similar to: Stanaphone down?

For some reason I now seem unable to control which codec is chosen. The problem happens with outgoing calls to Stanaphone. Even if I chose disallow=all and allow=ulaw as the only codecs it connects with GSM. Has anyone else got problems with these settings? Any suggestions? As I recalled it, such a setup would not establish a call if the ulaw-codec was not offered by the provider. Stanaphone has

I am trying to get Asterisks to connect to our StanaPhone so that I can use it to route my outgoing PSTN calls to. We have a free account and if I can get this working are willing to pay for an actual minutes with them. Here is what I have in my sip.conf: [stanaphone] type=friend secret=pAsSwOrD ; skewed for this message. username=3475341914 host=sip.stanaphone.com

Sorry if this comes thru twice, I had the wrong account selected to send the first time... Callers to the number get ringing, I get stuff in my asterisk console, and it calls my softphone and ata, but answering either gets silence, and the caller gets the ringing stop, if they wait ages they get the stanaphone voicemail. I have had the account for ages, and it never has worked, other sip

I see that stanaphone is not accepting new customers. Does anyone know if they are doing ok? I have a number with them and would like to start redirection people before it gets canceled on me if they are having trouble.... thanks Todd

I'm looking for some help in how to keep asterisk from doing this. If we loose Internet or routing to our upstream provider even for only a few short minutes asterisk quickly gives up & never tries again. I have to do a manual reload to get it to register with my sip provider(s) again before incoming calls are accepted. This is really bad as it causes us to loose the ability to get

Hi, I am pretty new to all of this but was able to set up an asterisk server and have been able to succesfully connect to asterisk with x-lite as sip client. I have also connected asterisk to FWD (using iax2) and to voipjet (also using iax2). Now I am trying to connect asterisk to Stanaphone. It has to register as a SIP client but I am not being succesful at all. My asterisk server sits behind a

I have been running Asterisk for years on a machine with a public IP. Most recently, I have been running 1.2.17, from the day it came out, with no (noticeable) problems. Yesterday, I switched over to a new server that is on the same public subnet, one higher than the original server. I built 1.2.17 from source on that machine (as I did on the old server). My firewall on the new machine is

We are having lots of problems with stanaphone. It used to work ok, but now it's terrible. As of this moment, can't make outbound or inbound calls. Anyone has it working? Please provide sip.conf example commands.. Thank you -- Leandro Rzezak leandror@gmail.com -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hello, After much searching of voip-info.org and google, I'm finally giving in and asking the list. The setup I have is this:- Single X100P card in a Debian system Inbound/Outbound POTS line connects to the X100P Sipura 2000 and Budgetone 100 on the LAN 1 Cordless and one conventional phone connected to the sipura Account on Stanaphone.com for eitherbound SIP calls. (I have other SIP

Hello, did you got your issue solved? I am suffering of the same issue.... On 4/28/07, Hadar Pedhazur <hadar@unorthodox.com> wrote: > > I snipped all of the previous data, as I'm trying to "boil down" > this problem to its essence... > > I turned off the firewall for a few seconds, and still got no > audio. For those that will be suspicious, the commands

Hi everybody, I've got a very strange problem: As far as I remember I didn't change anything on my Asterisk side. I have 2 SIP providers to which I can place outbound calls. Today I noticed that outbound calls to provider "inode" fail (and inbound from this provider too). On the CLI I get every 20 seconds following messages: Nov 9 20:01:07 NOTICE[952]: chan_sip.c:5422

Now that I have most everything actually working I've noticed that about every 3-4 days on average..... and at worse... Once a day my asterisk box seems to lose it's registered state with our sip provider and no longer will take any incoming calls. The caller simply hears a fast busy (reorder) If I do a reload at the command prompt all is well for another few days..... What I'm

Hi All, I have just installed Asterisk and am trying to connect it to a SIP account that I currently have with www.voiptalk.org but without any success. Although I know that voiptalk do provide asterisk accounts I don't want to convert the SIP account until am happy that it's gonna work for me. The asterisk box is currently behind a firewall and the following ports are being forwarded

Hi. I have a x100p card installed and also asterisk, but I just dont get asterisk to register with my sip provider (FWD)... when I start asterisk using the following command I get the following messages (first, a lot of messages show up immediatly after starting up: I'read this is normal, then the CLI console comes out and this messages appear): NOTICE[229390]: chan_sip.c:3922

I am receiving this message on my asterisk server and I have commented out 5748150837 in my sip.conf file but it keeps showing this message on the server. Dec 10 07:59:31 NOTICE[30448]: chan_sip.c:5267 sip_reg_timeout: -- Registration for '5748150837@69.25.143.141' timed out, trying again (Attempt #1546) any ideas? -------------- next part -------------- An HTML attachment was

Hi all, I tried searching, so if this has already been discussed please point me in the right direction. On separate occasions I've seen cases where Asterisk boxes will be unable to register with each other via SIP or IAX2 when a Firewall is replaced. I'll describe two different cases. In both we have three offices connected via IPsec tunnels. Case 1: High Availability firewall

I'm going to try and ask this again and keep it short and as too the point as I can while still providing enough info to be of use. PLEASE advise if I am going about this wrong or asking too much. I'm seriously doing my BEST to throughly read the docs and try a bunch of things BEFORE coming here to ask and possibly annoy. If is documentation that explains thsi process in terms that

Hi! I am new to Asterisk too, I got the similar problem and I would like to know how to get * to work behind NAT. When I have the SIP Debug turn on, I got the error 479 from FWD when * try to register with FWD, it looks like * is using the local IP (192.168.x.x) in the Contact field. I have put the nat=yes in the [FWD.Pulver.com] content, but it does not seems to make Asterisk aware the

I have a Sipura 2000 working fine, but whenever I dial any extension there is a delay of 5-10 seconds before it starts ringing. However, if I dial the extension and hit the pound key after the number, it goes through right away. Is there any way around this?

Hello, We have one of our SIP provider that's is sending incoming sip call without need of registration. Incoming call working fine (as outgoing call), but * still try to register to there sip gateway : chan_sip.c:3159 sip_reg_timeout: Registration for 'phone@50.50.50.50' timed out, trying again -- Got SIP response 404 "User Not Found in data base" back from 50.50.50.50