similar to: Somebody using AS5350 CISCO?

Try sending 5350 config and oh323.conf, versions, etc... -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Goran Dj. Sent: Wednesday, December 22, 2004 4:43 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: [Asterisk-Users] Asterisk->AS5350 misplaced RTP to 127.0.0.1(AS5350 party

My configuration is: [ISDNPRI] -- [CISCO AccessServer AS5350] --<H.323>-- [ASTERISK] -- [CISCO ip phone 12SP+/Skinny] When call is initiated from IP phone -> Asterisk -> AS5350 -> ISDN everything working ok (RTP is ok). But, when call coming from ISDN -> AS5350 -> Asterisk -> IP phone IP phone party can hear ISDN party, but ISDN (incoming) party canNOT hear IP phone party

Hi, I am currently interconnecting to a PRI using a Cisco AS5350. I'd like to be able to dial specific numbers out by a specific isdn channel, so for e.g. if I dial 999 01 12341234 it should send 12341234 out via isdn channel one from the Cisco AS5350. If somebody would be able to guide on this, it would be appreciated. Regards, Sahil Gupta VoiceValley

I'm using sipgate.de as my sip provider. When I'm using xlite as client on sipgate.de, everything works fine: I call number, hear ringing (real progress tone form called party, not one generated in xlite) and then talking with called person. But, when I'm using Asterisk as sip client on sipgate.de, I don't hear progress tones: I hear only one (locally generated) ring tone, and

Hi all. I have a strange problem, I've got a AS5350 hooked up to a telco using two trunked E1's The 5350 should only act as a GW to a sipproxyserver. THe thing is it seems to be only oneway audio? There are no firewall at all, and the audio still only get one-way When I call from pstn --> as5350 --> sip-sip-phone I can here the sip-phone ,, but the sipphone cannot her the

If my extension is 22, and voice mail access number is 909, then with exten => 909,1,voicemailmain(s22) I can access voice mail 22, without number and password prompt. But, I want that every extension can access its voice mail without number and password. So, when I put exent => 909,1,voicemailmain(${calleridnum}) voicemail want only password. I want to eliminate password too, so when I

Somebody must have! Please, send me a g723 and/or g729 (for Asterisk) to pisac@hotmail.com (antispam subject: codec) Thanks, thanks, thanks... :-)

Hi, Just wondering if anybody has encountered a similar problem as I have with recieving calls on Asterisk from a CISCO AS5350 (over SIP). I have dtmf relay configured on the AS, however, when someone calls in from the PSTN sometimes their digits are inputted twice, which messes up the extensions. If there is a better way to terminate calls from a AS without using SIP, that would fix this

Hello, I've got an ISDN PRI circuit terminating in a Cisco AS5350, which in turn is talking to an Asterisk server via SIP for call origination and termination. Seems simple enough, and it works for the most part, but: 1) Caller ID name data comes in on the PRI, but doesn't appear to get handed off to the Asterisk server via SIP, at least not in any format that Asterisk

Here is my Configuration PSTN -> Cisco AS5350 -> SIP -> ASTERISK -> SIP -> ATA186 When I call from the pstn to the ATA, the ATA rings but I don't hear anything on the calling side until the call is picked up. When I call from the ATA, everything seems to work fine. When I bypassed ASTERISK, everything seems to work fine. Anyone know what I might have configured wrong?

Why Asterisk showing (on SCCP and H323 phones) different CID related to type of Incoming channel: If incoming channel is SIP, on phone is displayed CALLERIDNUM If incoming channel is ZAP, on phone is displayes CALLERIDNAME It vas very frustrating! I lost couple hours of my time to find that my dialplan is not faulty, but asterisk is!

I really hope that someone can help me with this one. DTMF tones are not working for certain places that I call, specifically 1-800-882-8880 which is the AA advantage line. It works for almost everyplace else. If I bypass asterisk, the call works fine. Network looks like: <SPA-2000> --SIP-- ASTERISK --SIP-- <AS5350> --PRI-- PSTN sip.conf entries [VGW01] (this is the AS5350)

Hello that might would be an easy question for someone, but im in doubt Is there any possibility to pass a call from one asterisk to another and then to ZAP channel. For instance I have "A" asterisk with numbering 45670 "B" asterisk with numbering 45680 second asterisk has TE110P card with single PRI port connected to Siemens EWSD. When I originate call from asterisk

I have an * box connected to a Nortel SL100 through a PRI (US) using the Digium TE410P (quad-span T1 card). I don't have access to the SL100 - it is handled by another group. The span comes up OK (timing, framing fine). However, as soon as the D channel comes up, I get endless "HDLC Bad FCS" errors. I modified logger.conf to get rid of the messages (so I could see what else was

Juan, I am running a Calling Card application on a Dell PowerEdge 2850 with Asterisk 1.0.7. Recording conversations I have seen on my server causes the processors to burn more than necessary so I would recommend what William from Signate recommended: " Consider saving recorded calls in a database on a separate server. It will be simpler to build a retrieval interface that does not

I am now at a total loss. Using Sipura spa-2000s connected to *, I get DTMF working just fine for internal extensions, voicemail, etc. If making an outgoing call like this spa --> * --> Cisco AS5350 --> PSTN, I get no dial tone. I am working unsuccessfully with Cisco right now on this, but they cant find anything wrong. I have tried all suggestions I can find from the list and elsewhere.

Hi, I'm using an Asterisk Server and a Cisco AS5350. They are interconnected via Sip. When I tried using G.729 codec, all recorded announcement of asterisk is no longer heard in the system but when I bring it back to G.711 the announcement works perfectly. Any idea how I can make the announcement work in G.729? Thanks. Cheers, nat -------------- next part -------------- An

Hi all. I'm going to implement some large Asterisk based solution. Maybe 4-5 PCs with 1-2 E1/T1 trunks on each. Because some of the traffic will be sended to external VoIP provider, i has some questions 1. Which is the lowest bandwidth consuming codec in Asterisk, which is compatible with Cisco Gateways. Stability is needed too. 2. Have someone allready bulded such a systems and what

Has anyone succesfully integrated * with a cisco voice gateway ? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20031214/3b1ba7b3/attachment.htm

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hey all, I'm having problems with calls dropping after 15 - 20 seconds from a particular provider. The are using a NexTone gateway. Here are the details: Successful call: INVITE cseq 1 From NexTone 100 Trying cseq 1 From Asterisk 100 Trying cseq 1 From Asterisk 200 OK (G711U) cseq 1 From Asterisk ACK cseq 1 From NexTone INVITE (G711U)