similar to: Call Groups

Hello, Since outgoinglimit is EOL'd, I've implemented SetGroup/GetGroupCount to ensure that SIP clients will only have a single call at any time. Works perfectly for simple calls using Dial(). I'm now struggling to find a way to similarily limit 2nd calls to SIP clients that are Agents, who receive their calls from a Queue(). Is there any way to accomplish this (without writing

Hi, I seem to have a problem with chanisavail and the call limits on sip phones(incoming and outgoing) The problem seems to be that chanisavail when trying create to create channels and hanging them up afterwards screw up the current usage limit on the phones. Example with chanisavail: Phone A calls voicemail (usage now 1) Phone B tries to call Phone A and uses ChanIsAvail in the dialplan.

Hello, I'd like to be able to see if a channel is use and handle the call differently if it is. The best I can find is the command ChanIsAvail(). The problem is, I have an snom200 phone which does call waiting, so even if it is engaged in a call, a second channel is still available on it. I would like to be able to differentiate between these two cases: no calls engages, or calls

Hi Akk, If this has been discussed/done then apologies be-4-hand. I did not find it in the Wiki or the Archives. Here's the question. We have incoming PRI lines, all on the same main number. An attendant is supposed to handle all incoming calls. Now, let's say I have a multi-line SIP phone. For argument's sake (and to keep it simple) say I only have two lines. We'll call them

I got a Uniden UIP200 and started to configure it and I am lost.... I have a tftp server setup on my * server and have the files unidencom.txt and uniden<mac>.txt there. But it doesn't quite work yet. It registers as a sip phone (sip show peers), but I cann't dial it and the display shows #1 disconnected all the time. It has firmware version BS4.59a in it. I have no idea if I

I have 2 issues which I need to resolve on our production Asterisk server: We are currently using Polycom IP600 VOIP phones for our office which are capable of handling 2 calls per SIP registration. What we're finding is when staff are on the phone, Asterisk will pass them a second call which will show up on their display, and an audible beep is heard over the phone (regular call waiting). I

Hi folks, As none of the SIP softphones that I tested can disable more than one incoming call, I decided to implement it by software ;-) I'm attaching a patch that does it. To make it work, modify your sip.conf file and include callwaiting=[0|1] at the general section, or for each peer that you wish to control. Please note that I haven't tested it too much, and my source tree is quite

Hello, is there a way to disable call waiting in sip? I`m using grandstream 101 and even when the phone is in use I hear ringing in the headset. It is pretty annoying , is there some way to disable this? I cant find anything like it in the grandstream docs. Thanks -- Anton Yurchenko<phila@dg.net.ua> Digital Generation

I would like to setup a hunt group, not a group ring, using sip phones. Anyone done this with sip devices? Comments suggestions? I have not had much luck with the outgoinglimit=1, incominglimit=1 stuff that I would need to get busy extinctions to work right, which is why I'm asking on the list.

Hi all, I'm working on a setup for a small office. I'd like to use SIP/iconnecthere most of the time, because they're cheap. But they only allow a single call. When the single iconnecthere line is in use, I'd like to use IAX2/voicepulse instead: exten => _1NXXNXXXXXX,1,Dial,SIP/BYEXTENSION@iconnect exten => _1NXXNXXXXXX,2,Dial,IAX2/npI42VoD38@voicepulse/${EXTEN} Well,

Is there a way to trigger an action when a certain number of zap channels are in use, or is there a variable that stores max used channels that can be read? I use PRI for inbound calls, but outbound goes out via SIP, so the simple solution does not work. I need to know when the potential exists for inbound calls via PRI/Wildcard to be blocked because there are no more channels. Obviously

Let's say you have a 256 Kbps Internet connection and you're using it for voice calls. With mu-law (G.711), each call uses about 80 kbps, so you really can't have more than 3 calls active at one time. Does Asterisk support any kind of Call Admission Control where it would prevent you from originating a call if it would exceed your Internet bandwidth? For example, in this case, ideally,

It seems that when setting qualify = 200 or qualify = yes in the database for a sip friend/peer, RealTime does not update the registration status like it should. I also have several peers which have been offline and Asterisk still reports them as registered, even though the registration seconds are only 200. Asterisk Ver: CVS HEAD 12/1/2004 Layout of sip_buddies: mysql> describe

Hi folks, Can R-Project be used to perform Banker's Algorithum? http://en.wikipedia.org/wiki/Banker%27s_algorithm Pointer would be appreciated.  TIA B.R. Stephen L [[alternative HTML version deleted]]

Hi All After a Dial() I get: WARNING[7964][C-000075a8]: app_dial.c:2437 dial_exec_full: Unable to create channel of type 'SIP' (cause 20 - Subscriber absent) if the subscriber is not registered. Is there a way from dialplan to know, *before* Dial(), if a destination Subscriber is a) not registered or b) busy ? I need to redirect a call to some other Subscriber if (s)he is not there

I have the following dialplan (segment) that isn't working as I expected it to: exten => s,n,Dial(Zap/1&SIP/202&SIP/203,18) exten => s,n,Dial(Zap/1&SIP/201&SIP/202&SIP/203,42) The plan was to have SIP/201 added to the group of ringing phones after 3 or so rings. What ends up happening, though, is the Zap/1 phone STOPs ringing when the dialplan falls through to

Not being an asterisk expert, but having been around the block once or twice when it comes to data and the like, I have made some observations based on the examples given on voip-info.org Sip configs. it appears there is an adjustment to be made in the sip_buddies example table: >>> name Although set to 30 characters, I don't see where it is limited in the text file. In theory,

Hi all, I am just scratching my head trying to work out a way to use SetGroup to check busy status on a sip to sip call. The complication is that one call can't be in two groups so I have got no way of setting busy status on both the calling and called party. Has anyone got a way around this. Thanks Daniel -------------- next part -------------- An HTML attachment was

Hi, I have been trying to get my * box to limit an extension to one line for either an inbound or outbound call anyone got a quick example I can look at or a good howto? Cheers, Dee

Hi, I'm running 1.2 beta1 in a mini call center. I have 3 queues with 10 operators, and I'm running into some trouble because when all the operators are busy answering call asterisk still sends them more, resulting in a "beep beep" (call waiting) over and over again in Xlite audio. An easy solution woud be the use of a "single line" user agent, like firefly, still