similar to: No Caller Name sent from Asterisk over National or DMS100 PRI to a Norstar MICS?

All good information, thanks. However this is private network between Asterisk and a Norstar MICS about six feet away. So I'm holding both ends of the link. :-) > -----Original Message----- > From: David Troy [mailto:dave@popvox.com] > Sent: September 16, 2004 4:57 AM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: Re: [Asterisk-Users] No Caller Name

----- Original Message ----- > Message: 3 > Date: Thu, 16 Sep 2004 07:57:15 -0400 (EDT) > From: David Troy <dave@popvox.com> > Subject: Re: [Asterisk-Users] No Caller Name sent from Asterisk over > National or DMS100 PRI to a Norstar MICS? > snip> > > I have a PRI link up and running between Asterisk and a Nortel Norstar MICS > > v4.1 . I'm having a

Hello all, I have Asterisk 1.2.1 and a TE110P connected to a Nortel Meridian Option 81C system. The PRI line is currently setup as DMS100. Here are the relevant lines from zaptel.conf and zapata.conf: zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone = us defaultzone = us zapata.conf: [channels] language=en context=from-internal musiconhold=default switchtype=dms100

To All; My current issues is a 5 second delay for call that is being transferred from the Norstar units to the Asterisk servers VIA a PRI. Is their anything that can be done to speed up the transfer on the Norstar. Below is my current phone config. < Norstar1 >----PRI----< Asterisk-1 >----IP-WAN----< Asterisk-2 >---PRI---< Norstar2> The Norstars are MICS 0x32 4.1

I am currently working on an Asterisk test system, and will be presenting a demo to the Board of Directors tomorrow night. I want to make sure I have all of my ducks in a row. The Asterisk system will be used to replace a Norstar MICS. The location has two PRI's coming in, with a few hundred DIDs. I know how to make * use the DIDs incoming, and I know how Nortel uses the DIDs. Now for the

Hello, Quick Diagram: Telco-PRI -> Asterisk <- Norstar PRI -> Norstar PBX (DMS100) (TE405P) (DMS100) | | V Cisco 7960G (SIP) I'm trying to change the Origination Number on my outgoing PRI, and running into a weird problem. If I make a call from a SIP extension off asterisk using the following context:

Hi, I dropped an asterisk server with a TE405P between a Norstar Meridian PBX and it's PRI PSTN connection. Everything seemed to work fine using a pass-thru-type dialplan configuration... except now we've realised that outbound calls to celphones get dropped upon connect, but not on every call (almost always the first try, but not the second). All other calls to non-celphones had no

So I reached the point where my PRI is accepting incoming calls, but I cannot dialout. I must be doing something stupid, but I can't figure it out. The Asterisk box is sitting between the Mitel and the phone company, and has PRI lines to each. Asterisk was built from CVS r1-0 Log for a call from mitel heading outbound: ------------------------- -- Accepting call from '' to

We have a DMS100 that does not have PRI. So we're using a channelized T1 using WU-LAW, ESF and B8ZS coming from the DMS100 that's plugged into a Tormenta2 Quad T1 Card on my Asterisk Box running Debian 3.01(woody) with Kernel 2.4.22. The Link is up but according to the DMS100, Channel_1 goes into RMB (Remote Manual Block) and Channel_2 goes into LO (Lock Out). I've been through all

I have not been able to get two B-channel transfer to work on DMS100 PRI. I consistently get the following errors: [Nov 6 11:12:49] ERROR[2774]: chan_zap.c:8178 zt_pri_error: ROSE RETURN ERROR: [Nov 6 11:12:49] ERROR[2774]: chan_zap.c:8178 zt_pri_error: OPERATION: RLT_OPERATION_IND [Nov 6 11:12:49] ERROR[2774]: chan_zap.c:8178 zt_pri_error: ERROR: RLT Not Allowed I have tried on two

Hi Folks, I'm trying to send CallerID Name information out to the PSTN via a PRI with Bell Canada with no success. With inbound calls (originating from the PSTN) CNAM is received successfully, and we've not had any similar problems with other Telco PRIs, so I'm stumped.

> -----Original Message----- > From: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com]On Behalf Of Gary Reuter > Sent: Thursday, August 11, 2005 12:59 PM > To: asterisk-users@lists.digium.com > Subject: Re: [Asterisk-Users] PRI dropped calls w/ asterisk dropped > betweenpstn & norstar > > > I poured over my logs most of

I've noticed a problem with calls to Hangup when talking to my Norstars over channelised T-1 E&M trunk lines - it's been present since I started to fiddle with Asterisk last December and it's still present in 'Asterisk CVS-HEAD-08/13/04-10:37:13'. Specifically, when a call is connected to Asterisk from the Norstar DTI card to my T100p I get the following conditions

Hi there! We have an old legacy norstar phone system m8x24-ds ( dr5 ) and a couple of m0x16. It has 5 external analog lines. It has no auto attendant, and no voicemail. So every incoming call is forwarded to a operator, she pick up the phone, talks to the caller and transfer the call to the right extension. We are in Argentina, so buying a star talk is out of the question, there is no selling of

Does anyone know which signalling protocol works when connecting the output of a NT8B90AL Norstar ATA2 analog terminal adapter to an FXO card? (fxsks, fxsgs, fxsls?) I'm trying to add an Asterisk branch to my Norstar PBX as outlined at http://www.voip-info.org/wiki-Asterisk+Nortel. - Mike

Hi, I have a legacy Norstar system that I'm looking into integrating with my Asterisk setup. My first attempts have worked, which involves a Wildcard X100P FXO card in the * box connected to the Internal ATA (FXS port) on the Norstar system. Calling from SIP -> Norstar works fine, since the SIP caller initiated the call and generally will be sane enough to hangup the phone when

I'm attempting to use an asterisk box with a Digium TDM01B as voicemail for an existing Meridian/Norstar PBX with an ATA-2 adapter. We're having problems where hangup is not always (but sometimes) detected. It's not detected probably 70% of the time or more. (The users transfer callers to an extension--caller then has to navigate a menu to get to the appropriate user). After

Hi all, I'm trying to insert a Rhino Ceros box equipped with a Rhino R2T1 dual-T1 card and running the latest version of Trixbox (2.4.2) between the central office and a Nortel Option 11. The switch at the CO is a DMS100. Basically, I'm taking the T1, connecting it to port 0 on the R2T1 card, and then connecting port 1 to the Nortel. (Actually a CSU and then the Nortel) We're running

Only a warning, and doesn't seem to do anything bad. But I can't seem to figure out what these warnings mean? -- Requested transfer capability: 0x00 - SPEECH [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: k [Feb 17 12:33:03] WARNING[10750]: chan_dahdi.c:3096 dahdi_call: Unrecognized prilocaldialplan NPI modifier: o [Feb 17

I'm testing an ivr implementation (first time) using: exten => 620,1,Wait,1 exten => 620,2,Answer exten => 620,3,DigitTimeout,5 exten => 620,4,ResponseTimeout,10 exten => 620,5,Background(npi-greeting) ; "Thanks for calling press 1 for" exten => 1,1,Goto(npi-directory,s,1) For initial testing, I've arbitrarily mapped this onto ext 620 (will change that later