similar to: Graststream ATA 286 Caller ID Europe

I have a E1 conected to asterisk all zap channels are ok, but when calls come into Asterisk caller don't hear none ring, the call goes straight into the menu, how can i simulate 2 or 3 rings? here it is my conf. exten => s,1,Answer exten => s,2,Wait,2 exten => s,3,NoOp(${CALLERID}) exten => s,4,ResponseTimeout,45 exten => s,5,DigitTimeout,3 exten =>

Hello! I'm having a bit of an issue with one of my installations that I cannot figure out. For some reason, when two people are in a call (both local to the * box, same subnet, pure SIP), the call will randomly be placed on hold and provide MOH to the other party. We're using Polycom IP430 handsets almost exclusively for this installation. Can anyone think of a reason why a call would

Hi, Just received recently released Grandstream handytone 286 ATA for testing. I can call ATA from any other extensions and conversations seems to be of quite good quality. However placing calls from ATA is not possible at all to any extensions. After dialing there no indications of any kind from ATA at all. It just "hangs in there". ATA is behind NAT, registers to an * with public IP

I am trying to get the handytone 286 to make a very simple call to * and having problems. It registers with * just fine, but when I place a call (to echo test, for example), the RTP stream seems to have problems opening. Here is there error I get in *: WARNING[98311]: File chan_sip.c, Line 464 (retrans_pkt): Maximum retries exceeded on call 20d1c411-e210-5f3d-3f88-19035c8fcb26@192.168.2.6 for

Hi Everyone, I am running DD-WRT on a router that feeds about 30 Aastra 6753i. The phones occasionally go into "No Service" mode. The POE switch doesn't seem to be the problem as it's tested fine. I think the router sometimes gives up and comes back quickly. Or something of that nature. However, the connections are maintained if a call is going on because there are peer to peer

Someone have info about install an AVM fritz into FC3 ? I'm getting problems with kernelcapi, after succesfully installed the fcpci support. Thanks -- Adri? Vidal adriavidal@gmail.com Mail is better with 1Gmail

I'm considering a situation where I buy about twenty ATA devices. I've played with the Linksys / Cisco PAP2T, and got that working fine with some inbound and outbound faxing. The web GUI was okay. I'm seeing prices around $45 to $50 for this thing. It comes with two FXS ports, but I only need one FXS. I've seen the Grandstream Handytone 286 online. It looks promising as an

I have an analog Fax machine which I wish to connect to the network and the Asterisk server. It will connect through a GS Handytone 286 converter and then into the LAN. Is there any information out there on what I need to write in *sip.conf* and/or *extensions.conf* to make sure the fax works as a fax? Channel 8 on my T1 is a reserved, dedicated line for the fax number. Do I need to

There seems to be a problem related to the Grandstream HandyTone-286. When a call is placed through the adapter, the call can be transferred. However, when a call is received through the adapter, the call cannot be transferred. The problem does not exist with a BudgeTone-101 (1.0.4.23) using the same Asterisk configuration and Dial() settings (Ttm). I tried all of the firmware on their BETA

Someone can confirm the new release is out? Haven's seen any post about it!!!!! -- Adri? Vidal adriavidal@gmail.com

I am trying to setup a simple pstn gateway using Asterisk and a X100p card. I have got everything installed using Redhat 9 and am able to load Asterisk. I also configured sip and I am able to connect to the asterisk gateway with Xlite on the windows side. I am able to dial 1000 and get the welcome message. What I am NOT able to do is dial a seven digit local or 10 digit long distance number and

Hello, I bought a Grandstream Handytone 486 to forward incoming calls from our old analogue PBX to the asterisk server. My first test was connecting an analogue phone to the Handytone and calling a sip phone - worked. Now I used the same cable to connect the line port of the Handytone to the analogue pbx. When I call the number of the analogue PBX I hear a clicking inside, but the call

Hi, I am quite new to asterisk so I am not sure what is needed to figure out this problem. If more information is needed and not provided I will gladly provide it. I have a very basic asterisk setup. 1 x100p card and a grandstream handytone 286. I can make calls fine to most phone numbers from the handytone device the trouble seems to come when I dial this number 591-1079. It puts me through to

I have problem with fax machine Panasonic DX600. It's connected to Grandstream Handy Tone 386 which is connected to Asterisk. Asterisk is connected to my SIP provider. To some numbers I can't send FAX, and I get following error on CLI. WARNING[2237] chan_sip.c: Unknown SDP media type in offer: image 31358 udptl t38 I believe that Panasonic DX600 machine supports T38. And when I have

Hi ; Have two handytone 486 and want to use them as digium TDM400 fxo-fxs card... I mean is it possible to direct pstn calls from astersik (extensions) to handytone line port directly and vice versa ?... Thanks in advance Betul Onemli not : Bu e-mail iletisi, sadece adreste belirtilen kisi veya kurulusun kullanimini hedeflemekte olup, mesajda yer alan bilgiler kisiye ozel ve gizli

Hi Has anyone opened up a grandstream phone or handytone ATA to find out what is inside? What is the CPU? How much RAM? Cheers Rob

I'm getting "Got SIP response 406 "Not Acceptable" back from 10.0.1.2" occasionally when try to dial to SPA942 , anyone has any idea on this before i consider Firmware upgrade? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080326/2fd2c557/attachment.htm

Hi list, I have for a year I have an account to call with broadvoice from about 3 days beginning a not registered problem of, asterisk shows to a message of error with the DNS, and my dns this working fine WARNING[5770]: chan_sip.c:7595 transmit_register: Probably a DNS error for registration to 908XXXXXXX at sip.broadvoice.com@sip.broadvoice.com, trying REGISTER again (after 20 seconds) [Dec 16

We are looking to deploy asterisk at one of our locations that will have about 50 phones. I have been buying different phones to test there quality and feature set. So far we have a Grandstream 2000 Grandstream HandyTone 488 Cisco 7912 Polycom SoundPoint IP And we are looking at getting a Linksys SPA-942 Anyone have a favorite? -------------- next part --------------

Hi I have a analog phone connected to my Gateway Handytone and registered to Asterisk 1.4 I have configured my HandyTone 488 (in the section FXS Port) for make and receive calls, however I can not transfer a call when it come via PSTN. But, when a call come from via IP I can transfer it. [phoneanalog] type=friend secret=XXXXXXX context=local nat=no qualify=yes host=dynamic dtmfmode=rfc2833