similar to: voice + data

Displaying 20 results from an estimated 4000 matches similar to: "voice + data"

2004 Dec 02
0
new asterisk installation report and request for mixed voice data apps
hi, I followed the instructions faithfully in http://www.voip-info.org/wiki-Asterisk+Fedora+Core+3 and the directions were very understandable and almost painless. I did miss the documentation, as "make progdocs" would not work since the package "doxygen" was not included in that WIKI guide, and probably that means I will have to spend some more time in "digging"
2004 Dec 05
2
ANALOG FXO ZAPTEL & WCFXO & WCTDM module issues seen with intermittent analog lines
Hello, I have found a "bug", I think in the way TDM400P cards handle FXO interface disconnect/re-connect problems. Normally I do keep all the wires connected from my CO / PABX quite securely, but I had a need to re-route the cable from one side of the desk to another, and I simply disconnected the RJ-45 connector and plugged it back in. THIS PROMPTLY RESULTED IN VERY VERY SCRATCHY AUDIO
2004 Dec 10
2
using built-in extension numbers on the ZAP channel
hello, using a legacy PBX to access a Asterisk Zap channel (Legacy PBX FXS --> FXO application Asterisk/TDM400P) I want to be able to "flash" the asterisk pbx. However by pressing the FLASH button on the extension connected to the Legacy PBX gets me the flash features on the Legacy PBX, not on the Asterisk PBX side. I thought of using the following codes (listed below) from
2004 Dec 01
1
pre-installation jitters
hi, we have just received our first shipment of digium cards, FXO + FXS combinations, and collected all the hardware for our custom clone server which will house our test-bed for asterisk. I'm based in Dhaka, Bangladesh so you will understand we may not always be able to get all the hardware we need, when we need them and in the manner that other people are used to.. from a catalog or from a
2004 Dec 09
1
can FXS ports on TDM400P provide Battery Reversal or CPC
Hello, I want to use Asterisk PBX in front of my old, legacy PBX. The legacy PBX can be outfitted with caller-ID and is already able to handle Calling Party Control Signal Detection (this is a Panasonic KX-TD1232 Super Hybrid PBX. My question is how would one enable Asterisk to control the TDM400P/FXS port to provide to the /FXO CO port on the legacy PBX, support for proper answer supervision/CPC
2004 Dec 10
0
analog FXO debug suggestions
[resend in plain text format] > On Tue, 2004-12-07 at 09:34 -0600, asterisk-users- > > request@lists.digium.com wrote: > > > I've been struggling with a test * install for a couple months now in a > > > small office and am just about ready to give up on it. It's not that the > > > system itself is a problem. I've got everything (attendant,
2004 Dec 19
2
dialplan selection
Hello, I would like to parse inbound Asterisk IAX2 7-digit numbers in the form of 123-4567 and strip out the first four digits, and then dial whatever number digits remain. If I only have three digits (000-999) and have a mix of channels (ZAP, SIP, IAX2) could someone please point out how I can use a single DIAL command to just dial the extension regardless of the type of channel. .. For each
2004 Dec 07
0
Subject: Re: Analog FXO Woes Continue
> On Tue, 2004-12-07 at 09:34 -0600, asterisk-users- > > request@lists.digium.com wrote: > > > I've been struggling with a test * install for a couple months now in a > > > small office and am just about ready to give up on it. It's not that the > > > system itself is a problem. I've got everything (attendant, voicemail, > > > FXS
2004 Jun 20
1
Data over Voice through Asterisk
Hi, I'm trying to make a dialup internet connection through my asterisk PBX. When I bipass the Asterisk box, I can get 51600bps. When I run through the asterisk box, I'm limited to about 21600bps. I have a TDM31B card. Any help on speeding these connections up would be good - I was on the understanding that if you bridged the channels, then the call should essentially flow straight
2004 Dec 10
0
providing battery reversal from Asterisk to legacy pbx
> > You need to configure your legacy PBX to send a flash through from your > legacy phone to the legacy FXS port that is hooked to a * FXO port. This > is not something you can do from the * side. > > *0 is asterisk's way of doing this. You need to find out if your legacy > PBX has a similar method. It may not be possible. Of course you failed > to mention what kind of
2005 Jan 05
1
TDM400P + Asterisk + zaptel timer ?
