similar to: Fw: OT: Opensource "Sipura Profile Compiler" for SPA2K, 3K

Hello list, I have several SPA-2000's and 3000's scattered about the Internet (all behind NATs). Because I do not qualify as an ITSP, Sipura will not license their "Sipura Profile Compiler" so that I can have the units remote upgrade, remote re-configure, etc (via TFTP or HTTP). This is extremely annoying. Right now if I have to make a config change to any of these

Anyone have experience with Sipura's? Anyone know if they offer a warranty? Would like opinions on these, good or flame. We bought *one* to test with and it died, can't even get a response from Sipura "support". Could anyone recommend another device to replace these? Prefer 1 or 2 port design. Ty :-)

This question isn't entirely Asterisk related, but I'm hoping that someone here may have the knowledge to respond to me anyway. I'm using Asterisk with several Sipura SPA-2000 SIP devices as FXS adapters. I would like to have my SPA's automatically provisioned through http or tftp, but I can't find any information on how to do so. Sipura's tech-support has not been very

Does anyone have a Sipura 3k running, and using the FXO? I've got things working right, but if I try to toss a *67 in the dialplan, it seems the sipura is throwing a 403 forbidden back. For example: exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/${EXTEN:1} works fine exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/*67${EXTEN:1} does not (even if I toss a couple Ws in) I can't

I just got a refurb Sipura SPA-2000 and was able to assign it an IP address with DHCP and ping the device, but then I ran the firmware upgrade utility to bring it up to spa2k-2.0.13g which seemed to work just fine, but after it rebooted I cannot connect to its webserver for configuration. I can still ping the unit. When I use the built in voice menu it reads back the right IP address, webserver

I have a sipura 3000 that I am using just to send calls to my mac asterisk server. When you call the phone it rings, answers, and then goes right to a busy signal. Any ideas? Thanks for your help! Jane At the console in verbose mode I get: *CLI> DEBUG[8501248]: File chan_sip.c, Line 663 (create_addr): Setting NAT on RTP to 0 DEBUG[8501248]: File chan_sip.c, Line 554 (__sip_ack): Stopping

So far I have gathered that on my NAT (where asterisk server is) I have to port forward UDP ports: 5060 and range 10000 - 20000 to my asterisk server But I'm still stuck how to configure Sipura (behind NAT) what sip proxy and out-bound sip proxy, under which tab to change. -- #Joseph

All, If you currently own a Sipura SPA2000, avoid going to the sipura website and upgrading the firmware. I upgraded my SPA2k a couple of days ago from 1.0.9 (what it came with) to 1.0.18 off the site, and I am having issues with my SPA rebooting itself every 3-10 minutes for no apparent reason. I have been in touch with the *excellent* sipura support folks, and they are working with me to

We have an application which is primarily DTMF driven (automated on both sides), which we are trying to deploy over VOIP and Asterisk (using some Sipuras and some IAXY's). We are finding that in around half the cases, the Asterisk server can't decode the DTMF digits from the field office (or at least some of them). Though, when we place voice calls for testing, we can hear eachother quite

Is anyone else having problems with Sipuras not being able to re-register to Asterisk after applying the cvs update last night? Just curious if I need to roll back or take all of my Sipuras out back and beat them.

Hi there everyone! I've bought a Sipura SPA 3000, and succesfully connected it to my Mac, where I installed Asterisk 1.4.0. Both ports (FXO and FXS) are well configured). However, living in Brazil, I'd like to know if there are optimal settings to my PSTN that I should enter into the config of the device. I experience a little bit of echo on the FXO probably because I raised the gain of

Hi list, Well I really didn't want to see things get to this point, but Sherman at Sipura along with their President Jan F. leave me no other choice. SIPURA has been provided a letter from our attorney for Breach of Contract and damages. They have yet to respond. A quick background. 1. Sherman (SIPURA's Director of Marketing), stated that we would do a join press release for the Oct

Hello everyone, Even though a lot of it was a bit last minute, several of us from the commnunity made it to Baltimore to help Digium with their booth at ISPCon. It was a great time. Gregory Boehnlein, Brian Capouch, Christian Savinovich, Kristian Kielhofner (me), and John Todd (not pictured) were there (as well as others), and some pictures were taken (the up close ones of me were very

I am trying to configure the FXO port on a Sipura-3000 for use with Asterisk. When I connect to the Sipura to dial out on the PSTN line connected to the Sipura's FXO port, it gives me the dialtone of the PSTN line and then I can hear the DTMF for the number I dialled beforehand. It does work but the customer perceives this delayed second DTMF feedback as "unprofessional" and the

<< Has anyone seen something like that and is there a fix? A google search didn't turn up any apparent hits.>> I have seen exactly this problem. Even IVR failed to work. Got an RMA from the supplier and they exchanged with no questions. Bill Seddon -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On

who can tell me how to do TDM over enthernet ? pc a connect pc b only use TDM card? thank you John. -----????----- ???: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com]?? asterisk-users-request@lists.digium.com ????: 2004?12?23? 11:47 ???: asterisk-users@lists.digium.com ??: Asterisk-Users Digest, Vol 5, Issue 336 Send Asterisk-Users mailing list

Hi everyone, I'm having an odd problem with one of my sipura boxes. The box registers the first time with asterisk properly after being plugged in. After which, some of the subsequent registration tries fail and the box becomes unregistered. However, after a few hours, it finally successfully re-registers and the cycle continues. I have not been able to figure out the problem but

Folks! I discovered some serious problem with several Sipuras 3000 but I don't know if the problem is with them or Asterisk. Basically, if I call a Sipura PSTN line, when there is a call already in progress, generally I get a 503 Sevice Unavailable, but if I try hard enough, I am able to get through and connect to dialed number. The other call gets disconnected but the originator of the

We are using MFC/R2 driver successfully in at least three places in Brazil. I have problem with an Asterisk integrated with MFC/R2 with a Siemens Hicom 300. I can get a good audio quality with Grandstream, Polycom, and X-Lite softfones, but SIPURAS and Linksys get a garbled audio, something like a "Darth Vader" voice. We have tried everything in Sipura. The SIPURA 2000 and the Linksys

This was so interesting I had to move it to its own thread! Is anyone using this script? How does it perform compared to the older WonderShaper script? -M- ================== Thanks Kristian I will checkout the new script and see how it goes! Jonn -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at