similar to: No hangup(vpb)

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

Good day all I'm using sip protocol and a openline4 card.If I dial out of the pstn and hangup a answered call it does not disconnect the connection.It shows there is still a call on the external phone I called but on my side its says i'm not connected.We are using x-ten soft phones Can someone please help me Thanks Altus

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

Hi there, I am trying to delay sending out DTMF from Voicetronix OpenLine4 to the CO line. The reason being is that Voicetronix sends out the DTMF too fast even before the line is fully established with the carrier. Usually when dialing an 8 digit number, only 7 digits are actually successfully heard by the carrier. Currently, my dial plan is: exten => _9.,1,Dial(vpb/1-1/${EXTEN:1}) Daniel

hi there, i've been able to successfully run asterisk with the Voicetronix OpenLine4 card, it can accept calls and function normally. The only problem I'm experiencing so far is getting the card to outdial to a third party. What I'm trying to achieve is basically call bridging, where the caller dials in to asterisk, some IVR plays and then attempts to perform a "transfer"

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Hi all, I used to have an OpenLine4 card, but decided against using it due to some problems with hangup detect. Does anyone on the list actively use Voicetronix's OpenSwitch12? What are your opinions on the card? Cheers, Flynn

Has anyone gotten the voicetronix boards to work with Asterisk, what would it take? Or does anyone know where I can get 4 ports or more fxs PCI cards that do work with asterisk? Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-798-9106 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

Hello, list, I am using Asterisk with an OpenLine4 card. It worked well with Asterisk 1.0. Then I upgraded the system, Asterisk 1.4 had some problem to compile chan_vpb, but I managed to compile it manually. Still Asterisk does not work because it refused to load chan_vpb module. I had to revert back to install Asterisk 1.2. Then I get a error: asterisk: hip.cpp:793:

I have installed a 6VPCI card from voicetronix's but i can't get astersik to use it! Now looking at the loaded modules the chan_vpb is not loaded- so I assume that is why it is not working. Now I modified my vpb.conf file and extensions.conf, have I missed something Has anyone a installation guide as I am very new to this!! I have had asterisk working with SIP extensions. by dowloading

Any guidance on how to get my openline4 to get recognized by asterisk@home? I've got my vpb drivers running, but not sure how to add it as a trunk, should it be via zap? or is there another way? Thanks, Chuck

Good day all I'm in South-Africa,currently we are using openline4 cards for our pbx systems.Now we first need approval on the cards form icasa(a government standards) before we can use the card.The market here is very big for a system like asterisk.The only problem is to get a card approved(for a small company like us) its just about impossible. Now what I'm looking for is a company that

Good day all So I've installed asterisk with my openline4 card and I've setup sip and I can do sip on the local network,we are using soft clients,x-lite. But... When a call comes in from the outside(PSTN) and the you dial the extension it forwards the call the the client and you see incoming call on x-lite,you accept he call....BUT there is no sound.It shows there is a call and you are

Hello, Hacker I install VoiceTronix OpenSwitch 12 port PCI Telephone Card, and setting vpb.conf, extensions.conf following My problem is: When i dial to fxo(channel 9-12), it is ok, but when i continue press exten 102, the channel crach with error messages following exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872 Do i ignore some setting for VoiceTronix OpenSwitch12

Good day all I'm getting this error while trying to dial out on my asterisk server using a openline4 card "exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872" Please Help me

Good day all I added the music on hold entry in vpb.conf and commented out default line in musiconhold.conf. Asterisk starts up with the default mp3 but as soon as I remove it and add my mp3 it just doenst start up and gives a broken pipe error? Please Help or advice Thanks ALtus

Good day all I want to put the openline4 card into a box that will support 3 different companies I read the caller ID id fixed but now HOW DO I: If a call come in for 12345 it plays company 1's welcome message If a call come in for 98765 it plays company 2's welcome message ens.. Does This make sense Thanks Altus

Hi, does anyone have any recommended (read tried and tested) way of making asterisk be able to handle incoming faxes. I've a PC running asterisk with a digium E1 card in and simply want to be able to route a call to some application which will take a fax call and save the fax as an image. I guess the bits I'm unsure of are how to terminate a fax call without a modem (if this is

dear Hackers, i have a voicetronix Openswitch card, and i have been finding it very dificult to get it to work with asterisk. i intend to connect 8 ports to the PSTN and 4 as station ports. problem 1: On running asterisk all i get at first i get : event[9=>[11] station OFF hook] on vpb/1-12 even [12=>[11] loop drop on vpb/1-12 event [12=>[11] Tone detect:GRUNT event [2=>[11] Dial