similar to: DTMF via PSTN to * to IAX to * challanges.

Well here is something simple, well I think it is for the smarty's out there :) I got a connection to freshtel and want to get the iax working. I have config'ed up iax.conf with the register line and get in return in the cli> -- Registered to '202.168.7.130', who sees us as 203.29.98.221:4569 So that appears to be connected. When I call the DID number I get the Voicemail

Ok I have a challange that I can't seem to find a way to fix it. My Voicemail in * timesout after 30secs without fail everytime no matter what I do. I have incomming calls comming in through Freshtel IAX2, if it goes to SIP extension when it is online it can hang on for what ever time the call goes for. If however it goes to the Voicemail it will timeout at 30sec and I can't seem to

Ok I have spent the last week working on getting my small PBX to work. I will in the end only have 4 SIP extensions being either softphones of IP phones. Currently only 1 SIP config for testing. And at the this point it should be all fairly easy with all inbound and outbound to PSTN will be going Via Firefly/Freshtel.net in Australia via IAX. Inbound does work in it's current basic state.

I installed G729 from Diguim and I was expecting the sound quality on my i686 machine to be better than gsm. Compared to gsm, G729 sounds closer and a little robotic. Is this what is supposed to be or am I missing something? I am interested in G729 because the internet in my country is very expensive and I want to save every bit possible. I want to use G729 because it takes less bandwidth for

With a service like http://www.freshtel.net/?show=home that uses IAX and has servers in Australia, is it possible for the audio streams to take a different path than the call setup and control? In other words can it work like SIP with canreinvite where the two endpoint negotiate audio streams between themselves rather than though the FreshTel server? Thanks

Just working on Configing up Voicemail and now that I have got it working and configed and answering the way it should be I have another challange. on the * CLI> I get this -- Recording the message -- x=0, open writing: /var/spool/asterisk/voicemail/default/6001/INBOX/msg0000 format: wav49, 0x8133390 -- x=1, open writing:

I am running * 1.0.5 and have been having lots of problems with outgoing calls and their sound quality. I am using ULAW for the codec and sixtel for termination. Basically the problem is that portions of the call seem to be lost and replaced with silence. Sometimes I can't hear the person talking othertimes they can't hear me. This situation comes and goes throughout the call. Bandwidth

I've configured Asterisk 0.7.2 to work together with Cisco ATA186 (SIP,G.711. RFC2833) and OpenPhone (H.323, G.711). But there is an issue while calling from ATA186 to OpenPhone via Astrisk - when I press any key on analogue phone connected to ATA, Asterisk shows following message: -- Executing Dial("SIP/519-3781", "OH323/62.213.36.100|20|Tt") in new stack --

Okay, I've read as much as I can, and I think i've followed instructions, but I'm still having problems with * and firefly... I can get outgoing to other freshtel working, but not incoming (I get the "not available" voicemail), or outgoing to landline. I'm using the debian asterisk package (0.9.1-RC1-4) My iax.conf has in general (under my FWD register, which

Hi, I'm having some problems getting calls to go out via freshtel. There dosn't seem to be any specific information on how to get it working anywhere. The only information I've found is here: http://www.voip-info.org/wiki-Freshtel and that dosn't give you any idea of how to actually get it working. I've tried adapting information from other IAX2 provider examples but have

Hi helpers, I seem to have a problem of intermittent DTMF tones being played during a conversation. Eg: Extn 100 takes an inbound call and all is fine. Except, at an undetermined time the person on extn 100 will here a DTMF tone for no apparent reason (it's not the caller pressing buttons). The caller doesn't hear the tone - only the called person. The call itself progresses normally.

It is not clear how exactly g729 pass-through can be enabled. I have a SIP call off a gateway come into an Asterisk menu, and then I send the SIP call to another SIP gateway using Dial(). Even though codec preferences have g729 listed first, it never gets used. Both gateways have separate peer entries in sip.conf, and both have canreinvite=yes set. Can Asterisk change the media type during

This post is simply documenting a spouse-friendly way of using the spa-3000 as both a fxs and fxo port for basic soho environments in the US, allowing asterisk to participate as needed/wanted. All home phones are connected _only_ to the spa-3000 fxs port. The incoming home pstn line is connected _only_ to the spa-3000 fxo port. Defined Line 1 (fxs) to register with asterisk via sip (extn

Greetings! to all Now, with some hard time and help from many genurous people's in the list, I have come to this point with my TDM20B card & my teliax's IAX2 account. I hope someone may help me with this issue mentioned below. I have already selected my codec as gms in my iax.conf as well as in teliax's "my account page" but still i have the same error when I attempt

Hello All, Anyone here has experience of accepting a ilbc call and sending it on g711 or g729 I am having problem in VOICE , call goes though but there is no voice. Senario: Call is coming in from Machine A to Machine B, sending to Machine C Machine B is an asterisk box, transcoding it from IBLC to G711 and g729. Problem: Voice is not appearing on the sip user sitting on machine A Already

Ladies and Gents.... Please be patient as I try to explain what I am trying to achieve.. I have a PSTN line and a Freshtel account, what I want to do is have the PSTN line as the first choice for outgoing calls for local calls and Freshtel as the second choice. The problem is that it's easy enough to set up both individually but how do I get the "second choice" drop the leading

Hello everybody, my * box is connected to gnugk with H323 channel. If I call from an H323 EP to SIP EP (GS HandyTone or Xlite), when callee is picking up, audio start but noisy (scratch) , then became ok for callee (SIP EP) but still scratching on H323 EP. Now I stop/start asterisk, call from SIP to H323 EP and it's ok. And from now, it's also ok when H323 EP call SIP one's! No

I found version 2.0.0 of Firefly on the Freshtel site, but it only has the network setup options for the Freshtel network, despite the final statement on the page http://www.freshtel.net/firefly/download/ that says: ----------------- Standalone SIP / IAX mode: If you want to use Firefly on our network (with your own voicemail etc.) you will need to register a Firefly number. However, you can

Hi, I was running asterisk 1.0.7 but we've upgraded now to CVS-HEAD. I've noticed this.. and several people have commented that audio quality seems to have gone down hill. Just going phone-->asterisk-->PRI. I've not changed the configuration files during the upgrade. sip.conf is: allow=ulaw allow=ilbc allow=g726 allow=g729 allow=g723.1 And all the phones had been using

We have another 500 beta openings in the SimpleConnect beta. SimpleConnect is a service for you to make IAX/SIP calls from * or any IAX/SIP agent. Beta participants get free calls to anywhere in the United States and Canada. If you want to become a beta tester, just go to https://secure.simpletelecom.com/order/ . No credit card is required. We're looking forward to your feedback. Sean