similar to: chan_sccp and 7920

Greetings, I have seen a few postings in the past regarding the interop of Asterisk and the Cisco 7920 WiFi phone. To date, I have not seen a definitive method to getting the phone working. Assuming someone has this actually working, can that person step up and answer these questions. 1) What Channel is it working with (chan_skinny or chan_sccp)? 2) If code was used that is not a part of a

Hi all, we are happy to announce the new test-release of chan_sccp. The Cisco 7920 support is working now, however, some call handling stuff is hardcoded for testing. Also some more in-deep-knowledge of Skinny was archieved, how they handle calls. Please test it with your 7940/7960 and 30VIP and report any problems using our bug tracking tool. The latest tarball is available at:

I configured my sla.conf to use with a Polycom phone. I have no idea if I did it right, however, none of the console "sla" commands exist. Do I have to something special to compile in this support, or should it just work out of the box? ~jay

Hi, everybody. I was just running into a DynDNS Problem. One of our phones has a fixed IP, but the * box only has a dynDNS IP and a fixed name. So all phones running SIP are able to "survive" the change of the IP address, but not our Cisco 7920 - it changes state to "connecting to CM0" and hangs there until reboot. After reboot it looks up the current IP address of the * box

release 20050730 http://chan-sccp.berlios.de/ <ftp://ftp.berlios.de/pub/chan-sccp/chan_sccp-20050730.tar.bz2> - very experimental hint (busy status line lamp or icon) support. This is a very experimental system so it might not work properly with particular cisco phones. 7960, 7970 and 7940 with recent firmware does work great. Old phones can't, of course, use the hint system. There

>Does the CVS has the 7910 support as well ? >If you want I can test it on asterisk/OpenBSD. > > yes it's supported. I can't really get it to work right 'cause I just have ciscos 7960/7905. Can anyone donate 7910/7920/7970? I will make them work just like they work in CCM, otherwise I will send them back :-) Sergio

The chan_sccp page at http://www.voip-info.org/tiki-index.php?page=chan_sccp2 has been updated. See the bottom of the page. Thanks. Comments welcome. -- respectfully, Joseph =============== ---------------------= ********** =

Hi All, have some decent success on the 7920 "activation" in Asterisk. Latest status: chan_skinny does NOT work with 7920 chan_sccp does WORK with 7920 (!!) however: to remove coredumping the chan_sccp just comment out the MWI (messagewaitingindicator), then it compiles fine. Then change sccp_helper.c: return "P0060302" instead of the old value. and voila: Phone is

I have asterisk 1.09 running with chan_sccp.20050701 on Fedora core 4 with kernel 2.6.12. I have a Cisco 7940 working with X-lite working on XP too, connecting to each other, Asterisk and FWD. The 7940 upgraded to SIP7.4 with xmlDefault.cnf.XML getting delivered via tftp using the loadInformation8 parameter method taken from voip-info.org ("Configuring Cisco 79xx phones with Asterisk"

I am impressed, I have been trying this for sometime using the SIP image and the only difference I can create is a 'single' and a 'double' ring on the phone. I use the 'single' ring for phone calls and the 'double' ring for the doorbell. I would love to be able to choose a ring tone based on the incoming msn or callerID. The idea of the phone shouting 'Its the

hi! i had some good news regarding the cisco 7920 and the internetworking with asterisk (and possibly SIP ?). Status: chan_sccp.so not coredumping anymore :-) Phone contantly in reboot loop [see below] :-( Reboot Loop means: ------------------ Phone auth's with AP Phone gets IP from DHCP & TFTP Server Phone loads OS7920.TXT Phone loads SEP<macaddr>.CNF.XML Phone loads

HI all: I have spent a large amount of time configuring/installing phones connected to Asterisk. Halfway through the process I discovered that my Cisco7960 with 2 7914 expansions was not supported in the SIP protocol. After reverting to SCCP 6.0(4.0) I am now perplexed with the hassle of configuring SCCP to properly work with Asterisk. So far I have gotten the phone to dial and receive calls

Hi, I?ve been following some information about the latest chan_sccp drivers for a few weeks. I installed and tried about any variant of driver that exists in the chan_sccp system. Despite a few little changes in the CLI options I am still encountering a lot of problems with the phone. When not using the phone for a while, it "disconnects" from asterisk (1.0.7) after a few hours

Hi Siggi, > > 7960 and then "Call Ended" on the Display (curious about that !!!). > > That seems to be normal for the 7920. I've sniffed the registration > procedure with Cisco's newest 3.3(3) CallManager (+patches), and it's > doing the same thing. Maybe that's some odd way of testing if the > CallManager ("CCM") really works... >

John Todd wrote.... > Cisco has an 802.11 phone called the 7920, which is apparently > shipping now. It is very expensive (>$550 USD) and only runs SCCP at > the moment, which is Cisco's proprietary VoIP protocol. However, if > it falls in line with some of Cisco's other high-end VoIP equipment, > that means it should have a trailing-edge SIP image running by

I've submitted to Julien http://chan-sccp.sourceforge.net/ my patches the diff file is attached to this mail Apply it to the CVS head cvs -d:pserver:anonymous@cvs.sourceforge.net:/cvsroot/chan-sccp login cvs -z3 -d:pserver:anonymous@cvs.sourceforge.net:/cvsroot/chan-sccp co -P chan_sccp it does include: - added support to cisco 7905 - major buttontemplate rework. Added a validMask function

Hi, I have an asterisk running great, with 2 cisco 7912 phones converted to SIP, and a cisco 2600 xl w/ E1 and SIP. I?m thinking to expand the test adding more 7912, but I prefer not convert all the 7912 to SIP, so I?m tying to put CHAN_SCCP to work. I?ve get the sources from cvs.sourceforge.net but when I try to compile, get the followings errors: [root@asterisk01 chan_sccp]# make Now

Just wondering, I noticed on the chan_sccp site that a new release should have been released on 20-Jan-2005. Is there any news on the status of this release? As far as I can tell even the sourceforge CVS for chan_sccp didn't change much around that time - or since. -Chris

Hi, I recently bought a 7910. I found out too late that it would not do SIP as I initially thought. Anyway before ditchingit for a 7960 I wanted to try it out, I read that the guys at http://chan-sccp.sourceforge.net/ had done some improvements to the original chan_sccp driver and having 80% functionality with this model. I have not been able to compile their driver and keep getting the

> > When dialling a number, my 7960 always says "External call". Is there > any chance to tell it the difference or make it display the dialled > number (especially nice when using speeddials)? > CallInfoMessage issue, it should be fixed by Jan in the CVS, I will check it out > Is there any way with chan_sccp to have asterisk taking influence on the >