similar to: using built-in extension numbers on the ZAP channel

Hello, I have found a "bug", I think in the way TDM400P cards handle FXO interface disconnect/re-connect problems. Normally I do keep all the wires connected from my CO / PABX quite securely, but I had a need to re-route the cable from one side of the desk to another, and I simply disconnected the RJ-45 connector and plugged it back in. THIS PROMPTLY RESULTED IN VERY VERY SCRATCHY AUDIO

Hello, I want to use Asterisk PBX in front of my old, legacy PBX. The legacy PBX can be outfitted with caller-ID and is already able to handle Calling Party Control Signal Detection (this is a Panasonic KX-TD1232 Super Hybrid PBX. My question is how would one enable Asterisk to control the TDM400P/FXS port to provide to the /FXO CO port on the legacy PBX, support for proper answer supervision/CPC

Hello, I would like to parse inbound Asterisk IAX2 7-digit numbers in the form of 123-4567 and strip out the first four digits, and then dial whatever number digits remain. If I only have three digits (000-999) and have a mix of channels (ZAP, SIP, IAX2) could someone please point out how I can use a single DIAL command to just dial the extension regardless of the type of channel. .. For each

hi, we have just received our first shipment of digium cards, FXO + FXS combinations, and collected all the hardware for our custom clone server which will house our test-bed for asterisk. I'm based in Dhaka, Bangladesh so you will understand we may not always be able to get all the hardware we need, when we need them and in the manner that other people are used to.. from a catalog or from a

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.298 / Virus Database: 265.6.6 - Release Date: 12/28/2004

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.300 / Virus Database: 265.6.8 - Release Date: 1/3/2005

Hello, I thought that my Digium TDM400P would be the right hardware to support the zaptel timer, and put the following IAX.CONF entry to test, (trunk=yes) in the example below [VHAX] type=peer auth=md5 username=whoknows jitterbuffer=yes ;trunk=yes secret=terriblesecret host=4.5.6.7 qualify=1200 disallow=all allow=ulaw allow=gsm ;allow=g711u ;allow=g711a But, it didn't work. So I had to

hi all, I need help ! What are Built-in Extension Numbers ? if i dial *69 with callreturn=yes in zapata.conf i don't get the last caller . How may i use Built-in Extension Numbers ? I should not add extensions in dial plan !? Harry from voip-info.org: There are some "extension numbers" that are built into the Zap channel module. You may override these in your Dialplan, i.e.

Hello I just brought my machine back up from a very nasty crash. Not sure what caused it yet but whatever happeed cause the journal to be foobared. fsck dropped the journal and then proceeded to check the fs. I have a directory called websites which fsck unlinked. however when i look in debugfs i see this.. 622669 40755 0 0 4096 13-Jan-2002 22:39 home3 2133571369 --- error ---

I have a text file that I have imported into R. It contains 3 columns and 316940 rows. The first column is vegetation plot ID, the second species names and the third is a cover value (numeric). I imported using the read.table function. My problem is this. I need to reformat the information as a matrix, with the first column becoming the row labels and the second the column labels and the cover

Hi. The patch against p4 no longer works -- did work for a while though. Is there anything against pre12 yet? Thanks. -- John Covici covici@ccs.covici.com

Hi, I just wanted to compile my kernel 2.4.13 with the ext3-2.4.13-pre6 patch, but it doesn't work. It seems, that the patching failes by replacing some things in a textfile. Does anyone of you know, if there is a upcoming solution for this? Kind regards Jan Albrecht -- Jan Albrecht Phone: +49-5241-80-88404 System Consultant UNIX/NT Fax:

Dear Sir, When i am trying to set CRAN mirror to install packages, its showing the following messages, i can't install the packages > > > chooseCRANmirror() Warning message: In open.connection(con, "r") : unable to connect to 'cran.r-project.org' on port 80. Best regards Mahmud [[alternative HTML version deleted]]

Hello, The 0.9.9 2.4.10pre4 patch doesn't apply. There are 5 rejects. The first three are easy to fix, but the fourth in vmscan.c will be very difficult without being a developer. The fifth I am not sure about. This brings up the fact that many of us are using ext3 and have to patch every time a new kernel comes out. I really think we need to strong arm Linus or something and get

Hello, It's several days I try to track this bug, and even cannot cook a reproducible example. Yet, it occurs consistently in a long-running task after a variable period of time. Here is an example: ... my long-running code [as I said, cannot give something simple that produces this bug in a reproducible manner] Error in match(x, table, nomatch = 0L) : formal argument

hi, please help me out in the following case. seems like it stuck in some where(already 7 hrs passed). what I want is to combine 4 matrix in to one matrix of desired length. final_matrix<-function(ob_feat,content_feat,link_feat,link_feat_transformed){ complete_feat<-matrix(rep(-1),nrow=11402,ncol=278) for(i in 1:8944) {q<-c(0) for(j in 1:11402) {

Someone recently posted the following list as functions built into * *0# sends flash *8# remote call pickup (pickup phone in your group) *67# disable caller id *70# no call waiting *78# do not disturb on *79# do not disturb off *72# enable call forwarding *73# disable call forwarding *82# enable callerid I'm running a CVS from a couple of weeks ago with multiple C7960's, snom 200,

I do think keeping the default behavior is desirable for backwards compatibility; my suggestion is not to change default behavior but to add an optional argument that allows a different behavior. Although this can be implemented in a user-defined function, retaining empty matches facilitates programmatic use, and seems to be something that should be available in base R. It is available, for

When I run R CMD check R.oo on R v2.7.0 devel (2008-03-04 r44677) on WinXP I get the following error while testing examples: Error in match(x, table, nomatch = 0) : formal argument "nomatch" matched by multiple actual arguments Calls: setMethodS3 -> setMethodS3.default -> %in% -> match Execution halted How is that even possible with: > get("%in%") function (x,

Hi, I seem to have a problem with compiling the kernel 2.4.13 on redhat 7.2? It would compile fine but have errors about ext3 support on reboot. I download ext3-2.4-0.9.13-2413.gz to my linux machine to enable it be useful with ext3 support but when I try to gunzip it with the instructions gunzip < ~/ext3-2.4-0.9.13-2413.gz | patch -p1 i get gunzip: stdin: not in gzip format I get an