similar to: Open Ports

Does anyone know how to get any of these VOIP phones to allow me to do menu selections through asterisk, like when accessing voicemail and such. Thanks :P --

I'm running CVS HEAD. The last time I updated was January 7th, at which time everything was fine. Having updated again today, January 17th, I'm having problems with IAX2. I use the "bindaddr" directive for both SIP and IAX2, and while SIP respects it, IAX2 doesn't. It listens on every interface, and uses every one of them for outgoing source addresses. This breaks IAX2

Hi When I register a SIP or IAX client to asterisk and I dial to it from another UA then there is no problem at all But, when I register two or more clients to the SAME peer (with the same user/pass) and I call to this peer.. Then only the UA which registered the last will ring.. Others don't ring... What can I do about this?? I would like to register for example 10 UA's to the same

Hello, I'm trying to migrate my system to FreeBSD and the Makefile for asterisk-addons fails in the first make clean: bash-2.05b# make clean "Makefile", line 56: Missing dependency operator "Makefile", line 57: Could not find .depend "Makefile", line 58: Need an operator make: fatal errors encountered -- cannot continue I would like to think there is no

Hi, I'm slowly getting to grips with *. My next quest is to get IAX2/FWD calls working. I've setup a fwd account and added IAX capability to it via the website. I got the email saying it had been done with some welcome text and sample phone numbers to try, such as 10001 for the answer phone. I followed the setup example on the fwd site for configuring * to work with fwd's IAX.

Hi, i just installed latest asterisk on fedora rc2 and on the same machine i installed a sip soft phone called kphone. Kphone complains about /dev/dsp being used and can't place/answer calls (/dev/dsp is obviously used by asterisk) . how can "share" my sound card with these two programs? or can i disable the sound card in asterisk so i can use kphone to place/answer calls? BTW kphone

what is the best way to have 2 asterisk servers communicate with each other?

Hi everybody. I'm trying to find a way to connect two (or more) extensions directly without being kept in the middle during the conversation but it won't happen. The purpose here is to have asterisk running on a low bandwidth (128Kbps) internet connection just as some kind of a proxy between some ip phones with high speed (10Mbps) internet connections. SER is not an option, for now.

Hi all. Can someone recommend a good UPS for using with an * machine that provides some linux tested software to do managed shutdown in case of power loss? Thanks. Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd. Office: +972-3-9230686 ext. 179 Fax: +972-3-9216642 Mobile: +972-54-8000200

Got no responses to this, but the list seemed to be down for a while, so here it is again. Sorry for the extra bandwidth! John Hi, I've been messing with getting SIP working for days now, with limited success. I've got Asterisk set up on a remote server with the echo test. Please try it out to verify I've got the server working right: sip:robot at nixon.butchwax.com

Hello all, I am trying to upgrade the firmware on my cisco 7910 without using CCM. I was told that chan skinny is possibly capable of doing that and would like to make sure. I have P00405000600 firmware which I have put in version in skinny.conf. the phone basiclaly stops at verifying load. tcpdump shows nothing happening apart from small amount of traffic to port 2000 (skinny). Does anyone

Hi, I'm following, http://www.voip-info.org/wiki-Asterisk+phone+sjphone. However, I cannot find the SIP tab. Would someone please give me a few pointers? The screen capture can be seen at URL below http://www.dslreports.com/forum/remark,12022987~mode=flat Regards, Norman Zhang

Hi, May I ask what does exten => s,1,Answer exten => s,2,ResponseTimeout(5) exten => i,1,Playback(pbx-invalid) s, t, i stands for? It says it is someexten but I still don't get it. Regards, Norman Zhang

Hi, I'm running asterisk-1.0.2-2mdk. When I tried to start it with /usr/sbin/asterisk -vvvvvvvvvvvvvvvvvvvvgc, I get [codec_ilbc.so] => (iLBC/PCM16 (signed linear) Codec Translator) Ouch ... error while writing audio data: : Broken pipe # ps aux | grep mpg123 root 5237 0.1 0.4 5816 4444 pts/0 S 18:45 0:00 mpg123 -q -s --mono -r 8000 -b 2048 -f 4096 fpm-calm-river.mp3

Hello , I learn handbook-draft.but I think I don't understand asterisk. where I can find some learning book about asterisk? thank u. B.R. John. -----????----- ???: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]?? asterisk-users-request@lists.digium.com ????: 2004?12?24? 7:51 ???: asterisk-users@lists.digium.com ??: Asterisk-Users Digest, Vol 5,

Hi, I'm using samba-*-3.0.6-4.3.100mdk and libkrb51-1.3-6.3.100mdk on LM10.0. A similar summary to what I'm seeing could be found here. http://lists.samba.org/archive/samba/2004-July/090210.html My relevant config info could be found below. May I ask how could I solve this in LM10.0? What packages do I need to update? The problem does not arise with NT. It happens to only W2K, XP,

Hi, I'm using samba 3.0.6. I see computer_name folders created in homedir. This never happened before I switch from Domain to ADS. Could someone please give me a few pointers? Regards, Norman Zhang [global] workgroup = ARKONDOMAIN realm = HQ.ARKONNETWORKS.COM server string = Samba Server %v security = ADS obey pam restrictions = Yes

Hi there, http://www.seagate.com/support/disc/download/seatoold_en.exe Seagate offers a Windows executable (needs Win98 or better, 1,9MB) that should create 2 bootable floppy disks that contain a harddrive check program. Invoking "wine seatoold_en.exe" works, but when the floppy should be written, an error occurs "insert 1.44 MB...click retry". I tried to mount a DOS

Hi there, to get a laptop with recent AMD Vega mobile GPU (aka Raven Ridge) running with hardware acceleration I need to build the latest mesa with the latest llvm. I downloaded llvm 7 from svn. Unfortunately, when trying to build mesa 18.0.rc3 with this llvm version the make process fails with lot of "undefined reference to LLVMxyzblahblah" messages. Llvm 5.x is probably not

The setup is a samba server with mixed clients (samba clients and windows clients). The problem, I want the linux client to mount there home to their home share on the server. The problem is, I have followed the guide mentioned below and everything works except that the linux usernames have the format domeinnaam+username as a result of which pam_mount wants to mount