similar to: Subject: Re: Dial with no phone line connected

I have more FXO ports on TDM400's than I have PSTN lines available for testing. When all the lines were used up (the FXO ports are all in zap group 2), and I did a Dial(Zap/G2/${phone},5) it thinks the Dial succeeded even though there is neither line voltage nor dial tone. Can at least the lack of voltage be detected? It would be good in case one of the phone wires fell out that it would

Ouch, part reset, quickly restoring reality (0) Power alarm on module 1, resetting! I have looked though a lot of email on this issue, and no one seems to have the answer. How many people are seeing this on a TDM400 card? Does anyone have a "REAL" answer to it. Yes, I do have the power connected to it! Regards Garry Taylor

Hi, I am interesting how can I use the capabilities of ProSLIC to measure the following PSTN parameters: - Voltage (V) & Polarity (+-); - Current (A); - Frequency (Hz). Are there any ready for use tools? If there aren't ready for use tools how can I do the above measuring? Best Regards, Miroslav Nachev

Greetings all- During some recent testing and debugging, I wanted to use the 'fxstest' application. However, I found it hasn't been built when doing the standard 'make, make install' shtick with dahdi-linux-complete-2.3.0.1+2.3.0... Can anyone tell me how to build fxstest? Thanks! --Tim

Hi all, I have been looking at the code for both the zaptel driver (wctdm.c/wcfxs.c) and the asterisk channel driver (chan_zap.c) trying to figure out how much of this that has been implemented. So far I can see that the current stable 1.0.9.1 zaptel driver don't have the SETPOLARITY ioctl that would be required to properly signal the Swedish/Dutch CLIP, but the 1.2 beta1 has this

Hi all, I cant ring my phone with fxstest, but all else works (playing tones, stats , regdump). My ring voltage is -53.7680 volts as reported by stats option to fxstest. However, I can ring my phone with Asterisk !!! With fxstest, I just hear a click if I am off hook, and ask it to ring my phone. I am in the UK, and have a ring capacitor installed to the fxs port. Even without that,

Rich Adamson wrote: > How old of code are you looking at? The wcfxs driver was renamed to wctdm > some time ago. Current cvs doesn't include it. I was using zaptel-1.0.0, but I took a look at 1.0.3 and it's still wcfxs there. I'm about to bring this online, would rather stick with releases.

I have a running * with a TDM40B board in it. I have 3 analog phones that works (rings) perfectly when connected to a Telco POTS line. When connected to the Digium TDM40B (with FXS port), I have problems with 'ringing': 1 phone 'ringes' normally 1 phone 'ringes' a bit cripled (instead of ring-ring... ring-ring..., it does 'ring-ri... ri.... ring... ri...) and the 3rd

This is rather bizarre: My TDM11 (one FXS) rings a $10 passive phone with REN of 1.0B, a cheap speaker phone of 0.3B, and a cordless phone with marked REN of 0.0B. But it couldn't properly ring this 27935GE3-B (FCC ID G9H2-7930) cordless phone rated at merely 0.1B. Rarely, the phone will crack out an occasional weak and abrupt beap, but never a normal ring. Otherwise Asterisk and TDM400P

Ahhh this could be my problem! I just checked which wires on the RJ11 cable had a voltage across them and it was the yellow and green (3 & 4?). From what someone posted the other day it's supposed to be Bumble Bee and Christmas Tree. I did have to get a technician out to fix my line when it was first installed because it was dead. Maybe he wired it up incorrectly or maybe they just do it

I have: RedHat 9.0 TDM40B asterisk-0.9.0 compiled from sources zaptel-0.9.1 likewise /etc/zaptel.conf contains fxoks=1-4 loadzone = us defaultzone=us loaded modules zaptel and wcfxs /etc/askterisk/zapata.conf contains [channels] language = en signalling = fxo_ks context = phones channel => 1-4 /etc/askterisk/extensions.conf contains [general]

Canuck15, No, I hadn't played with the gains. But I've now done so and no difference unfortunately. Thanks for the suggestion though. I have discovered that after Asterisk has answered the call and the remote caller has hung up, if I lift the receiver on a phone connected to the line (in parallel with Asterisk), Asterisk then DOES instantly hang up. Would it be reasonable to assume the

Hi: I have a Sangoma A200 card installed in a server with two FXO modules and one FXS module. Analog sets connected to the FXS module have a "squeaky static" -- it's like static mixed with the sound of someone vigorously cleaning a window a few doors down. In other words, it's not a classic static noise, but it is noise, and it's distracting. Remote callers can hear this

Heya all, I'm experiencing some problems with a TDM40P and was wondering if anyone else on this list has similar experiences, or maybe even a possible solution. My setup is a dual PIII-750 with 1 gig of RAM, with an X100P, connected to an analog line to my telco, and a TDM40P with analog phones connected. The TDM-card is not sharing any interrupts, but the X100P is, with the 2 Adaptec SCSI

Hi; I'm trying to connect a TDM400P with an FXS module to a Valcom V-9940 Paging adaptor. This port on the TDM400P was connected to a 2500 Set and was working I just re-connected it to the Valcom (which is known to work on a Telco POTS line) and its not picking up. The Valcom docs say it need a minimum of 75 Volts at 20-30 Hz to recognize a call... So the question is what ring voltage

Hi all, I've struggled for several days trying to get a Digium TDM04B 4-port wxfco card working on a Dell 1U PowerEdge 750 machine running Fedora Core 1. I finally got a call back from Digium who indicated that there is a fundamental conflict between the card and the PowerEdge having to do with PCI interrupts. Asterisk version is stable v1-0 12/29/04. The symptoms of the problem were as

Hi, Thanks for giving me a detailed reply on hardware needs steven. I have been looking at the archives in detail and found a few people have had problems with zaptel compilation on suse(kernel-source-2.4.19.SuSE-342 // gcc 3.2.2 ) ... is shifting to red hat the only viable scenario...would be a pain cuz suse comes with sun java desktop system( just bought it !! ) ... any fixes would be a

Hi Eric, > On 12 avr. 2016, at 17:48, Eric Cooper <ecc at cmu.edu> wrote: > > On Tue, Apr 12, 2016 at 04:36:58PM +0200, Bertrand LUPART - Linkeo.com wrote: >> I just made a asterisk / dahdi fresh install on Debian 8.4, and ended up with the following packages : >> [...] >> However, i can't find any dahdi startup script, neither init.d neither systemd

An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031223/62cf404e/attachment.htm -------------- next part -------------- Hello When I tried loading TDM400P module using insmod command, I get following error messages. Is there some problem with my asterisk installation. Please advise. Thanks Tony $insmod wcfxs Using

I am unable to compile the zaptel drivers on the latest kernel for fc 3, I get the following errors which are listed below if anyone has any suggestions on how I can solve this issue aside from trying a different distro, please don't hesitate to offer. Thanks in advance. [root@asterisk-test2 zaptel]# make linux26 make -C /lib/modules/`uname -r`/build SUBDIRS=/usr/src/zaptel modules make[1]: