similar to: Recomended ISDN for Asterisk ?

Displaying 20 results from an estimated 1000 matches similar to: "Recomended ISDN for Asterisk ?"

2005 Jan 23
4
Florz patch for zaphfc
Has anyone had any success using the Florz patch for zaphfc ? I have a * system with 2 HFC cards which is working fine with 2 PTP ISDN lines however the users are complaining of crackles on the line which I am assuming is related to the IRQ issues raised by Florz. I have tried to use the patch but it errors trying to patch zaphfc.h Any help would be appreciated. Regards, Stuart -- No virus
2005 Jan 25
3
Bristuff ZapHFC and Loosing D-Channel
Using the latest(?) bristuff (Asterisk 1.0.4-BRIstuffed-0.2.0-RC3a) I have problems with loosing the D-channel. Most of the time, after the message "PRI D-channel down" it only takes a second or so to come back up, noted by the message "PRI D-channel up" However, today most of the time the D-channel stays down. Calls come in, but can't be answered. Does anyone know
2004 Dec 27
3
how to debug frame slips?
Hi, I'm running into issues receiving faxes which, from what I have read, may be caused by frame slips. While I can find many posts saying to investigate it, I can't find any that describe *how* to debug the problem. Tried searching this list as well to no avail. Any pointers would be greatly appreciated. FYI, I'm running wbel, AMP 1.04, spandsp 2pre4. Faxing to a pstn on a
2004 Dec 14
1
ISDN HiSax: unauthorized source code changes
Hi After modprobe hisax type=35 (Billion HFC PCI) on a Xorcom Rapid ISO I get: HISAX Dec 12 16:25:35 localhost kernel: HiSax: Linux Driver for passive ISDN cards Dec 12 16:25:35 localhost kernel: HiSax: Version 3.5 (module) Dec 12 16:25:35 localhost kernel: HiSax: Layer1 Revision 1.1.4.1 Dec 12 16:25:35 localhost kernel: HiSax: Layer2 Revision 1.1.4.1 Dec 12 16:25:35 localhost kernel: HiSax:
2004 Apr 26
3
dtmf tone clamping in calls to external ivr
Hello, I'm having trouble working out how to send DTMF tones to an external IVR. My system has an analog phone connected to a TDM400P card, a SIP software phone (Zultys LIPZ4) and is connected to a BRI in Australia with a NETjet-S card. I'm using ISDN4Linux and a 2.4.25 kernel patched with the ISDN audio patch from Traverse (which allows the card to do voice). DTMF works fine between
2005 Jan 10
4
audio delay ISDN
Hello all. Since half december we are trying to implement * as our primary PBX. We had a test machine running with 2 sip phones and a single ISDN card. Since this was working ok, we installed * on our main Debian server. Some specs: P4 2.8 Ghz HyperThreading 512 MB RAM Debian Sid updated every week. Linux 2.6.9 vanilla kernel (not the debian package) 1 Intel Pro 100 nic for internal network 2
2005 Sep 27
1
R: Best drivers for HFC-S ISDN cards
Mine is very similar: i don't have echocancelwhenbridged=yes because it seems work only on TDM, is it ? And in Italy, I often have set pridialplan = unknown About echo I have some problems, but only at the beginning of the call. After 3-4 seconds the echo became almost null, specially with snom 190; with pa168s and ywh10 I have again some problem, the echo come up also after 1 minute of
2005 Jan 27
2
Results of MCD estimators in MASS and rrcov
Hi! I tested two different implementations of the robust MCD estimator: cov.mcd from the MASS package and covMcd from the rrcov package. Tests were done on the hbk dataset included in the rrcov package. Unfortunately I get quite differing results -- so the question is whether this differences are justified or an error on my side or a bug? Here is, what I did: > require(MASS) >
2010 Jan 16
4
Howto regret blind transfer?
Hi, Is it possible to "regret" blind transfer while its ringing (not answered)? Thank you! Best regards HB
2004 Jul 07
4
HFC- Colongne TE Mode
Hello There, I am trying to get Asterisk to work with Billion ISDN Adaptor, But i couldnt get isdn4linux to work. I am pretty new with isdn card but this is the only available option here right now , I've looked at this post and found that the author has been successful in installation of the same card. Can someone please help me out by giving the author's email address , so i can
2009 Dec 12
3
Random DTMF tones generated from speech in conversations
Hi, My Asterisk systems runs like a dream with mISDN, SIP and even and old Digium board. But have almost in every conversation some irritating DTMF being generated. The seems to be just as often from all trunks but are worse if noise load speaker in other end. Any good advices? Where to look for forgotten DTMF detection settings? Thank you! HB
2008 Oct 27
3
Door phone
Hi, Is there an affordable HW solution to do a door phone on *? I do not mind using the solder iron to modify an existing door box. Thank you! Best regards HB Norway
2009 Dec 13
1
Random DTMF tones generated from speech
Thank you, very interesting! As I understand the Digium card is used as a interrupt source for Asterisk? Is there a diagnostic tool available ? Anybody else experienced a simmialr problem? Thank you! HB > From: > covici at ccs.covici.com > Date: > Sat, 12 Dec 2009 19:04:23 -0500 > To: > Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users at
2005 May 25
7
zaphfc: empty HDLC frame or bad CRC received
Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from
2004 Jul 26
6
Can't dial SIP<->EuroISDN (HFC-S based PCI ISDN card): Unable to create channel of type 'Zap'
Hi, I'm trying to set up an Asterisk pbx based on a Fedora Core 1 Linux box (customized kernel version 2.4.24). I want calls from my SIP soft-phones to simply be dumped onto the PSTN line via a BRI (EuroISDN). I have a cheap HFC-S based PCI ISDN card connected to the NT1+ interface, so I need zaphfc. I've read everything I've found at www.voip-info.org, then I've downloaded the
2003 Apr 07
6
ISDN4Linux problems
Hi, I try to use ISDN4Linux drivers with Asterisk. In modem.conf i put /dev/ttyIO. Everything is OK when i lauch asterisk but, when i call Asterisk nothing happen. Someone can help me ? Rattana -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20030407/13e78d8e/attachment.htm
2001 Apr 26
2
not able to download WinNT version (PR#922)
I keep clicking on the WindowsNT link and it keeps extending the path name... is something wrong? thanks -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- r-devel mailing list -- Read http://www.ci.tuwien.ac.at/~hornik/R/R-FAQ.html Send "info", "help", or "[un]subscribe" (in the "body", not the subject !) To:
2003 Apr 01
4
low-cost * (newbie question)
hello all i'm interested in setting up a small pbx using asterisk and the primary goal is keeping the cost down. the general layout of the net is as folows: * 4 phone lines (2x isdn+ 2x analog) [or 2x isdn + 1x analog, as one might be put aside for a traditional phone/fax with no fancy stuff] * a server box * several client hosts (all linux with x) currently, the isdn lines are unused (to
2003 Apr 07
3
isdn config
Hello, i have asterisk with 2 internal isdn cards - handled by isdn4linux and i need to setup whol system like this route some call beggins with 0 or 00 - long distance through first card, route calls to mobile network via second card ( tehere is isdn gsm gateway connected).how i can do this using only isdn4linux (/dev/ttyi) ? regards Marian -- SUNTEQ s. r. o. Bojnicka cesta 35 # Prievidza
2009 Nov 11
2
Best practice to set up 4 line phones
Hi, I would like some advice from you on how to configure a multi line phone the best way! So far I have given the phone 4 sip accounts one for each line, this is a lot of work and gets messy. Is it a better way to do this? Thank you! Best regards Helge-Bj?rn