similar to: How to force G.729 in H.323 calls

Hello, All! We was upgrade our Asterisk from version 0.7.2 to 1.0.7. And have big problem. When asterisk starts: ------------------------------------------------------- *CLI> h.323 show codecs Allowed Codecs: Table: G.729A{sw} <1> G.729{sw} <2> G.723.1{sw} <3> G.711-uLaw-64k{sw} <4> Set: 0: 0: G.729A{sw} <1> G.729{sw}

Hi all, I'm having trouble with H.323 outbound calls, * connects but there is no sound in both ways. I'm using X-Lite as SIP client with GSM codec and dialing to ITSP (which using cisco, I think) over H.323 with G.729 codec. I have 4 digium G.729 licenses installed and this is onli one call. I tested my * with another ITSP over SIP and G.729 codec and there was all ok Here is my configs

Hello... I'm having problems with H323/G729 setup. Below is the output of h.323 debug when making a call. I use a SIP phone connected to an * box in the same LAN. The * connects to a h323/g729 PSTN terminator through internet. Calls rings and are answered in the other side, but I get no sound at all nor the other side does (complete silence in both sides). I thought this would just happen

Hello... I'm having problems with H323/G729 setup. Below is the output of h.323 debug when making a call. I use a SIP phone connected to an * box in the same LAN. The * connects to a h323/g729 PSTN terminator through internet. Calls rings and are answered in the other side, but I get no sound at all nor the other side does (complete silence in both sides). I thought this would just happen

Hello all, It's me again. I would like play with calls between a H.323 client and a SIP client through * inside my LAN. For that, on host 192.168.1.20, I use GnomeMeeting (GM20) and Asterisk; on host 192.168.1.25, I use SJphone (SJ25) as SIP client on Windows and I register into * with a username, no password. The 3 files oh323.conf, sip.conf, extensions.conf are in attachment. In the same

Hello, I've been trying to send traffic to a Cisco Call Manager 3.2, but with no luck. Here's whats happening: * Call gets to CCM * Call gets to the gateway * Rings a couple times on destiny * Call gets hungup. On the CCM I get the following error: MediaManager - ERROR wait_AuConnectErrorInd On the Gw (Cisco AS5300) I get a disconnect cause of 2F (Resource not available) On asterisk:

hi .. i've just installed and licensed an instance of the G729 codec. I am trying to connect through asterisk to Go2Call server .. According to their info it involves dialling extension 729 on voip01.go2call.com, to get the IVR. my extensions.conf shows : exten => s,2,Dial(OH323/h323:729@216.52.153.206) which I think is correct, I have G729 enabled in the OH323.conf file and it seems to

Could you help me with this problem? When I call H323 gateway there is no sound in both ways. Here is h323 debug: ----- begin ------------------------ -- Executing Dial("SIP/msn-6297", "H323/73952389512@peer:1720") in new stack Allowed Codecs: Table: G.729A{sw} <1> G.729{sw} <2> G.711-uLaw-64k <3> G.711-ALaw-64k <4>

Hello, I have a strange h323 issue. After executing command "Dial("SIP/333-0d1dfe00", "H323/361737052390920 at ccg|5|tT")" at Oct 18 22:32:23. Meanwile I have sniffing traffic on port 1720. The call was established just at Oct 18 22:33:03 (New H.323 Connection created.) and also packet sniffer grabs the h323 invites at this time also. So my question is what

Greetings to the list: this is my problen when I make a call from my asterisk towards a nortel PBX , the call is made but in my telephone sip I do not listen the dial tone or the busy tone but the call it is completed normally. sip-phone-g729-------------asterisk--------h323-g729--------------nortel-pbx thi is may configuration: RedHat 8 2.4.18-14 Asterisk 1.0.7 The NuFone

Hi all, I am trying to use a "Siemens optiPoint 300" IPPhone (H.323 only) with Asterisk (1.0-RC2). So far I have been using the H.323 channel included in the tarball (Nufone ?). I encountered a strange behaviour when I try to make a call from the IPPhone to my Asterisk box : =====> here is the H.323 configuration for the incoming calls (192.168.1.50 is the IP of the

Trying to configure voicemail with H.323 all I get is the following errors when I call 123, 666, 665, 664 or 031. I'm a newbie at this so, I think it might be a simple fix. [chan_oh323.so] => (OpenH323 Channel Driver) == Parsing '/etc/asterisk/oh323.conf': Found 0:00.004 OpenH323 Wrapper OpenH323 Wrapper Version 0.0alpha0 by inAccess Networks

Dear friends, I have compiled and installed h.323 in my asterisk. And I have a service from a H.323 VoIP provider who give me user, password and gatekeeper IP address. All configured. But when I start my asterisk i receive the following error and h.323 calls can not be making and/or receiving. [chan_h323.so]=> (The NuFone Network's Open H.323 Channel Driver) == Parsing

Hi, I've oh323 chan installed and working to make calls from SIP to H323 devices. The problem is can no hear sound with the H323 device. I think this is some related with codecs o nat, because the H323 have one public IP from a different subnet from the asterisk box. If I use netmeeting in gateway mode, the call can be completed and I can talk with a SIP device, but in gateway mode I can not

Hi all, I have two problems with h.323 in * The first one is, I can call my voip-phone, (exten => 59305004,1,Dial(H323/${EXTEN}@192.168.0.41)) BUT, I hear nothing in h.323 debug mode: *CLI> Allowed Codecs: Table: GSM-06.10{sw} <1> Set: 0: 0: GSM-06.10{sw} <1> -- Making call to 59305004@192.168.0.41. == New H.323 Connection created.

For the benefit of everyone, having H323 Configuration problem due to H245 Tunnel, check the h323 Config embeded at the end. Comment the offending line as under: ; ; Enable H.245 tunnelling (yes,no). ; h245Tunnelling=yes ; -----Original Message----- From: Tola Ogunsan [mailto:tolaniye@hotmail.com] Sent: Wednesday, May 25, 2005 1:03 PM To: Kanuri, Seshu (Company IT) Subject: RE: oh323 problems

Hi, I am trying to make a call from SIP to H.323 using chan_h323. Asterisk CVS-HEAD-03/10/05-10:08:22. As given in chan_h323 readme I compiled pwlib and open h323 versions 1.8.1 and 1.15.1. Call seems to be get connected but no audio path. I see following; -- AGI Script Executing Application: (DIAL) Options: (H323/YYYY#XX112422428@XX.103.19.91/XX112422428|60|HS(63840)) -- Setting call

I've done some reviewing of the archives for G729 and H323 experiences. The landscape of that query isn't pretty - lots of pleas for help, and nor do I see too many "answers." I have a pending bid that requires some data before I can implement * on this particular solution. My question is perhaps a slightly differently worded one than has been asked before, but it may be

Hi, I need an Asterisk with G729 support. Preference is with Asterisk 1.2(.18), but if not possible, then it can be 1.4. Question is, can I enable G729 for both protocols? do the H323 implementation allow it? I found the codec support for H323 in 1.2.18 very poor ... only got u/a-law to work ... not even GSM. Would the Digium G729 license be good both for SIP and H323? Cesc