Displaying 20 results from an estimated 5000 matches similar to: "CPC, Calling Party Control, Disconnect supervision, -- how to tell that to Verizon (east coast)?"
2007 Jan 19
2
Disconnect Supervision UK / BT solution?
Hi all
I'm using sangoma a200 cards in the UK and have the ongoing, often noted
problem of disconnect supervision with BT POTS lines.
Just noticed this post on
http://www.voip-info.org/wiki/view/UK+Asterisk+Details
stating that potentially someone's got a solution :
"TDM400P & Not Detecting Hangups:
Got a TDM400P installed and having problems with Asterisk not detecting
2004 Dec 09
1
can FXS ports on TDM400P provide Battery Reversal or CPC
Hello, I want to use Asterisk PBX in front of my old, legacy PBX. The legacy
PBX can be outfitted with caller-ID and is already able to handle Calling
Party Control Signal Detection (this is a Panasonic KX-TD1232 Super Hybrid
PBX.
My question is how would one enable Asterisk to control the TDM400P/FXS port
to provide to the /FXO CO port on the legacy PBX, support for proper answer
supervision/CPC
2004 Dec 29
1
Can I tell if it hung up due to busydetect or disconnect supervision?
The FXO lines on my TDM400 are connected to PSTN lines in Israel. As far as
I know, the lines around here have disconnect supervision (I've seen some
other Israelis on this list, anyone know for sure?), because it's worked on
Dialogic cards, which reported hangup, not busy detect (while when I connect
a Dialogic card to a PBX, I have to measure the busy signal's
frequency/cadence or
2009 Sep 25
4
DAHDI disconnect supervision timing
Ok so this is officially driving me crazy. I have an Asterisk 1.6.1.6
install with DAHDI/DAHDI tools (latest) and an OpenVOX TDM400 card with 1
FXO port and 1 FXS port. I have a POTS line from my phone company attached
to the POTS line.
I have asked for "disconnect supervision" to be provisioned on my line and
they claim to have added it. However, my scenario is as follows:
I receive a
2006 Dec 29
2
Disconnect supervision in India?
Hey all,
anyone know the status of disconnect supervision on POTS lines in India?
Set up an asterisk box, TDM cards, in Mumbai, and doesn't seem to have
disconnect supervision......
Thanks
--
Chris Earle
System Solutions Specialist
2006 Feb 19
0
Viking CPC-Disconnect
Someone on the list a while back suggested that if you were having
problems with call disconnects, to look into a product from Viking
TellecomSolutions called cpc-disconnect:
http://www.vikingtelecomsolutions.com/catalog/model_CPC-1.htm
I received my unit on Friday and put it into place Saturday afternoon
(SBC in this area doesn't supply call disconnect supervision). The unit
was acting
2004 Jan 10
2
far end disconnect supervision
I'm starting to shop for my first channel bank and one of the features
that eveyone seems to recommend is "far end disconnect supervision".
What other terms do various manufactures use to describe this same
feature ?
Is "calling party disconnect" the same as "far end disconnect
supervision" ?
Thanks
2004 Sep 01
1
FXO Disconnect supervision
Does anyone have disconnect supervision working on their TDM400P or X101P
cards (to/from the telco)?
Googling "telco disconnect supervision," I found the following description:
http://mirror.lcs.mit.edu/telecom-archives/telecom-archives/TELECOM_Digest_Online/1559.html
[cut]
Re: How Do I Get "Kewlstart" From my Phone Company?
Paul A Lee
Tue, 24 Aug 2004 16:58:16 -0400
...
It
2004 Jan 13
3
How to Order Disconnect Supervision from SBC using Adit 600?
Can anyone help me with the term that SBC uses to refer to disconnect
supervision? I have an Adit 600 channel bank which has helped improve the
disconnect detection time down to about 8 seconds. This is still causing some
issues in particular with call progress enabled in * we are having a few
disconnects while calls are in session (about 2 reported in first 5 days of use).
I have talked both to
2003 Oct 16
1
CallerID not passed to Sprint & Verizon Cellphones via XO PRI
Hi,
I have an odd problem where when a call is made to any landline phone the
callerid number shows up on the caller id device with no problems. However
when I call a cell phone from Sprint or Verizon it always shows up as
unavaliable. I've tried multiple cell phones from each carrier. Though
today I called a t-mobile phone and the callerid came through fine.
