similar to: Can't initiate a call with X-Lite.

Hi, I've got an Asterisk box with grandstream and xlite clients on it. No here's the thing: - I grey out all the codecs on the Xlite except for GSM - I call the Grandstream from the Xlite, the Xlite uses the GSM codec and the Grandstream uses ulaw, with Asterisk doing the conversion, everything fine - I call the Xlite from the Grandstrea, the Xlite ends up using the ulaw codec as

Is anyone using this combination successfully? I have a dell 500sc running rh9 and asterisk 1.0rc1. It is configured with an x100p. I have a Sipura SPA-2000, laptop with Xlite and a Grandstream Budgetone BT-101. I have signed up with Voipjet (they use iax2). I also have an FWD number via iax2. I can sucessfully call back and forth to all devices via zap, sip, and fwd. I can successfully

Hello, I have a problem with asterisk and Grandstream BudgeTone-100. With default configuration everything works (in anonymous mode and fixed IP), but if Im trying to enable registering, it dos not work. I used 'sip debug' and verbose level 10, nothing happens if I switch telephone on (no messages about bad auth etc). As I understood, after switching phone on at first it will try to

Good evening all. I'm having this strange behavior when dialing two or more simultaneus calls via IAX to other * boxes. Sound starts to have more latency, wich increments until it's almost impossible to talk (6 or more seconds), I try this calling with two grandstreams, one grandstream one tdm410p, one tdm410p and sjphone, sjphone and one grandstream, the result are similar.

X-Lite build 1079 consistently chokes no matter which codec I use - after five seconds I suddenly have no sound coming in and possibly no sound going out too. Putting the line I'm on on hold and then switching back to it gives me another five seconds of sound, then it dies, etc. The Grandstream 101 I'm using is a piece of junk but I don't have the same problem with it. Not sure

hi all, was wondering if someone could assist with a slight problem i'm having. I have asterisk setup with extensions 101 to 109 and am using xlite, grandstream budgetone, polycom ip500 and a couple of other phones. the problem is: 1. only the xlite extension (107) can receive calls. 2. all extensions can dial into voicemail and get mwi when msgs are received. 3. when dialing a non-xlite

Hi all, I'm testing Linksys SPA922 phone and I have strange issue. when call is finished on the phone I see "CallEnded" and normal silence for cca. 5 seconds and then I get fast busy for cca. 20 sec. So, this isn't automatic hangup as on other phones I have tried (Cisco 7940, grandstream, XLite,... ) and I have to manually hangup handset to finish a call. Is this normal behavior

Beginner to Asterisk, but not beginner to VoIP FreePBX front end running on a dell 1550 and XLite running on a different Woindows XP box Both boxes connected via switch on same subnet. No NAT involved On FreePBX I created a new extension 1001 with a SIP password of 1001 On Xlite, username is 1001, password is 1001, authorization user name is 1001, and domain is IP of Free PBX XLite tries to

We are using MFC/R2 driver successfully in at least three places in Brazil. I have problem with an Asterisk integrated with MFC/R2 with a Siemens Hicom 300. I can get a good audio quality with Grandstream, Polycom, and X-Lite softfones, but SIPURAS and Linksys get a garbled audio, something like a "Darth Vader" voice. We have tried everything in Sipura. The SIPURA 2000 and the Linksys

Anyone got any tips on improving sound quality on soft phones running under Window XP SP2? I have tried Xlite, SJPhone and Firefly. They all seem to have significant sound quality problems. We have a reasonable sized network of several hundred devices connected together using Layer 2 switches, i.e. pretty dumb switches with no QoS. I also have a Grandstream connected to the same switching gear.

Hi! I have a new problem with my SIP device.I have done some changes and now I receive continuosly a SIP message: "501" "Not impelmented" back from the SIP Gateway. I can see that it doesn't register to Asterisk. I have in the SIP device: Registrar 1: UnRegistered to: 2222 registrar: 188.208.12.237 5060 expires: 2000 name: gateway passwd: 123 My

I am having problems transferring calls from one sip extension to another - the extensions use various phones hardware/software. From what I can tell I should just be able to press # and then dial an extension to blind xfer a call right? How do I do attended xfer? Either the phones (for this test I have tried xlite and budgetone102) are not sending DTMF correctly or something else is amiss...

Does anyone have X-Lite build 1059 working fully with Asterisk? The GSM Codec works very well now but we have problems when using G711 in that when I setup a ping between the two sites and then watch the latency, it steadily increases and starts at about 150ms and goes up to 2500ms within about 20 seconds. I have not investigated fully but I guess that its sending ever increasing size packets.

Hi, Problem: When talking to someone (from pstn) and this person is not talking loud, the voice is cut by Asterisk. I tried increase RxGain but it changed nothing (was talking louder but voice still cut.) I use XLite as soft phone. I think this is probably a codec setting... but how do I check that on server side? I just don't know what to do. All works fine (asteriskathome) but I always

Hi all, I have my asterisk setup as following: IP 2 x E1 x-lite <-------> Asterisk -------> PSTN When I place a call from x-lite to PSTN, the quality of the sound in the direction x-lite -> PSTN is very bad. That is, the voice of the x-lite user, heard by the PSTN user is choppy and makes communication not very pleasant. The sound is choppy as if bits of data

Hi all, I'm working on an implementation of VoIP en Linux. I have a Debian Suse (*.*.*.173) with an * and a X-lite client and a Red Hat 9.0 (*.*.*.172) with another softphone X-lite. Both of the softphones are registering and appear in the peers (sip show peers) with the good parameters of address and port. If I try to make a call, * receive the INVITE request and send a 404 NOT FOUND answer.

This seems to have been reported before, but I've seen no resolution: http://lists.digium.com/pipermail/asterisk-dev/2003-August/001470.html http://lists.digium.com/pipermail/asterisk-users/2003-August/019091.html http://lists.digium.com/pipermail/asterisk-users/2003-October/024472.html When forcing use of Speex, no sound comes out at all (Speex-1.0.3 on the Asterisk server) When forcing

Just got a headset for testing asterisk and am using X-Lite. I plugged in the headset into the headset jack and is there any way to configure X-lite to use the headset instead of the speakers? Or will I have to plug the headset in the speaker jack ? -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi Everyone, I've got a Cisco 3810 rig with 6 analog FXS ports, and ethernet. I'm wondering in anyone has got one of these suckers to work with asterisk in such a way that each FXS port has it's own extension. It speaks SIP, and I can send calls from asterisk out to it, but can't figure out how to get it to pass username & pw to asterisk when I try to configure it as a

I've been looking at Asterisk for a replacement for our phone system and I'm hoping someone can help validate my assumptions. We have 4 analog lines coming into the building. These lines are simple POT lines and we have them in a "hunt group" with Verizon so that when a single phone number is dialed, the first line is rang, if that line is busy it will ring the second line, and