similar to: PolyCom MWI Chirp issue

I am wondering if anyone could help me figure out how to turn down the volume on all the dial tones, indications, etc.. and especially the call-waiting CHIRP! I don't want to change the txgain and rxgain because they are working at levels that I would like. However, when voice conversations and voicemail recordings are at good levels then the dial tones, busy tones, etc are way too loud.

Hi, What is out there in terms of SIP enabled handsfree speakerphones? Looking for something that works well and also fits a low budget. I am used to using a Cisco 7940. It is a great phone but a bit expensive. Thought about the Polycom SoundPoint 300 until I realized that it does not include speakerphone functionality. Thanks, Adi

Hi all, Configuration: Analog phone connected to TDM400p. I'd like the phone to give a half-ring (chirp) periodically when there is a message waiting. Can this be done? How is it configured? The visible "Message waiting" indicator and the stutter dial tone are working fine, but are not sufficient for me. Thanks!

I'm trying to solve a homework problem using R. The problem gives a list of cricket chirps per second and corresponding temperature, and asks to give the equation for the linear model and then predict the temperature to produce 18 chirps per second. So far, I have: > # Homework 11.2.1 and 11.3.3 > chirps <- scan() 1: 20 2: 16 3: 19.8 4: 18.4 5: 17.1 6: 15.5 7: 14.7 8: 17.1 9: 15.4

I was wondering if anyone has had a problem with an initial chirp from asterisk after dialing an outside line through a TDM400? I am using 3 polycom 500's and it happens regardless of what phone I am at. So I was thinking maybe it was an issue with asterisk or the uLaw codec? Thanks. Jared Armstrong -------------- next part -------------- An HTML attachment was scrubbed... URL:

Does anyone here have any "feel" for the "Battery disconnected" and "Battery reattached" log entries? The rebooting came as a result of me turning off modems, router, external drives, monitor, cordless phone and finally, the computer, trying to locate a quiet but annoying "chirp". The "chirps" stopped when I tilted the UPS to look at the front

Hello, i try to send out a sms, but with no success. The trunk is a E100P, and the sms should go out to the Telekom SM-SC. What i want to to at the first run is, sending out a sms when a certain number is dialed. I tried: In extensions.conf: exten => 35953,1,SMS(${TRUNK}/9350193010,,0179NUMBER,"Hi there") exten => 35953,2,SMS(${TRUNK}/9350193010) exten => 35953,3,Hangup

Hello, I faithfully followed the instructions from: http://www.voip-info.org/wiki-Getting+MWI+on+Polycom+Phones+to+work+with+Asterisk but still the message waiting indicator doesn't flash when a message is waiting. There is a brief intermittent chirp but nothing more. Using latest firmware 1.4.1 Thanks for your suggestions,

Hi, I have lookedaround and don't see this anywhere. Is there a way to tell the ip500 to not make the aural MWI blips?

incominglimit is already implemented for SIP. Just specify under the endpoint how many incoming connections are allowed. For example, [cisco] type=friend username=cisco secret=blah nat=yes ; This phone may be natted host=dynamic canreinvite=no ; Cisco poops on reinvite sometimes qualify=200 ; Qualify peer is no more than 200ms away

I just upgraded a box to 1.2.3 this morning after encountering the issues noted earlier on the list. Everything is great. In fact, a LOT better. In the past few weeks, I've been battling with BV to address dropped outgoing voice packets (the flipside is that I haven't experienced this with other providers during tests), and an annoying mechnical 'chirp' at the start of a call.

I read through the "Writing R Extensions" and the "Debugging in R" website (http://www.stats.uwo.ca/faculty/murdoch/software/debuggingR/), looking for some hints about how to solve the issue of debugging problems encountered during the "R CMD check" process, but nothing seems to be mentioned about addressing issues encountered. Specifically, I am working with the R

Does anyone on-list have an example of working SIP config using Nuvio? I have a byod account that I'd like to run into my Asterisk server. Thanks, Michael

Dear helpers, When I use the function cgt of library Rwave, the time axis of the plot is always on the [0,1] scale regardless of the original time. This happedn when I tried to reproduce some pictures of "Practical Time-Frequency Analysis", e.g. Figure 3.5 and 3.6 using the codes provided in the book. But the figures of the book display the real sampling time using the same codes.

Well, Once upon a time, I had problems receiving callerid, and then one day, Mark was logged into my asterisk box helping with something else, and I asked him about this, and he showed me a nice tweak to some source file that made it work. Some time later, I must have done hundreds of CVS updates, and along the way, lost the above patch (one liner) and so callerID hasn't worked for a long

Hi Jean-Marc, I use the resampler to convert various sampling frequencies to 48 kHz on my Blackfin platform (fixed-point) 48K -> 16K speex -> 48K chain does not sound very good compared to plain 16K. But the main issue is when processing loud signals, I have truncation (and not clipping/saturation) I could hear it and see it with various music and speech messages. See example.png. I also

Hi, I have installed a CCNP test application that came with a CCNP book but the actual text of the questions is missing. The wine version is 1.2.2, the OS is xubuntu In the quiz preferences the two font options are arial and times new roman I am guessing that it just can't find these fonts, but i am not exactly sure where i should be putting them. I have installed MStruetype fonts but

client with my asterisk. If i am wrong, please let me know On Wed, Jan 7, 2009 at 4:43 PM, Rodolfo Alcazar Portillo < rodolfo.alcazar at padep.org.bo> wrote: > Missed the thread, sorry. Gizmo5.com has some blackberry SIP clients. > Could be what you want. > > Greets! > > Am Mittwoch, den 07.01.2009, 16:07 -0500 schrieb Eric Moniz: > > TianLun, > > > > I

My friend somehow managed to get a BDP-95, even though the hardware isn't scheduled to ship until March. The problem is that the manual makes no mention of FLAC, at all, and only the web page claims to support the format. Playback of flac seems to work, but files from one online vendor work flawlessly while files from other online vendors have strange glitches that sound like a

Hello Family, My RedHat-7.2 box prints perfectly to an Epson777 color injet printer which I gave an IP address via a mini printserver attached to the back of the printer. I have a Windows2000 computer hooking into the same RedHat-7.2 box via Samba-2.2.2 fine. I have not been able to get my Windows2000 box to print to the Epson777 color injet via Samba. [question] Since Linux already