similar to: Asterisk <-> WellGate 3502a : ulaw/alaw only?

I'm loosing hair at cosmic speed now for the past 10 days. Welltech's Wellgate 38xx/35xx FXO/FXS SIP hardware versions seem to have very buggy firmware possibly due to hastely done porting from H.323 firmware. Is there anyone on this mailing list who was able to: 1. setup a 35xxA FXS with all ports authenticating properly with *? or 2. setup a 38xx FXO to work as dial-in from pstn to

Greetings, Is there a way to tie a specific sip username to a IP address when authenticating against mysql sipfriends table? (USE_MYSQL_FRIENDS=1 USE_SIP_MYSQL_FRIENDS=1 in channels/Makefile) The reason is that I'm using Wellgate FXSes that have second/third/fourth FXS ports bugged when I use a password, but work ok when there is no password. Linking the username to a specific ip could

Recently, there're some posts about registration problems with this gateway. These are my observations using the latest firmware version 107a. a) The gateway will register all 4 ports if you're not using password. b) If using password, the gateway will only register the 1st port correctly. For the record, the 2-port 3502 doesn't exhibit this behavior. FYI.

Hi again, Kind of sheepish about asking for help, as I have only spent a day banging my head off this... I got my new Welltech 3701a, 1FXS,1FXO gateway. I flashed it with what is seemingly the appropriate firmware (SIP V1.04). This seems to have gone ok, and it is now registering both ports ok with asterisk. For 1 minute I thought I was home free and and everything was just going to work

Any feedback on this brand and in particular on doing business with WelltechUSA? I am looking to the Wellgate 3701A which is a 1FXS-1FXO arrangement. I am hoping to replace the near worthless Grandstream HT-488. This company is telling me that I need to wire $ directly into there bank account. Most unusual. Thanks for any feedback on this, Marty

I got a Wellgate 3804A and need some hints: Both have public IP *.131=asterisk (1.6.0.1) *.133= Wellgate Wellgate 3804A settings (Line1~Line4): 1. Sip Config Mode: Proxy Primary Proxy IP Address: *.131 Primary Proxy port: 5060 Line1 Number: 1002 2. Security Config Line1 Account: 1002 Line1 Password: ****** 3. Line Configuration Line1: Type=FXO, Hunting Group=2, Hot Line =

Where I can find the firmware for the Wellgate 3804 ? The files are: - 2m4sipfxo.103 - 4fxosip.103 I don't have a password to pick up it at the welltech site. Kind regards, Miguel

I am interested in the wellgate 38XX FXO and FXS gateways (and other similiar units). My question is can outgoing call files use these devices??? Can I fashion an outgoing call file with a channel like: SIP/WellGate-1/5551212 (for the first port) or SIP/WellGate-2/5551223 (for the second port) TO these devices behave this way? Of course incoming calls I dont see as a problem. It's asking

Anyone know how to set the wellgate unit so incoming calls pass on directly to asterisk? Right now incoming calls ring twice and I hear a recording saying enter the extension. If I go enter the extension it goes on to asterisk just fine. I just want the incoming call to go directly onto asterisk. Anyone found that out? Jerry

I have a new wellgate 3802 unit. I have not gotten it to register with asterisk 1.2.6. My proxy setting is the correct IP in the 3802. My security config is 1001/1001 and 1002/1002 on the wellgate (simple at this time). My sip.conf has: [wellgate3802L1] type=friend dtmfmode=inband username=1001 secret=1001 host=dynamic canreinvite=yes nat=no context=wellgate [wellgate3802L2] type=friend

Hi there I have some problems in setting up a connection between * and a Wellgate 1501 (1FXS). Either I can dial from * to my Wellgate or I can dial from the Wellgate to *. On the Wellgate you have to setup both "Line number" (which is the number it answers) and "Line account" (which is the account it registers as). Should I expect any problems if these are set the same?

hey * folk, am trying to configure a WellGate 3504A FXS SIP ATA (http://www.welltech.com.tw/products_ea01.htm) with asterisk. i've set up two SIP clients in sip.conf as follows: [general] port = 5060 ; Port to bind to bindaddr = 0.0.0.0 ; Address to bind SIP channel to context = default ; Default context for incoming calls [1235] host = dynamic secret = somepass context = default type

Hi there I have a Welltech Wellgate SIP device and I want to be able to do a supervised transfer. I've read that in order to do that I have to use flash hook. The problem is just that I can't flash hook with this device. I'm in contact with the developer of the SIP device but don't know what to tell him in order to get him to fix this. What is happening when you flash hook, I

Ok this is a simple question... What has been your experience with the WellTech 38xx series (I'm looking specifically at the 3802) VoIP gateway? I'm looking for a good (and hopefully not too expensive) VoIP/T.38 gateway for my office. Asterisk intergration is not a major factor at this time but may be later on. How well does it work? Is Echo a problem? Do the T.38 capablities

Whoo hoo! I just received my WIP300 from voipsupply. I have to let it charge before I can play with it. A few quick comments: - I started a Wiki page at voip-info to post issues, firmware news, etc. I really like the wealth of info on the GXP-2000 page, so I wanted to start something similar for this phone. http://www.voip-info.org/wiki/index.php?page=Linksys%20WIP300 - My kit

I have a problem with my Welltech Wellgates. I can't call any extension which starts with or includes * or #. When dialing it responds fine but after some seconds I just get a busy tone and on the Asterisk console it says "SIP/2.0 484 Address Incomplete". Don't know if it connects to the DTMF payload type. Yesterday I made som different tests and observed that if DTMF payload

Dear Colleagues, I installed a Wellgate 3804A and overnight lines on all this with frying, putting other lines Wellgate 3804A is well, so I guess it's a problem the first team which is already out of warranty, anyone know how can I fix this? or where to send it in or capital Buenos Aires to fix it? Thanks Mart _________________________________________________________________ Todo

Hi again, I am trying to get my DTMF to use RFC 2833 rather then inband, so that I can utilize lower bandwidth codecs through my FXO. After much tinkering I was able to get my gateway (wellgate 3701A) configured to a point where I have some success, but no real joy. I have configured the RTP Payload type (or RFC2833 Payload type) to 101. I don't have a clue what this means, but I took

> From: "John Hughes" <john at calva.com> > To: "Asterisk Users Mailing List, Non-Commercial Discussion" > <asterisk-users at lists.digium.com> > Sent: Thursday, May 14, 2020 2:10:45 AM > Subject: [asterisk-users] I can do alaw, ulaw and gsm; remote can do g729 and > alaw; asterisk wants to translate g729 -> alaw. WHY? > I am having a

On 14/05/2020 08:10, John Hughes wrote: > > I am having a problem with one of my callers who is using either g729 > or alaw.  I can do alaw but not g729 so asterisk should negotiate alaw > right?  In fact from the sip debug it looks like it does, but then I > get the dreaded "channel.c:5630 set_format: Unable to find a codec > translation path: (g729) -> (alaw)"