similar to: spa 3000 help

This post is simply documenting a spouse-friendly way of using the spa-3000 as both a fxs and fxo port for basic soho environments in the US, allowing asterisk to participate as needed/wanted. All home phones are connected _only_ to the spa-3000 fxs port. The incoming home pstn line is connected _only_ to the spa-3000 fxo port. Defined Line 1 (fxs) to register with asterisk via sip (extn

In my seemingly endless search for the cause of echo on my SPA3000, I wired it up in the following configuration: Analogue Handset <--> (FXS)SPA3000(FXO) <--> PAP2 And set the Line1 dialplan on the SPA3k to '(<:@gw0>S0)' which means that as soon as I pick up the handset I get linked straight through to the PAP2, which gives me dialtone. Even in this configuration, with

I am still haveing problems (echo) with my X100P but I'm thinking it has more to do with the server it is in which is not a negotiable item at this time. My question then is to the use of SPA3000's as a replacement from the FXO standpoint. 1. Can you setup the FXO port to recognize distinctinve ring and call a different context like you can do with Zap channels? Being able to call a

Since the 3000 has been out for a little while, has anyone done a review of the product? (couldn't find anything on google for wiki). Can the fxo and fxs ports be used as two independent channels? Is it really read for prime time? Etc. Rich

Hello, Just want to tap the collective wisdom of this list as to experiences pertaining to the Handytone HT488 and the Sipura SPA-3000 adapters... Basically I'm looking for a FXO/FXS/LAN ATA and these two seems to be the top of the pick..Any comments and experiences esp. with Asterisk compatibility would be great, before I plonk in the bucks. TIA. /wai-sun

I've had an spa3k in service here at the house for a while now. After some initial wrangling, it's been working okay. I've had to reboot it a couple times and have noticed something rather annoying though. My setup is pretty simple and, dare I say, common. I have the SPA-3000 "inline" between my incoming POTS line and the internal house phone. It's setup to deliver

Hello, Before throwing in the towel with my Sipura 3000 has anyone had much success with that adapter connected to a door phone? In our setup a doorphone is connected to the SPA's fxs port. When a visitor rings, asterisk calls a group of Polycoms and the person who answers has to enter *1 to trigger the door opening. However it seems the SPA doesn't relay the DTMF's to the

Voxilla.com has a great config wizard for the SPA-3000 and * http://voxilla.com/spa3kasterisk.php I took the output from this wizard and dumped it on my test box with an SPA 3000 (with some mods to match my * contexts) and everything worked great. Calls from the PSTN to the spa3000 are routed to dialplan #8 on the spa3000, which dials * Both the FXO and FXS port register with * The SPA3000 is

This is a wierd one. Can't figure it out. I have an SPA-3000 at the house handling my incoming line. It's setup to direct the incoming call to asterisk. Works great 99% of the time. A few times a day, I'm getting calls that ring once internally and are then hungup. I managed to get a detailed log [1] of what's happening today and it looks to me that the SPA is acting wierd.

I am considering using Sipura-3000s as FXO devices for my * system. Has anyone tried them in that configuration? They interest me because they need no PCI slots and therefore no drivers. I would much prefer not to have any special kernel requirements for my system. /carmi

I'm sure there must be a setting I'm missing somewhere, so I thought I might was well ask here. Conversations are punctuated by sudden replacement of a given syllable or so of conversation with a DTMF tone. I would hope perhaps there's some kind of setting that has to do with the way it detects inband DTMF? I'm pretty sure it's an artifact of this particular ATA; my

Hello all, I have an ISDN termination box (TR1) that converts ISDN(Bri) to 2 normal analogue lines. The same number is assigned to these lines. These lines are connected to 2 spa3k registered to my asterisk box. When calls arrive, TR1 try to pass call to the first spa. If spa not takes the call immediately then try to pass to the other spa. The only configuration I found works is to put the

Thanks Rich, I have an SPA-3000 laying around, so I will attempt to set it up in a little more conventional manner (although your method looks like a winner for a home test PBX). Would you mind posting or PM your current config to me, maybe screenshots if you PM. If I start with that it will take less time to get to the point where the SPA-3000 is a true FXO-FXS gateway for *. I will be happy to

My apologies for the off-topic post ... No matter what settings I try, when I dial in to the SPA-3000 on the PSTN line, it picks up the call and immediately gives me a fast busy tone then hangs up. The info tab says under PSTN Line status: Last PSTN Disconnect Reason: PSTN Disconnect Tone which seems to indicate that the SPA thinks the caller has hung up. Since I am in Japan, it is possible

We have issues with all of the SPA-2000 ATAs we have where incoming calls from only one of our Asterisk servers do not complete. Details: 1- On the CLI we see that when the call is pushed to the ATA it shows Busy/Congested 2- We can make calls to this same server just fine 3- We can receive calls from other Asterisk servers running older CVS versions of Asterisk with the same exact ATA

If I have multiple Sipura 3000 device how can I dial out properly? I can receive call without any problem and that's working really well. Caller ID is shown and when someone call he get's the welcome message the same way I have it configure with the X100P card. I don't seem to have any echo problem with the Sipura 3000 (but I do with X100P cards) My main concern is for

Hallo! I had ordered a Sipura SPA-3000 in the UK, but the supplier turned out to be unreliable and never shipped. Yesterday I went looking for alternative suppliers and found the Linksys SPA3000 device. It's a different box, but the specs look very similar. Is this the same device? Has anyone used this Linksys SPA3000 successfully with Asterisk? Thanks, Frank

More an echo algorithm question than a purely asterisk one... I have the following setup: Handset - PAP2 - Asterisk - SPA3000 - Telco And no matter what I do, I get echo on a call routed out via the PSTN when I talk into the handset, in the order of a hundred ms (my estimate, could be wildly inaccurate!). Echo will occur also when I have a handset plugged into the phone port on the SPA3000

I've a problem. I've some spa3000 and spa2100. Asterisk 1.2.4. Prefered codec g711u in both. Calleng from a fxs of spa2100 to the fxo of spa3000, all works ok. Then I call from a sip phone configured for using g729, to the fxo of spa3000, it also works ok. The problem is that after this, when, making again a new call from spa2100 to spa3000, spa2100 receives only white noise. I suspect a

Hi all, I was wondering whether anybody here would help me clarify this minor issue please. If I have the following setup; Asterisk ------ Sipura SPA 3000 (fxo) --------- Pstn Line Would a call coming in on the pstn line be answered by the ATA or just get passed through to the * server (depending on dialplan) to handle? So basically, the caller does