similar to: Big zaphfc issues

I've got some weird behavior on my HFC-s cards. asterisk CVS-06/26/04-21:28:35, bristuff 0.02, libpri 20040510, zaptel 20040623 When i pick up my ISDN phone on Zap5-1 ("3987") and call the external number "1901" it will do so, connect me and everything is fine. In the second, where it tries to attempt the native bridge, the audio will disappear. Using another card

Hi all, I really hope that you guys can help, because I've been tearing my hair out for the past 5 hours on this one. I have a Zaphfc (BRI) card in TE mode connected to the S-Bus of a Nortel Meridian phone system. Phone calls from the Nortel to say MSN 510 are correctly being sent to the right SIP phone. When asterisk dials say Zap/g2/224 (a Nortel internal extension) the call goes

Hello all, if I try to call from one phone on the internal S0 to another on the same S0 using zaphfc, the bus is hung up. The called phone is ringing, but I can't talk from one phone to the other. The error I get is: -- Executing Dial("Zap/2-1", "ZAP/1/55|15|tr") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 1/55 -- Channel 0/1,

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

I've this error How i can find the problem? Apr 23 12:24:43 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:47 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:48 WARNING[131081]: PRI: !! Got a UA, but i'm in state 1 Apr 23 12:24:53 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:25:02 WARNING[131081]: PRI:

I've a lot af this waring May 12 18:44:35 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: received TEI check request for TEI = 76 May 12 18:44:36 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 May 12 18:44:42 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: received TEI check request for TEI = 76 How i can resolve it? Thak's Tiziano

bri-stuff.0.1.0-RC4a on debian sid with 2.6.7 kernel isdn sk: Bus 0, device 18, function 0: Network controller: Digi International Datafire Micro V (Europe) (rev 2). IRQ 17. Master Capable. Latency=16. Max Lat=16. I/O at 0xe400 [0xe407]. Non-prefetchable 32 bit memory at 0xd8021000 [0xd80210ff]. i still receive error messages continuosly (every few seconds) i

What happens if you change to: signalling=bri_cpe_ptp -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Alex Sent: 01 October 2010 11:37 To: asterisk-users at lists.digium.com Subject: [asterisk-users] debian/dahdi/zaphfc - Unable to receive TEI fromnetwork! Hello, <snip> # cat

Hi i've an hfc-s card with last bristuff installed at cli> i'm receiving: Sep 8 12:35:20 WARNING[1109552048]: chan_zap.c:6902 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 received TEI check request for TEI = 77 what is causing them? 10x Maurizio

Hi all I finaly set up a second * with two ZapHFC Cards. One in TE the other in NT mode. So I have a 1.2.5 Asterisk to run Meetme etc... and a 1.2.4 Asterisk to run all that Zaptel stuff. First I used mISDN on 1.2.5 which worked, but sometimes had strange behaviour. So my hope was that zaptel is more stable... It steams realy stable in TE mode. No problem there. But I get a very strange

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

We have 2x BRI's connected to Asterisk which give us a total of 4 lines (using the bristuffed package). We would like to limit the number of incoming calls to 2 calls and if a 3rd call comes in, we would like this to go to another extension (voicemail or similar). Is this possible in Asterisk? Thanks -- James Doherty - Systems Engineer Zeald.com - Websites That Work! Web: www.zeald.com | Ph:

Hi all, In our asterisk box we have a Fritz card and an HFC card. So far I've had the Fritz card working well, but its time to connect the HFC card up to the ISDN line and get it working. I've followed the instructions on voip-info.org here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install and here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install But when it comes to

Hi. I'm running some asterisk boxes on different sites, some equipped with a couple of ZapHFC cards, others with Junghanns quadBRI cards. All boxes were compiled with Asterisk 1.2.10 (libpri 1.2.3 zaptel 1.2.6) and bristuff 0.3.0 pre 1s, distribution is Fedora Core 4 with kernel 2.6.17.3 The cards are connected to Telecom Italia's NT1/NT1+ S/T lines; some of them are point-to-point,

Hi, I have a partial working installation with zaphfc. Incoming call : For incoming call, seems work fine. But the sound is very bad with bounce short crashing sound. Same sound with echo cancel off or on. SDA work fine. Another problem, it's seems that's zaphfc don't reset correctly the line. I have one of my D channel how was busy even after stop communication. Outgoing call :

Hi, I've been learning asterisk for a couple of weeks now - and it worked for me as faar as standard configurations where concerned (sip/iax outbound/isdn4linux & capi with AVM Fritz!, Digium X100P FXO). Now I recently I'evaluating to use asterisk as a replacemnt for our companies (15 employees) legacy pbx system and I'm experiencing multiple problems with the hfc isdn cards:

I have Asterisk RC2 setup here with a Fritz ISDN card on Debian Woody. I'm using chan_capi-0.3.5 and fcpci-suse8.2-03.11.02. Settings are pretty much the default, except in order to get the fcpci module to compile, I had to follow the instructions here: http://www.voip-info.org/tiki-index.php?page=Asterisk%20AVM%20Fritz%20CAPI%20Driver%20Install but the drivers would only compile if I left

I'm using a Grandstream IP phone to call someone through our asterisk pbx. The PBX is running "Asterisk 1.0.3-BRIstuffed-0.2.0-RC3" and uses 2x ZAP-HFC cards. When I call someone, if the call isn't answered and then I hang up, I get "487" coming up on the grandstream phone. If I pick up the receiver again and then hang up, the PBX starts calling me back and when I

We have an office full of budgetones and find the ringing volume to be too loud especially when all the phones are ringing at once on an incoming call. I've tried setting the volume on each phone but the volume setting doesn't survive through reboots or power offs. Has anyone found a way to make the volume setting stick? Thanks -- James Doherty - Systems Engineer Zeald.com - Websites

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at