Displaying 20 results from an estimated 900 matches similar to: "Outbound E&M?"
2003 Dec 16
1
DISA - Zap/DTMF Problem
Hi guys,
I am trying to use DISA. The scenario is - I call my home number (where
X100P seats) from mobile phone, enter the password, enter international
number and get connected via voiptel. It works perfectly when I call
extension setup with DISA from X-PRO SIP phone, but when I dial into
Zap, It seems that it does not detect DTMF tones. Here is a log and
config files
Please help
2003 Oct 06
1
chan_zap.c - echo cancelation getting in the way of dialing????
It seems consistant after dialing dozens of times that the call that
doesn't go through is the one the gets the log message "No
echocancellation requested" (chan_zap.c) and the "Scheduleing timer"
(channel.c) in the middle of receiving the DTMF tones.
I'm now using the T400P card last week very simular problems the the T100P
(although I think I was actually loosing
2004 Nov 28
4
PRI Dialing failure?
So I reached the point where my PRI is accepting incoming calls, but I
cannot dialout. I must be doing something stupid, but I can't figure it
out. The Asterisk box is sitting between the Mitel and the phone company,
and has PRI lines to each. Asterisk was built from CVS r1-0
Log for a call from mitel heading outbound:
-------------------------
-- Accepting call from '' to
2004 Dec 22
2
txfax failure
Hi list,
Just installed spandsp. In my limiting testing, I have an issue on a
Philips fax machine (HFC21) directly connected to my * server through
TDM400, reception with rxfax works fine, but txfax always fails. Below
is a transcript of failed transmit.
This is with asterisk-1.0.3 (with native moh patch but I don't think it
is the source of the problem). I already tried libtiff 3.5.7,
2005 Jun 01
1
rxfax problems - cont.
Well, my faxes passes through asterisk successfully, however I still have
some problems about fax reception by rxfax.
The softfax answers, and negotiates transmission, however then as some stage
of communiation something is wrong.
But I have nothing more but this log:
Jun 2 00:10:21 DEBUG[16900]: chan_zap.c:4242 zt_read: DTMF digit: * on
Zap/10-1
Jun 2 00:10:22 DEBUG[16900]: chan_zap.c:4242
2003 May 22
2
new DTMF tones
I just loaded from CVS this afternoon and in the debug output I see...
DEBUG[76820]: File chan_zap.c, Line 3254 (zt_read): DTMF digit: m on Zap/16-1
DEBUG[76820]: File chan_zap.c, Line 3254 (zt_read): DTMF digit: u on Zap/16-1
I knew about DTMF 0-9, A-D, *, and #, but I didn't know about m and u :-).
2004 Oct 05
1
difference between dtmf digit 8 and 9
Hello,
this is an example extensions.conf.
[default]
exten => 500,1,Answer
exten => 8,1,SetGlobalVar(firstdigit=8)
exten => 8,2,Goto(process,s,1)
exten => 9,1,SetGlobalVar(firstdigit=9)
exten => 9,2,Goto(process,s,1)
I call extension 500 and send dtmf digit 9. This is printed to the
CLI:
-- Executing Answer("Zap/20-1", "") in new stack
-- Accepting
2006 Feb 19
2
spandsp 0.0.2pre25
Hello,
Is anyone successfully using spandsp 0.0.2pre25 with either asterisk 1.0.x or
1.2.4? I've built a Gentoo ebuild for this version of spandsp and app_rtxfax,
and it builds, but I'm not having any luck getting it working. 99% of my test
faxes fail. Reverting to 0.0.2pre20 yields a much higher success rate.
I've bumped the console debugging level in logger.conf to include debug
2003 Nov 18
0
Bad DTMF detection
We're still having problems with DTMF detection on our X100P cards.
Incoming callers that hold down the "1" button for too long are being
connected to extension 11. One would think fat fingers were uncommon,
but it happens to alot of people.
I suspected this was related to our having to increase the txgain, but I
tried turning it down with no effect. I also tried disabling the
2004 Aug 25
3
Fax detect
I have found that fax detection is returning an error saying that no fax
extension is present when I have defined one.
The console returns this error:
Aug 26 10:58:41 NOTICE[1112745536]: chan_zap.c:3989 zt_read: Fax detected,
but no fax extension
extensions.conf has:
[default]
exten => fax,1,Hangup
exten => fax,2,Congestion
exten => fax,102,Congestion
exten => f,1,Hangup
exten =>
2003 Dec 17
5
ALL incoming Zap channel calls are getting picked up as FAX calls!
