similar to: Subject: Re: Analog FXO Woes Continue

[resend in plain text format] > On Tue, 2004-12-07 at 09:34 -0600, asterisk-users- > > request@lists.digium.com wrote: > > > I've been struggling with a test * install for a couple months now in a > > > small office and am just about ready to give up on it. It's not that the > > > system itself is a problem. I've got everything (attendant,

I've been struggling with a test * install for a couple months now in a small office and am just about ready to give up on it. It's not that the system itself is a problem. I've got everything (attendant, voicemail, FXS extensions, Cisco and Polycom hard-IP phones, and 2 VOIP carriers) working except for the frigging analog FXO interfaces. These things are driving me completely mad.

Hello, I have found a "bug", I think in the way TDM400P cards handle FXO interface disconnect/re-connect problems. Normally I do keep all the wires connected from my CO / PABX quite securely, but I had a need to re-route the cable from one side of the desk to another, and I simply disconnected the RJ-45 connector and plugged it back in. THIS PROMPTLY RESULTED IN VERY VERY SCRATCHY AUDIO

I'm replacing a Merlin for a client and they have a PagePal Intercom that I would like to reuse. Here is what I know about it: It has a screw-down wires that goto rj-11 (This was told to me over the phone) that went into one of the Merlin ports. I tried bring it up with fxo_ks and fxo_ls (assuming it was analog and autoanswered) but no luck. I would be happy to replace if anyone knows of

hahahahahahahahahahahahahahahahaha!!! Sorry, I'm a bit slap-happy...been fighting Win2k/APW problems ever since I upgraded to 2.2.3a. Still having problems >2.2.4-pre and now 2.2.4. I have a workaround, sort of...set disable spoolss=no, install drivers for the HP printers; then set disable spoolss=yes. Add "use client driver=no" on each of the HP printer entries. Add

I installed the printer patch on 2.2.4 on my Linux 7.3 box, reconfigured it (I think I did things in the correct order:configure,make realclean,run patch,configure,make,sh.makerpms.sh), created a new rpm, uninstalled the old samba, reinstalled the new rpm, fixed the conf files, reloaded samba and now my printers appear as "HPLASERJET on _smbserver". HPLASERJET is queue name which is

Hi, Can anybody with previous experience with it guide me on how to setup asterisk with analog e&m to connect it to an old style e&m system which uses 4 pair cables on RJ 45 jacks. All the analog cards I know of use RJ 11 jacks. And there is no choice of modernization of the customer equipment. Cable pin out are as follows: 1. M lead 2. E lead 3. Tip1 4. Ring 5. Tip 6. Ring1 7. SG 8.

I am using Verizon FIOS to my home. I subscribe to a 5 MB down 2 MB up data package. I continue to pay for a standard voice line in addition to the broadband connection only for local calling, fax and emergency 911 use. The way it works is that the fiber optic connection is terminated on the house via an ONT (optical network termination). The ONT can provide connectivity for three types of

> I looked at your network diagram. Try checking the configuration of the > Ethernet ports on the firewall and the Asterisk box. Make sure they are > set to auto-negotiate and not set to a fixed speed and fixed duplex. > I have found in the past that if one end of a link is expecting auto- > negotiation (as the switches probably are) and the other end is expecting > a fixed

System is built on a SuperMicro motherboard with Serverworks chipset, IRQ is not shared. Have a dialplan that worked for 8 months without errors, tried reverting to older release then upgraded to 1.0.3 stable release, currently running on fedora core 1 kernel 2.4.22-nptl.2199 (have tried plain jayne), telco says "it's not us", HDLC abort seems to occur when when a Zap channel hangs

Ok guys I am having some issues with Samba via ADS. I went to browse a share I setup on my Linux box and it prompted me for a username and password. This did not work but I found this in the log.winbind [2003/05/13 16:15:56, 1] nsswitch/winbindd_util.c:rescan_trusted_domains(168) scanning trusted domain list [2003/05/13 16:15:56, 1] libsmb/clikrb5.c:krb5_mk_req2(267) krb5_cc_get_principal

hello all, I have a DID from nufone, transported via SIP to my * box, and even though i'm using rfc2833 DTMF i'm still getting double digits and all sorts of other stuff... sip.conf is as follows: [general] port = 5070 ; Port to bind to disallow=all ; Disallow all codecs allow=ulaw allow=alaw allow=ilbc allow=gsm dtmfmode=rfc2833 register =>

Thought I would post this experience to the list so it's archived for posterity... My company is deploying Asterisk-based PBX's to all of our branch offices. Each office has 2 analog Voice lines and a fax line. We didn't want to go to the expense of using TDM400's in the servers (which run asterisk and Hylafax) so we opted for 2 X100P cards in each box. So far they have

Hi Yair, Please let me if you managed to fix the DTMF tone issue, which you were experiencing couple of months ago. If not can you share any advancement. I'm currently experiencing the same issue, I can make outbound calls but DTMF will not work when dialing IVRs. My configuration is asterisk@home 1.5, registering to Voip provider (Symbio), codec is g.729 and dtmf mode is set to rfc2833.

Hi, Using Zack's -shared replacement posted earlier, addons now compiles. For some reason though, when trying to load it cannot find cdr_mysql.conf even though it's in the /etc/asterisk directory as it should be. Anyone with any ideas? There's still references to _i386 files that are probably incorrect as well. Thanks Rob console messages: apsvr1*CLI> reload Mar 23

I sent in a patch a week or so ago for a problem a customer of mine was seeing when trying to connect to their OpenVMS system with an 3.8.1p2 OpenSSH client (running on a linux box or in cygwin) and trying to login to an account who had an expired password. The problem continues although now it has nothing to do with what my patch handled as they have since upgraded their SSH software on the VMS

My telco used cat5 as well for the demarc to CPE. It's also with noting that many channel banks, such as my Atlas, and zapata.conf itself also have parameters to allow you to tune the gains to compensate for cable signal loss. I've never had to touch them, and my CPE is about 300 feet from the PRI demarc (with an ordinary Cat5 cable connecting them)

Hi, Being new to R I'm asking for some advice on how to optimize the performance of the following piece of code: > alpha_c <- function(lambda=600e-9,alpha_s=1e-14,N=400,spacing=1e-7){ > > k<-2*pi/lambda > ri<-c(0,0) # particle at the origin > x<-c(-N:N) > positions <- function(N) { > reps <- 2*N+1 > matrix(c(rep(-N:N, each = reps), rep(-N:N,

List, Im a Cisco certified Network guy with little telecom experience (BRI/PRI at the time) so please forgive my terminology. I am showing interest after the Network World SHSU October 4 article. We have 3 offices (Hub-Spoke T1 Frame relay to the remote offices(Data & voice on separate T)). Each office currently does their own thing for telecom. Our Main(HUB) office currently has 14 channels

Hi, I''m trying to get up and running with StoryRunner. I have a story that looks something like the following, but the call to mock_model produces the exception listed below. Am I just misunderstanding the concept? Are mocks not meant to be used in stories like this? Or is this a bug? Changing @user to be an actual AR object makes things run without error. ENV["RAILS_ENV"] =