similar to: Swissvoice IP 10S VoIP Telephone

I am in the process of setting up an * system using Polycom IP 500's. I don't want to spend time setting a ftp server for application and configuration files at the moment, just want to use the web interface to the Polycoms. DCHP works OK and IP is obtained correctly. Polycom fails to load .cfg file and holts. I have read the 143 page admin user guide a couple of times...and I missing

I have set up a new SwissVoice phone and it can receive calls but I cannot make calls out from it. The setup is simple for now, 2 phones: SwissVoice is ext 7726 and Cisco 7960 (SIP) is ext 7999. I can call from the Cisco phone and it rings on the SwissVoice phone but when I dial from the SwissVoice phone I get a busy tone upon dialing the second digit. The log reads as follows: -- Endpoint

I have a SwissVoice IP10S but can not seem to get it to have dialtone or dial on *. Calls to or from 3001 don't work. Any ideas are appreciated. Robert mgcp.conf is: [general] port = 2427 bindaddr = 192.168.0.110 [ip10] host = 192.168.0.5 context = from-sip line => aaln/1 The portion of extensions.conf is: exten => 3001,1,Dial(MGCP/aaln1,20) exten => 3001,103,Hangup

hallo, does anybody successfully managed to get swissvoice ip10s with h323 firmware work with asterisk ? mgcp firmware works fine, but with h323 i'm still getting one way audio. regards Marian -- SUNTEQ s. r. o. Hviezdoslavova 9 # Prievidza # 971 04 # Slovak republic Tel: +421-46-5430 754 # Fax: +421-46-5439 144 http://www.sunteq.sk/

Hi! I am doing a research about the prices of SIP telephones. If someone can tell me which one are the cheapest and have an acceptable quality... it will be very kind. Best Regards, Mireia

Hi Does anyone have a howto on how to set one of these up on Asterisk or Trix box please? I can make it SIP or MGCP so whatever you have ;-) I have found one page but it isn't really a howto setup Thanks in advance Paul -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, Does anybody know the place to download the firmware for swissvoice ip10s I have several phones with application IP10 H3 v1.0.0 (Build 1) I'm looking for newer H.323 and also MGCP firmwares Are the SIP firmware available, according to web its targeted to Q1 2004, but we have week left in Q2 I sent several email to swissvoice support,, no answers Regards Juri

I have 1 IP phone (Swissvoice IP10S) and 1 POTS phone. When I dial the number for the IP phone off the POTS phone, the IP phone rings. But when I pick up the handset on the IP phone, I get a busy signal and this message on *: Aug 23 09:38:57 NOTICE[1142106560]: chan_mgcp.c:2243 handle_response: Terminating on result 502 from svip10@00059002042b-1 Here is the entire session. svip10 is the 1 and

Hi there, tonight I upgraded one of my ip10 phones to "Appli 1.0.0 build 3" with "Boot 0.3.6" This firmware is dated Dec.19, 2003. For Robert (aka "info lists") this fixed the multiplied digits problem (which I never had). Since there is no website of Swissvoice I guess you'll have to e-mail them if you want upgrade... Unfortunately the upgrade did

taken from bug 881 (now resolved) :-( ---------------------------------------------------------------------- markster - 05-19-2004 09:21 CDT ---------------------------------------------------------------------- As it turns out the 10S cannot conference on the device. From Jean-Francois at Swissvoice: Hi Mark, IP10S have not the capabilities to mix by itself 2 RTP flows, that why it refuses

I'm not sure that the problem lies in the NAT because the phone is talking to Asterisk. I'm hoping this is a simple config thing I've overlooked but I've tried all kinds of combos inside the [] in my mgcp.cfg file. The phone's IP is 192.168.1.116 (my comp is .110). The router to which the phone and my comp is plugged into has a WAN IP of 10.0.0.28. All the other comps (and SIP

I need to purchase approx. 10 phones for a small office implementation. Nothing fancy is required besides a full-duplex speakphone, in the sub-$200 range. I am currently looking at the Polycom Soundpoint 500, Uniden UIP-200 and SwissVoice IP-10. I have searched around and found various posts regarding each phone's ability to work with asterisk (SIP, I probably should have mentioned), but

Hello, Now that I have a nearly working configuration for my IP10S with * I wonder if anyone has done call transfert with this Phone. In the IP10S documentation they talk about the 'service key' wich is the key with the white dot on it. With this Key, it should be possible to have a menu with call transfert entries. This menu should (accordingly to the documentation) depend on the

I had the telnet window to the phone open by chance and noticed this line twice when I tried to call the IP10: WARNING: may need to undo rtp port operation here The warning line appeared immediately when I picked up the handset. I have no idea what this means. I also tried calling the phone from a POTS phone and I got the same warning. What is even better is that this coincides with the

Hi there, here some questions and experiences after playing for one day with 3 Swissvoice ip10s and the latest * CVS: QUESTIONS: - what is the user option "enter voice mail number" good for? It doesn't appear to be of any practical use - does anyone have some Swissvoice info that I cannot find on their web site like the guide to MGCP XML (.svd), guide to configuration file

Does MGCP transverse NAT? Seeing as the only decent yet cheap IP phone is the Swissvoice, it would be rather helpful.

I'm going to install asterisk with four digium cards. Can anyone mention a brand that carries boards with 4 compatible pci slots? Thanks Shoval Tomer, IT Manager, SofTov Advanced Systems, Ltd. Office: +972-3-9230686 ext. 179 Fax: +972-3-9216642 Mobile: +972-54-8000200

Dear Friends, We have implemented "Asterisk" in our organization. There are 150 members in our organization. At present all are using softphones. Now, I want to buy hardphones for our staff. Can anybody suggest me that what is the best hardphone for Asterisk with low-cost? Thank you. Regards, Chandra. --------------------------------- Ring'em or ping'em. Make PC-to-phone

Hi, I'm considering giving the Grandstream BudgeTone-102 phones a try. I've been using Cisco 7960's to date, but the low cost of the Grandstream phones are hard to ignore. I have two questions: 1) Does the message waiting indicator on the BudgeTone's work with Asterisk? 2) The one line 12-digit LDC concerns me a bit. Is the LCD able to display both the CID number and name on

Hi there, after testing with a MGCP phone (Swissvoice ip10s) I found the following ASTERISK-based codes (VERTICAL SERVICE CODES) to work - I assume that most of those will also work with SIP, but haven't checked that yet: *67 - Calling Number Delivery Blocking *70 - Cancel Call Waiting *72 - Call Forwarding Activation *73 - Call Forwarding Deactivation *78 - Do Not Disturb Activation