possibly realtime realtime for sip users, that Asterisk fails to create the regexten context for DUNDi. Someone else had the same problem back in July. Doesn't look like they ever had a resolution. <http://lists.digium.com/pipermail/asterisk-users/2006-July/160105.html>

Hi List, we are using openh323 gatekeeper for voip telefony. We also have a voip over ss7 TELES Switch for voip into POSTN Network. Know we want to use Asterisk for converting SIP to h323. Now my question. Is Asterisk an full h323 gatekeeper like openh323? Do we need openh323 GK for astrerisk, too?. And how can i tell asterisk to sent all none SIP-ip calls to the gatekeeper over h323? thx

I've just installed an X100P, built the kernel module, and tried to use it to make an outgoing call (via a phone connected to an ATA-186). However, I just get a reorder tone and see this on the console: -- Executing Dial("SIP/ata1-4409", "Zap/1/5551212") in new stack NOTICE[1200825920]: File app_dial.c, Line 481 (dial_exec): Unable to create channel of type

Hi, I have been trying to workout how to use the call pickup. So Far, I have the following in zapata.conf [channels] signalling => fxo_ks context => local pickupgroup=1 callgroup=1 channel => 1-3 When I dial *8# all I hear is busy tone. What have I missed? thanks Jay.

I have a setup of 3 Cisco 7940 running Sip image 6.3. All these phone are registered by the below information *CLI> sip show peers Name/username Host Mask Port Status 2002/2002 192.168.22.199 (D) 255.255.255.255 5060 Unmonitored 2001/2001 192.168.22.200 (D) 255.255.255.255 5060 Unmonitored 2000/2000 192.168.22.198 (D)

Before I play around with this again in 1.2.1, regexten is still essentially broken, correct? The misconception seems to be that it allows you to execute a command upon registration from a SIP UA. Even the O'Reilly TFOT book erroneously states that this is what it is for. After reading the developer discussion though, it definitely seems to be broken. Is it fixed yet? Doug.

Hi Anyone know how to use regcontext et regexten parameter from sip.conf and can give an example ? thx regards Harry -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20090807/ef9ba45e/attachment.htm

hi, I am new to * and setting up a test system. here my setup : - debian (from knoppix 3.3) - Asterisk 0.7.1 (from the debian package) - AVM Fritz card used with i4l - softphone I use for testing SJphone on windows - I can make great softphone - softphone calls - I can call from an outside line * and get connected to a softphone here my problem: I can not make outbound calls. I place a call

Can anyone help with the use of regexten? (* 1.4.3) I've got Asterisk creating extensions for my SIP phones using regexten but I can't seem to figure out how to make use of them once they're registered. Here's my dialplan for from-sip (the SIP's default context): asterisk*CLI> dialplan show from-sip [ Context 'from-sip' created by 'pbx_config' ]

How do I make a user dial a passcode if he wants to make an international call? ________________________________ This electronic message contains information from BOSH Global Services which may be company sensitive, proprietary, privileged or otherwise protected from disclosure. The information is intended to be used solely by the recipient(s) named above. If you are not an intended recipient,

Hey all, I'm pretty new to Asterisk and VoIP in general, so I'm hoping I can get a bit of help here. First I'll explain my setup, and then my problem. Right now I have a Cisco 3640 with a VIC2FXO card in it which has 2 FXO ports. I have an analog phone line plugged into the first port (voice-port 1/0/0). I've got it setup so that calls coming into that analog line are

Anyone help me here? I am a newbie so be gentle ;-)...... It worked once and then I played with the configs. I have a static IP address which is on my private network.. Phone is 192.192.192.220 and asterisk server is 192.192.192.22 I have the 7690 with a SIP iamge (Whatever latest is ) I have 3 lines setup with Free World Dial up and have the 4th setup to connect to my asterisk server. Here