similar to: Which Primary ISDN card to use in Europe ?

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |

Hi, I'm pulling my hair down and getting bold :-) ..... I have Asterisk between Panasonic KXTD816 and Euroisdn in Italy (beronet octobri and bristuff Asterisk).... I'm trying to do just plain transfer of call from pbx to ISDN through Asterisk... It seems like PBX hangsup, when call is progressing with no apparent reason. I'd kindly ask for any advice or some working example for

Hi Folks, First of all, I've been reading a lot and a lot about asterisk and ISDN-BRI, but is really a complicated world, not like PRI or Analog. I have 2 offices with 2 NT boxes and I want to connect them with Asterisk to route outgoing from one office two the other. At the end I want them to look like this Office2 will have only VoIP phones (not ISDN phones connected to a card in asterisk)

Hi, I'm pulling my hair out, cause cannot connect to EuroISDN BRI in Italy with octobri card from Beronet. I use bristuff and have following zaptel.conf... # # This file is parsed by the Zaptel Configurator, ztcfg # # # First come the span definitions, in the format # span=<span num>,<timing>,<line build out (LBO)>,<framing>,<coding>[,yellow] # # The timing

Hi, I wonder which PRI interface card is most stable and supported for EuroISDN and Asterisk ? Are they stable enough ? Any tips ? Thanks in advance, regards, Rob.

Hi, I'll soon replace a Junghanns OctoBRI with a Junghanns QuadBRI. As both use wcb4xxp driver (dahdi 2.3.0, libpri 1.4.10.2 and asterisk 1.6.1), I'm planning to proceed this way : 1. Edit 2 versions of files /etc/dahdi/system.conf and /etc/asterisk/dahdi-channels.conf (one for each card). 2. Link current system.conf and dahdi-channels.conf to QuadBRI files. 3. Power PC off 4. Swap cards

Hi, I'm getting unreliable dtmf recognition (it works fine for 4-5 digits, errors (duplicates) on more), when transferred inband from gsm gateway to NT port of quadbri under bristuffed Asterisk..... Since Asterisk is claimed to have good dtmf recognizer, I suspect there are some settings to workarouned... I've tried dtmf relax, but didn't help, so I suspect gain settings.... Is

Who is selling the quadBRI cards, which is everybody talking about? And how much does is costs? I'm looked on the site of junghanns.net, but there is no selling information. A seller in germany is favored.

Hello, Is anybody there using quadBRI form Junghanns.net with Asterisk ? I would like to order that card but first would like to hear some opinions. Thank you in advance Bartosz

Hi, I'd like to use Asterisk with ISDN interface and normal analog interface to door phone (or any other low cost connection type to door phone). What would be your recomendations for needed HW in Europe? Is it possible to have this in one PCI card? Are there any lower cost voip door phones? Thanks in advance, Robert.

Hi, I mistakenly posted this to Dev list.... I wonder if I use quadbri or octobri cards to insert Asterisk between ISDN PBX and ISDN line - if power of Asterisks fails - will those card connect PBX directly to ISDN line ? If not are there any other simple switching devices, that would do this (in power fail it will connect ISDN PBX to ISDN lines directly) ? Thanks in advance, regards, Rob.

Hi, I'm using a revision 6822-enabled Dahdi-Tools (see https://issues.asterisk.org/view.php?id=13897) with a Junghanns QuadBRI. 1. Do I still need qozap driver ? If positive, how is it recommended to get it ? 2. Which line should be included in /etc/dahdi/modules to have the appropriate driver loaded ? 3. The process I'm planning to use is : A- Hand edit /etc/dadhi/modules,

Hello, We have a quadBRI in NT mode with bri_cpe_ptmp signalling and when connect a ISDN telephone to this nothings happen. What can I do? My config files are this: Zaptel.conf: loadzone=es defaultzone=es # qozap span definitions # most of the values should be bogus because we are not really zaptel span=1,1,3,ccs,ami span=2,1,3,ccs,ami span=3,1,3,ccs,ami span=4,1,3,ccs,ami bchan=1,2 dchan=3

<P>Hi List,<BR>is it possible to connect an existing telefon system with a stanard AVM ISDN card to the telco?</P> <P>&nbsp;</P> <P>[ISDN from Telecom supplier] ---- [Aterisk Box] ----- [ existing telephon installation]</P> <P>&nbsp;</P> <P>kind regards,<BR>Patrick</P>

I wrote a week or two ago about a problem I was having with a TDM400P with 2 FXS. The problem was reliable fax transfers. There were often slow or had communication failures during transmission. Richard replied to my post and told me this is an ongoing problem that might have a solution in the weeks to come. However, I was wondering if anyone had any alternate solutions for faxing with an

Ok, I usually use the latest stable CVS, with no patches or modifications. If figured if there was a worthwhile patch, Mark would have already included it. However, there was that neat patch about being able to press a certain key and it'd begin recording in mid-stream, that was an awesome feature and I patched my latest features.c file with that patch. But I keep seeing mentions of other

Hi, Using Xorcom's bristuff-0.4.0-RC4-xr7.tar.gz (ie asterisk 1.4.25) with an old Junghanns OctoBRI (ie not the 2.0 version), zttool shows every port in TE mode, though half of them are in NT. Alarm column shows OK for every port, such as : OK octoBRI PCI ISDN Card 1 Span 1 [TE] Lay Globally, this system doesn't work (can't dial out through zaptel) Replacing this board

Hello, I've got a running system in which logs are full of messages such as: [Jun 10 07:24:14] NOTICE[2414] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 2 The strange thing is those messages are coming from a single span. My setup is : Asterisk 1.6.1.18 Junghanns OctoBRI with wcb4xxp driver libpri 1.4.10.2 dahdi 2.3.0 3 BRI lines in PtMP mode What does this

Hi there, I just upgraded a relatively old Asterisk installation (1.2) in our office to a relatively new version (1.6svn from last wednesday) which runs a Junghans QuadBRI card [1]. To get this flying I got dahdi-linux, dahdi-tools and libpri from SVN as well. After a while of juggling it "works". What doesn't work: connected ISDN devices (Gigaset phones connected to QuadBRI