similar to: Codecs and negotiations

Anyone having problems with Stanaphone registration today? I'm getting the following.. Nov 25 11:35:58 NOTICE[229390]: chan_sip.c:4053 sip_reg_timeout: Registration for 'xxxxxxxxxx@216.128.82.18' timed out, trying again -- Got SIP response 500 "Internal Server Error" back from 216.128.82.18

I am trying to get Asterisks to connect to our StanaPhone so that I can use it to route my outgoing PSTN calls to. We have a free account and if I can get this working are willing to pay for an actual minutes with them. Here is what I have in my sip.conf: [stanaphone] type=friend secret=pAsSwOrD ; skewed for this message. username=3475341914 host=sip.stanaphone.com

Sorry if this comes thru twice, I had the wrong account selected to send the first time... Callers to the number get ringing, I get stuff in my asterisk console, and it calls my softphone and ata, but answering either gets silence, and the caller gets the ringing stop, if they wait ages they get the stanaphone voicemail. I have had the account for ages, and it never has worked, other sip

Hi, I am pretty new to all of this but was able to set up an asterisk server and have been able to succesfully connect to asterisk with x-lite as sip client. I have also connected asterisk to FWD (using iax2) and to voipjet (also using iax2). Now I am trying to connect asterisk to Stanaphone. It has to register as a SIP client but I am not being succesful at all. My asterisk server sits behind a

I have been running Asterisk for years on a machine with a public IP. Most recently, I have been running 1.2.17, from the day it came out, with no (noticeable) problems. Yesterday, I switched over to a new server that is on the same public subnet, one higher than the original server. I built 1.2.17 from source on that machine (as I did on the old server). My firewall on the new machine is

Hello, After much searching of voip-info.org and google, I'm finally giving in and asking the list. The setup I have is this:- Single X100P card in a Debian system Inbound/Outbound POTS line connects to the X100P Sipura 2000 and Budgetone 100 on the LAN 1 Cordless and one conventional phone connected to the sipura Account on Stanaphone.com for eitherbound SIP calls. (I have other SIP

I see that stanaphone is not accepting new customers. Does anyone know if they are doing ok? I have a number with them and would like to start redirection people before it gets canceled on me if they are having trouble.... thanks Todd

Now that I have most everything actually working I've noticed that about every 3-4 days on average..... and at worse... Once a day my asterisk box seems to lose it's registered state with our sip provider and no longer will take any incoming calls. The caller simply hears a fast busy (reorder) If I do a reload at the command prompt all is well for another few days..... What I'm

I'm going to try and ask this again and keep it short and as too the point as I can while still providing enough info to be of use. PLEASE advise if I am going about this wrong or asking too much. I'm seriously doing my BEST to throughly read the docs and try a bunch of things BEFORE coming here to ask and possibly annoy. If is documentation that explains thsi process in terms that

Dear List members, After succesfully installing the * on a couple of systems, and putting them on test, I observed that there is an intermittent call drop on PSTN line. The systems are - Dell Optiplex P3/500MHz/128MB - Built-in ethernet - 1 X100P (Motorolla chip) card on PCI - 10G HDD etc. - Asterisk April 17 CVS. - 2 Mediatrix FXS ATA (4 phones) - 2 Grandstream phones. - sip.conf, zaptel.comnf

Does IPKALL still exist? I am after a free SIP trunk - who is still giving these away these days? As I noticed Stanaphone is no longer in business? Regards, Dean Collins Cognation Inc dean at cognation.net <mailto:dean at cognation.net> +1-212-203-4357 New York +61-2-9016-5642 (Sydney in-dial). +44-20-3129-6001 (London in-dial). -------------- next part --------------

Here's a question I haven't seen asked nor answered on this list: Is there a provider who offers incoming 900# services? I want to establish a 900# to be used in (about 60-70) domain registrations, to deter telemarketers from calling yet still comply with ICANN requirements for a valid phone number. Alternatively, does anyone know of a source for super-low cost DIDs (like free

Hi, Does anyone have suggestions hooking Zyxel Prestige 2002 to Asterisk? I have tested Zyxel Prestige with both supported codecs. Call with G.711 sounds very choppy and cracking. Almost can't understand a word. Today I installed G.729 support into Asterisk but unbearable voice quality remains. It's a little bit better though. I have tested that Zyxel ATA with some commercial SIP

I have a lot of experience, all of it pretty good, with various Sipura products, Grandstreams, Zultys, IAXy, and numerous SIP/IAX soft phones connecting into Asterisk as clients. Good sound quality, great reliability. I've tried two of the units named in the subject line, and frankly I'm frustrated. Calls usually start out OK, but within a brief period the sound goes totally to

Hi all, Is there a possibility to set the codecs Asterisk will choose in the dialplan ("exten=>" statements or their contexts) instead of sip.conf? My problem is that I connect my SIP phone with several providers (Nikotel, Sipgate, Stanaphone) for icoming and outgoing calls. Not all of these providers offer the same set of codecs. I'd like Asterisk to use the same codec for the

I was previous using Asterisk 1.2.9.1 and decided to get some real servers outside of my house. It was time for Asterisk 1.4.4. I figured since all the conf files were in /etc/asterisk form the old box, i'd just copy tha directory over to the new server. My SIP DID AGI stuff worked, except running 'asterisk -r' doesn't. It tells me ' Unable to connect to remote asterisk (does

i would like to carry some oversea pstn-destinations via sip to providers like stanaphone, however, in case of a network-failure or if the provider is not available, i want to fallback to the zap-channels so the call is carried out to the pstn directly. the usual approach would be to check the dialstatus(e.g.NOANSWER). however, asterisk tries >60seconds to reach that peer(even when the ip

Now this is really frustrating. Everything was working fine, and now it isn't ... I don't think I've changed anything that would affect this, but I guess you never can be too sure. My setup is as follows: SIP softphone (SJphone) connected to Asterisk running my Linux NAT firewall box. This is all on the internal network. Asterisk then dialing out through various means - SIP to

All, I signed up for a broadvoice BYOD plan over the weekend (very excited about their offering) and after about an hour I had asterisk registered and was making in and out bound calls. However, the next day (without changing anything) I couldn't call in or out and haven't been able to get it going again. I can connect using a softphone (X-Lite) and make calls in and out

Hi.. I just wondering why DTMF are not recognized by aterisk on incoming calls from my SIP provider ... ANy suggesteions ?` /Mike