similar to: Spellcaster ISDN BRI card

Hi, folks! Sangoma has an informal user survey up on their home page (at http://www.sangoma.com) asking if people would use their A500 card for North American BRI, if it were supported. I encourage anyone with an interest in voice BRI in North America to vote; this information will be used for deciding whether to make the investment in developing a National ISDN driver layer for it. Benefits to

Hi All, I currently run asterisk in our office (in Japan) and use a cisco PRI gateway for connection to the PSTN. I would like to setup some more systems for our smaller offices (in Japan) that would use BRI and preferably using a PCI card in the asterisk box and not a seperate Cisco gateway (expensive). HOWEVER, Japan has this INS64 protocol for their BRI lines and im not sure what cards

I would like to integrate * with an existing Altigen PBX. I want to spend as little money as possible to make it happen. My main goal is to inexpensively connect a branch office to the phone system. Eventually I would like to replace the Altigen system with an Asterisk server so I don't want to spend any money on Altigen hardware. Currently the Altigen has analog interfaces with a couple

Hello I want to setup an Asterisk in several offices with 4 BRI ISDN. I am looking for recommendations on hardware. Criteria would be ease of setup, reliability and cost. The Eicon 4 BRI cards seem fairly pricey. Shame Digium don't do a ISDN BRI card. Angus -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

Hello, I'm looking for an ISDN BRI-U interface for use in the US. I'm primarily interested in using the BRI as a trunking interface into the PSTN with Asterisk. Naturally, cheaper is better. I currently use a Nortel Norstar system with BRI-U trunks, and really like the digital PSTN interface. Would really like to replace the whole mess with Asterisk but want to keep the ISDN trunks.

Did you get this working I'm having the same issues. Sean -----Original Message----- From: Geoff Nordli [mailto:geoffn@gnaa.net] Sent: 22 September 2004 18:29 To: 'Asterisk Users Mailing List - Non-Commercial Discussion' Subject: [Asterisk-Users] make update and upgrade failed with `ZT_EVENT_POLARITY' undeclared Hello everyone. I am trying to do a cvs update. I do the make

Hi All, Has anyone had experiences with Asterisk and ISDN Gateways or cards? I am looking to setup a home phone system using asterisk and am looking to convert my two existing no's to a single isdn2e line. I was wandering if anyone could recommend which is better to use with asterisk - ISDN Card or gateway? also which brands are best with linux/asterisk? I have used eicon BRI cards for

Looking for folks experiences with ISDN BRI cards in the UK ... what's good and what's bad and any gotchas. Thx -- David Gurr Congruity Ltd. Hemel Hempstead UK

Hi, Bristuff works great with HFC card... your compilation problem may come from your kernel configuration... You should check this doc, at least, for the redhat config : http://www.automated.it/guidetoasterisk.htm Then, installation of Bristuff works like as charm ! Bye David Masure -----Message d'origine----- De : vdasilva [mailto:aquamoon@wol.co.za] Envoy? : mardi 28 juin 2005 09:01

Hi, I'm looking for an interface card for termination of Euro-ISDN2 (BRI) lines. That is ISDN lines from the telco into my Asterisk box. Any recommendations, good/bad expiriences ? At present I'm looking at cards from BeroNet and Junghanns. Cheers, John Faroese Telecom

Anyone have any experience with a R510 with the PERC H200/H700 controller with ZFS? My perception is that Dell doesn''t play well with OpenSolaris. Thanks, Geoff

Hi, I have very limited experience with BRIs, and now I have a project which requires to hook up an asterisk server to a client's Simen Hicom PBX with 32 BRI ports. In this regard I am looking for the right ISDN-BRI cards which I can install in an Asterisk server. I need two types of cards, one which could support 2-wire U2b1 interface and two which could support 4-wire S0 interface. Kindly

2015-05-26 12:17 GMT+02:00 Lukasz Sokol <el.es.cr at gmail.com>: > Hi, > please whoever has some expertise in choice of BRI ISDN cards, > please restore my faith in community support :) > > (on private email I can probably explain more than fits for a public forum) > > Most I'd like to ask is about what to choose, out of what is available... > > My locality is

Thank you all for valuable input, another question: when do I actually need the echo cancellation (hardware / on board /on module ) ? Lukasz On 26/05/15 11:17, Lukasz Sokol wrote: > Hi, > please whoever has some expertise in choice of BRI ISDN cards, > please restore my faith in community support :) > > (on private email I can probably explain more than fits for a public

I am considering a G5/XServe for a conferencing system. I need to put a TDM card in the machine for timing. Is anyone out there using Asterisk on Mac with zaptel drivers? I am looking at using Linux for the OS. If so what is your experience? Have a great day! Geoff

I am trying to configure a system where I have two different NFS shares which point to the same directory. The idea is if you come in via one path, you will have read-only access and can''t delete any files, if you come in the 2nd path, then you will have read/write access. For example, create the read/write nfs share: zfs create tank/snapshots zfs set sharenfs=on tank/snapshots root

Hi all Hi,I'm facing a strange issue where by SANGOMA not detected by goautodial system , Thats the problem : Configuring ISDN BRI cards [A500/B700] ------------------------------------ No Sangoma ISDN BRI cards detected Press any key to continue: ------------------------------------ Configuring GSM cards [W400] ------------------------------------ No Sangoma GSM cards detected

> Thank you all for valuable input, > > another question: when do I actually need the echo cancellation > (hardware / on board /on module ) ? > It depends on your environment. If there are still analog devices in addition to VoIP, I'd say always, but Asterisk has a rudimentary echo canceller already on board. The Telcos use echo cancellers themselves, but it cannot hurt to

Hi Everyone. Asterisk is one of those applications that need to be built from cvs on a regular basis to keep up with the changes. I have always used package management tools like apt. How does everyone manage their Asterisk servers? Geoff