similar to: Special Problem in Australia ??

Afternoon all, After doing some test on my asterisk box I can successfully receive calls to my Asterisk PBX to a SIP phone from The Telstra PSTN network Dial out from a sip phone is also not an issue, all calls connect and terminate normally. If I call the Asterisk PBX say from PSTN in Zap1-1 and out through ZAP2-2 back to the PSTN (after entering the correct pin off course) the card does not

Hi All, This isn't really a question, but it's an issue I experienced that was driving me crazy for a few days, so I thought it might be good for the archives. Basically what was happening was everytime a particular customer called (long distance), the line would disconnect immediately after answering. I thought it might have been the phone, so I swapped the phone with another - still

Is anyone having/had a problem with a TDM400P card hanging up on STD outbound calls as soon as the called party answers. I'm guessing that * is responding to the STD pips in some way. -- Howard. LANNet Computing Associates; Your Linux people <http://www.lannetlinux.com> ------------------------------------------ "When you just want a system that works, you choose Linux; when you

I am having problems getting incoming caller id to work on a Telstra Onramp 10. I have changed "/DEFAULT_CIDRINGS 2"/ Is there something i'm missing ? My Cisco 7960 just shows "asterisk" Thanks, Nathan [zapata.conf] context=incoming usecallingpres=yes relaxdtmf=no rxgain=0.0 txgain=0.0 busydetect=no pridialplan=local usecallerid=yes callerid=asreceived

Hi, I am currently trying to find a replacement for a dinosaur PBX and want to replace it with a VoIP solution. We have just moved our lines over to an Optus Multiline from a Telstra ISDN Onramp 30 service with 100 lines. My question for you good people is what sort of hardware do I need to interface Asterix into the Optus Multiline? The Optus service is terminated in my office to a SHDSL

Hello list, I have an X100P clone card, and I've been trying to get it to receive Telstra Caller-ID without any luck. Hence these two questions:- 1) Will a genuine X100P work? 2) If so, where can I get one in Australia? Cheers, Jon

Hi, Just wondering if there are any people out there using the Zaptel Wildcard E1 interfaces on Telstra PRI?s in Australia. If so, is anyone happy to share their config? Thanks, Phil --- Outgoing mail is certified Virus Free. Checked by AVG anti-virus system (http://www.grisoft.com). Version: 6.0.510 / Virus Database: 307 - Release Date: 14/08/2003

Hai, As I know i could open my shares via domain eg: \\domainc.com\share I have 2 samba 4.1.5 server and one win2003 DC. Succesfully made a clustered filesystem so now both servers (except win2003) can open the shares. My problem is: i succesfully opened the share yesterday, it worked well one time but since that i couldnt open it via \\domain.com\share only via \\dc01\share or \\dc02\share.

> > That would be called a milliwatt generator. It likely exists in their > central office, but its typically used by their technicians to ensure > new installations meet specs and sometimes in troubleshooting. Call your > telco repair number and see if they will give you the telephone number > for it. I'll try that. 1st line technical support at Telstra are not known for

I have an x100p which suffers from echo (no surprise there apparantly :), and a few of the things I've read about tuning out echo say the first thing to get right is the tx and rx gain, and for that you need a few different types of test lines from the telco (Telstra, Optus, whatever). Does anyone have any numbers in Australia for such lines? I think they just need to send out a tone of a

Hi everyone, I am a LLVM newbie. I need to write a machinefunction pass for my project. This should be an analyzer of the machine code to do some profiling. I have written a couple of function passes for front end, but it seems they are completely different. I searched through forum and llvm documents, but couldn't find anything useful or questions were unanswered. Can anyone reference me to

I'm planning a system, just need to know if it works with Telstra's network. Cheers, Clint Sydney, Australia

I've installed a TDM400. Having a go with AMP. I would like incoming calls to be put throuhg to an extension (at my desk) and a mobile (cell phone) at the same time. Whichever picks up, gets the call.. This should be possible with AMP (call groups, 200|201|0*0408xxxxxx), but it didn't work, so I have created a custom-incoming in extensions-custom.conf What is happening is, The extension

I've seen this question asked before but haven't seen a definative answer. Does the e100p work in australia? Did any one who was asking the question before bite the bullet and get one? I can get a te410 if i really have to but would prefer to stay with the cheaper option. Any comments appreciated, Thanks ------------------------------------------------- This mail sent through IMP:

Hi does anyone have a definitive list of countries other than those listed on the wiki which are supporting app_SMS on landlines using ETSI ES 201 912 ?? Thanks Tim Robinson Basingstoke, UK

Well, Once upon a time, I had problems receiving callerid, and then one day, Mark was logged into my asterisk box helping with something else, and I asked him about this, and he showed me a nice tweak to some source file that made it work. Some time later, I must have done hundreds of CVS updates, and along the way, lost the above patch (one liner) and so callerID hasn't worked for a long

I have a couple of X100P's in my system and while on calls they just randomly hang up for no reason. I have tried messing with the busydetect and callprogress setting them to yes and no same and still random hangups. Is there another setting I should be looking at? My zap config looks like. context = inbound-work include => extensions signalling

Dear John, Thank you so much for your help. I looked at those documents. Could you kindly answer the following questions: Does it mean that I have to make my own backend target in order to write a machine pass even if I want to run a simple machinefunction pass? for example,if I want my pass to get MIPS instructions as an input, I have to copy all the files from mips target and add a file to it

Hi folks, just a quick update.... we managed to solve our problem by getting telstra to turn of the STD pips on outbound calls. We don't the effect yet on inbound (but we haven't had problems in the past) as most of our lines with x100p's are generally only used for outboung. Gary .

Any chance of say digits being extended to recognise "*" & "# " ?? Heck these are digits on a normal keypad :-) Gary .