Hello, I thought that my Digium TDM400P would be the right hardware to support the zaptel timer, and put the following IAX.CONF entry to test, (trunk=yes) in the example below [VHAX] type=peer auth=md5 username=whoknows jitterbuffer=yes ;trunk=yes secret=terriblesecret host=4.5.6.7 qualify=1200 disallow=all allow=ulaw allow=gsm ;allow=g711u ;allow=g711a But, it didn't work. So I had to
2004 Dec 16
0
kewlstart - explanation of this method, please ?
Hello, is there a full guide to what kewlstart is supposed to do with FXO or FXS lines ? is it only applicable to one of the interfaces FXO -or- FXS but not both ? I asked earlier if FXS lines can be made to reverse polarity, and someone else pointed out that the chipset on the FXS ports seems to support it, perhaps the driver in the asterisk zaptel interface module needs to be modified to support
2006 Feb 23
0
How to install Zaptel?
I greatly appreciate the help at last Monday's installfest and especially am grateful to Chris and Lenny. Now I am reconfiguring the installfest computer to add Zaptel using the instructions at http://www.voip-info.org/wiki/view/Asterisk+Zaptel+Installation There is now a Digium 4 port card installed. In regards to Zaptel there are some questions on zconfig.h. Should I: #define
2005 May 19
1
RHEL 3
Anyone tried to build * + h323 to rhel3... I have to problems in the process... a) Zaptel would not build - a whole bunch of errors about kernel... b) make progdocs failed with reference to dot - check your installation. Do I need the zaptel ?? I will not be using any interface cards.. I'd like to make progdocs - any suggestions there? Latest cvs on everything.. Thanks
2004 Jul 25
1
Can not make progdocs
Not even sure how important this is considering the state of many of the online docs... I have doxygen installed as is noted for the requirements for 'make progdocs', but the make doesn't find dot. I have no idea where dot went, is or should have been... I am installing und Suse 9.0 and it's rough. If you forget something duringthe initial install, adding the package later
2004 Dec 17
0
[Off Topic] humour, XMAS, ground loop - good business strategy
hi, I received this e-mail which contains a "ballad", at first I thought it was junk mail, but then I read through it, for the EE members of this list, it may be quite humorous. I don't know if the ballad is original, but at least it's the XMAS season, so it's something to lighten up your day, eh? -samudra """ How the Ground Loop Stole Christmas
2015 Mar 26
1
CDR dst value null after attended transfer
I'm having an issue with CDR. Basically, I expect to have all "legs" of a call having the same linkedid and differing only by the sequence value. That does happen, but I'm getting null dst values after doing an attended transfer. I'm not sure if this is a bug or I'm doing something wrong. I'm running Asterisk 13.2.0. Here's the console log, step by step: First,
2005 Aug 14
1
PABX and Asterisk Dial Plan
Hi All, Can Asterisk dial extension which resides in the PABX? (eg. 2000) Sip Phone <-----> Asterisk <------> ATA (FXS) <------> (CO side) PABX <-----> Extension (eg. 1000) (2100 & 2101) can my sip phone call to pabx extension 1000? What will be my dial plan? I know I can connect to 1000 by
2007 Aug 10
2
Locating Asterisk documentation after installation
Hello all, After installing Asterisk, i have installed the docs by "make progdocs". But i don't know where to locate this documentation. please Help. Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070810/ceb95948/attachment.htm
2006 Apr 26
1
Intergrate Asterisk IP PBX with Legacy PBX, continuing existing funtionality of legacy pbx
Hi All, I would like to explain the layout that i am trying to achive. I am so helpless on this regard. So here is the story ........ " This is with regard to the setup which you can find at the "Asterisk The Future of Telephony" , chapter 11, page # 196-197, I am attaching the picture for your information. Now I am taking a challenging step to of integrate IP PBX with our