similar to: ATA & T.38 Fax

Hello Guys I have 2 azacall 200 as extensions for a Internet public asterisk box , I just want to connect point A with point B I have tried canreinvite= yes / no Nat=yes/no Nat=1/0 commented canreinvite commented Nat, I have no audio with other azacall or to other sip device in the same asterisk. Note: other devices like grandstream , siipura, Virbiage, and xtenworks perfectly ,, just

-----BEGIN PGP SIGNED MESSAGE----- Greetings, I've just about got Asterisk up and running and am wondering the following. Currently, I subscribe to both Vonage and Broadvoice and as such, I've got a Sipura and Cisco ATA186. Although I'm sure this is expressly prohibited somewhere in my service agreements, can I reprogram these devices to access my own asterisk server rather than

Hello, I am very new to asterisk and voip in general and so far have managed to get the FXO card and a few sip phones working fine. My question is where does the Sipura SPA 2000 come in the picture? Can it be used as an extension (i.e FXS) ? Or is it to be used as a line (i.e FXO)? Or it can be used as both? My understanding is that its just like another ATA186. Is that true? I guess what I

I am looking for an ATA that has had very reliable results when passing FAX over IP. I was thinking of testing the Cisco (not Linksys) ATA 186 I1, ATA 186 I2, ATA 188 I1. This is what I'm looking for: FAX -> PTSN -> through Asterisk -> ATA -> Fax Machine. I have QoS from PSTN entry to ATA on the network so I can assure precedence. What has everyone out there been using

I've just made an interesting observation that I'd like to share with you all: the popular Sipura SPA-2100 just doesn't seem to be as great as I'd hoped. I've been trying to get inbound AND outbound faxing working via Asterisk and at least one of my termination services: Voicepulse or Sixtel. In general, inbound has been working flawlessly but outbound has been pretty

I have an ATA186, a tech just told me to set UID0 and UID1 to the same username, and PASS0 and PASS1 to the same password. In my mind, this would seem to have the unit registering twice under the same account, which Asterisk wouldn't support. When a call comes in, it should go to the last line to register. So to me, this means the call could sometimes come in on Line 1 and sometimes on Line

Ok, ok, I know there has been plenty of discussion on asterisk and fax - from this I understand: 1) First and foremost, use g.711 ulaw 2) Packet loss, etc...makes faxing over the internet unreliable My need is for a fax to come in on a X100P and be forwarded to a fax machine on the local lan. I don't currently have any fxs as I'm using all sip phones at this point. I see the

Need to replace our older soho fax machine with something more current. Would like to run the fax line through *, but haven't been able to make spandsp work correctly with digium TDM04b card. Our fax volume is very low (maybe a few per week), but we have multiple offices in three geographic locations and would like to be able to email the images to the correct location. For planning purposes,

I've configured Asterisk 0.7.2 to work together with Cisco ATA186 (SIP,G.711. RFC2833) and OpenPhone (H.323, G.711). But there is an issue while calling from ATA186 to OpenPhone via Astrisk - when I press any key on analogue phone connected to ATA, Asterisk shows following message: -- Executing Dial("SIP/519-3781", "OH323/62.213.36.100|20|Tt") in new stack --

Hello all ! Can anyone recommend me ATA device that REALLY has T.38 built in. So far I have heard of Telco Systems Access201, which seems to be impossible to bye in Europe (all resselers are droped Telco systems ATAs for some reason (tried in Germany and in UK so far)), and I have heard that SIPURA SPA-2100 should have T.38 built in into newer firmware, but I wasn't able to confirm that

I'm having a horrible experience getting a Cisco ATA-186 to work with *. I can make calls from the ATA with no problems. However, incoming calls make the ATA ring once, and then the call is disconnected. I have no problems with my Sipura 2000 or my Grandstream phones. I am running 2.16.1 sip code on the ATA 186. Neither * nor the ATA is behind a NAT. They are both on public IP addresses

I've installed Asterisk and configured an ATA-186 as described at this link: http://www.djernes.org/~shawn/ata186.htm Unfortunately this guide abruptly ends before it explains how to deal with the sip.conf and extensions.conf files. So I left extensions.conf alone and my sip.conf looks like this: [general] port = 5060 ; Port to bind to bindaddr = 0.0.0.0

I've done something similar at home, but made my dialplan such that I can dial either 10 or 11 digits locally. I don't use a "throw away" digit at all. Any 7, 10, or 11 digit call will be appropriately mangled and sent out the PSTN / VoIP provider. ________________________________ From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On

how to adjust voice volume for sipura 2000 and cisco ata186?

Hello! Anyone with some insight into the oh323 channel driver please shed some light on the code block below from wrapendpoint.cxx. When enabling trace on the channel driver i get this, for me, strange debug info: WrapH323EndPoint::OpenAudioChannel: Direction => PLAYER, Buffer => 320 WrapH323EndPoint::OpenAudioChannel: FrameSize 8, FrameTime 8, TimeUnits 8

I have an Asterisk server that I use at work. I have a phone that is at home that logs into the Asterisk server at work. My home phone is hooked up via DSL through a Linksys router. You can see the my sip.conf for the phone blow. The problem is each time the phone rings I can hear/be heard 50% of the time. Any suggestion on what to look for. I do have my reg time set for 180 seconds on the

Hello, I'm planning to convert my phone system to Asterisk, as I've outgrown my TalkSwitch system. I have a few questions for experienced * users, most of which can be answered yes/no. Current Setup: - Talkswitch 48NLS (4CO/8Ext) phone system. - One CO line, two Vonage lines, one Voicepulse line connected to phone system - A third Vonage line directly connected to a fax machine - A

I know the subject of faxing has been covered in some detail, but I was wondering if anyone has a hardware configuration similar to ours that has faxes working successfully and would be willing to share any settings/insight. We are unable to fax reliably with a Sipura 2100 connected to Asterisk. We do not route calls over the Internet and our network has very low latency. The Asterisk

was breezing over http://voxilla.com/ Looks like a new ATA from the founder of Komodo Technology (aka the Cisco 186) Sipura SPA 2000 http://www.sipura.com/products/spa2000.htm to join the others Cisco ATA 186/188 http://www.cisco.com/warp/public/cc/pd/as/180/186/ 8x8 DTA-310 http://www.8x8.com/products/home_office/dta-310/index.asp.html Grandstream HandyTone 286

Folks! We have purchased G729 and have been testing the codec on mUltiple Gateways. Here is what we have found. Here is the config I have used: ------------------------------- Asterisk Server On Dual Pentium Xeons with 6GB of RAM, running on Fedora Core 2 User1 is in USA on Broadband Cable User2 is in India on 64Kbps ISDN Line User1 using SIPURA SPA 2000 user2 using Xten professsional(X-pro)