Is this an * level problem
2006 Mar 27
2
FXO without answer supervision
Simple question that google hasn't helped much with (likely poor search
terms)
I just installed a Sangoma A200 with overall good results. Initial
tests with both
incoming and outgoing calls were very positive. Until I made a normal
call that
lasted more than 30 seconds.
I setup the FXO with kewlstart signalling, and the outgoing call is
never registered
as 'Answered' and the dial
2011 Apr 19
5
Running mailfront under dovecot2.x service supervision
Hello,
I'm trying to run mailfront SMTP (http://untroubled.org/mailfront/) under
Dovecot 2.x process/service supervision
My intention was to utilize the fact that dovecot2.x seems to have some kind
of generic process/service supervision as well as builtin ssl support.
But I cannot get the most simple generic service setup (without ssl) to
work.
Currently running dovecot 2.0.11 on FreeBSD
2004 Jun 09
1
Hang-up Supervision (UK)
Hi everyone,
I've just got my X100P card installed and working but there seems to be an
issue with hang-up supervision.
If I stuff a call out over the X100P card onto the PSTN that's fine. When I
hang up the SIP phone the PSTN call ends. If I receive a call from the
PSTN, it's answered and everything is ok until the remote party hangs up.
Asterisk thinks the call is still active and
2010 Jul 29
2
Disconnect supervision tone detection
Hi,
I am using TDM400 card with 3 fxs and 1 fxo. I am struggling to detect
hangup tone or disconnect supervision tone from my CO. I attached the
recorded wav file which contains my telco's disconnect supervision.
I am using ,
asterisk-1.4.33.1
dahdi-linux-complete-2.3.0.1+
2.3.0
OS => Debian-lenny 5
users.conf
-------------
[trunk_1]
trunkname = pstn ; GUI
2009 Aug 27
2
POTS supervision with DAHDI in 1.4 releases
Greetings,
This may be a dumb question, but here goes. When I was on
1.4.21.2 using Zaptel, I had (at least as far as I could tell) access to
line supervision on my POTS lines using a TDM400P/TDM410P. Since upgrading
to the DAHDI branches of 1.4 (SVN and 1.4.26.1), I've only been able to
duplicate the success of the 1.4.21 functionality once. To test what I'm
talking
2005 Jan 06
1
answer supervision for POTS FXO interfaces
Skipped content of type multipart/alternative-------------- next part --------------
No virus found in this outgoing message.
Checked by AVG Anti-Virus.
Version: 7.0.300 / Virus Database: 265.6.8 - Release Date: 1/3/2005
2005 Aug 18
3
Disconnect supervision question
I'm trying to use Asterisk as a voice mail system and all is going well
except for one issue. When the outside caller drops the connection
Asterisk doesn't sense it. It keeps the line open for about 2 minutes
before dropping it. The FXO is attached to a key system (hybrid PBX).
There was a home-type digital answering machine previously on the same
extension and it was able to sense
2004 Jan 12
0
Disconnect Supervision, SBC, and Adit 600
Can anyone help me with the term that SBC uses to refer to disconnect
supervision? I have an Adit 600 channel bank which has helped improve the
disconnect detection time down to about 8 seconds. This is still causing some
issues in particular with call progress on we are having a few disconnects while
calls are in session.
I have talked both to some local phone contractors and SBC directly and
2004 Aug 28
1
UK Disconnect supervision with TDM400P
Hi
I know this gets covered fairly regularly, but I've had a search through the
archives and can't find anything dealing with this specifically - apologies
if I've missed it though.
I've got a TDM11B with the fxo port plugged into a standard UK BT PSTN line,
loading wcfxs with OPERMODE=UK. All's working well, except if I get an
incoming call through my bt line, and the
2005 Mar 23
1
Wilcard X100P doesn't hang up when in Voicemail() and calling party hangs up.
Asterisk 1.0.6-BRIstuffed-0.2.0-RC7k is installed
I have a x100p card and it doesn't detect a hangup from the calling
party when going in voicemail(). My PSTN provider is sending open loop
disconnect (voltage decrease for a given moment of time). Actually
Progress Detection is HIGHLY EXPERIMENTAL so it should not be required
to fix this problem. I wonder if disconnect supervision is the