All,
I upgraded my asterisk setup from CVS on or about 12/15. Suddenly, *all*
of my incoming calls are coming up as FAXes. I had to disable my fax
extension because every call to my POTS line was getting redirected to my
FAX machine. After removing the FAX extension, if I call my POTS line from
my cell phone, I get the following:
*CLI> -- Starting simple switch on 'Zap/1-1'
2003 Nov 18
4
Help with Warnings
I'm trying to clean up some notices/warnings that are repeatedly logged
in *.Any Help would be appreciated as I'm not sure of the cause
/solution.
Here are the errors:
Nov 17 15:53:38 WARNING[1217602880]: File chan_zap.c, Line 1321
(zt_call): cidspill already exists??
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
/* Don't send audio while on hook, until the call
2005 Mar 24
2
Fun with CAPI
Hullo :) Can someone help me untangle a bit of a mess?
I'm trying to set up a demo * server to show off how useful it can be to our
business (as an IVR system and VoIP backup if our ISDN30s fail). I've not
been able to get NT mode working with our InterTel Axxess PBX, so I've
resorted to using normal TE mode and working on the basis the people dial one
of the ISDN BRI extension
2004 Jan 15
4
People detected as fax machines
A caller to me was this afternoon detected as a fax machine:
Jan 15 15:31:17 NOTICE[41997]: File chan_zap.c, Line 3564 (zt_read): Fax
detected, but no fax extension
... and then redirected to voicemail. An extract from extensions.conf is
attached below. Is there any way to stop * even considering an incoming
call on a line as a fax call?
Iain
bell]
include => mailboxes
include
2003 Nov 25
2
zt_rec: Unknown error 500
I have a number of Zap/ extensions defined in a queue with ringall
strategy. When this queue is called sometimes Asterisk seems to think
that one of these channels is busy, while it is NOT. The following is
shown on the console:
--Called 44
-- Called 36
-- Called 41
-- Called 35
-- Called 38
-- Zap/44-1 is ringing
-- Zap/36-1 is ringing
-- Zap/41-1 is ringing
2004 Jan 08
3
Asterisk hanging?
Hi,
I compiled and am running the latest CVS but strange things are now happening..
it looks like asterisk is randomly declaring my calls to be fax calls,
complaining and then sending the calls into a black hole... if I hangup the
calls below (soft hangup) asterisk locks up and I have to kill the process.
NOTICE[21526]: File chan_zap.c, Line 3520 (zt_read): Fax detected, but no fax
2005 Jun 28
2
Trying to get *8 call pickup to work
I'm using the Debian Sarge package of Asterisk - 1.0.7 + bristuff. When
I call from a zap channel or a SIP phone to another SIP phone, then dial
*8 from a third SIP phone, I get 503 Service Unavailable on the
third phone and I get this at the Asterisk console:
Jun 28 09:01:24 DEBUG[16774]: res_features.c:1709 ast_pickup_call: No call pickup possible...
Jun 28 09:01:24 NOTICE[16774]:
2003 Aug 25
1
chan_zap.c zt_rec: Unknown error 500
Hi all,
I'm using asterisk CVS-08/14/03-22 on a box with a digium T1 connected to a
channel bank and a digium E1 connected to the PSTN.
I get occasional warnings from asterisk:
WARNING[37909]: File chan_zap.c, Line 3197 (zt_read): zt_rec: Unknown error
500
This happens mosttimes in a loop like this:
[netland_helpdesk]
exten =>
2005 Mar 11
1
Incomplete incoming fax using spandsp 0.0.2pre10
Hi,
I have successfully compiled spandsp 0.0.2pre10 with * 1.05 which can accept
inbound fax calls. However, all fax received are incomplete (the first 10%
of an A4 page is fine, the remaining is either missing or garbled). I
suspect this is due to 'training error' (see below) which, according to
Steve Underwood's postings, cannot be resolved further. I wonder if it would
help to
2004 Aug 04
0
Configure E1 PRI
After sometime I got my E1 PRI configured correctly in /etc/zaptel.conf
and I now don't see any alarms on the E1, but I can't still dialout
correctly, I enable every debug that I could though of and this is what
I see:
At the end the D-channel is down and I cannot even try to connect
another call because it tell me that the zap channel is unavailable ,the
other this that I notice is that I