similar to: Compaq cpqfc driver

Hello all I am trying to setup a backup system using Bacula on CentOS 6.7 installed on eserver x345 but cannot find the drivers Any help in finding the drivers will be much appreciated Regards Mustafa

Once upon a time, Mustafa Mohammed <netechie at yahoo.com> said: > I am trying to setup a backup system using Bacula on CentOS 6.7 installed on eserver x345 but cannot find the drivers I set one of those up many years ago, probably RHEL 3 timeframe. No drivers are necessary for the library, although you will have to find a differential SCSI card that is still supported to connect it

Hi everybody. I have an HP StorageWorks array connected to one of my servers, connected via an LSI controller (lspci reports: SCSI storage controller: LSI Logic / Symbios Logic SAS1068E PCI-Express Fusion-MPT SAS (rev 08)) on an HP DL385 running CentOS 5.5 x86_64. I have set up multipath and all is working but, when I create a snaphost and export it as a new LUN from the HP web interface, it

We just installed a new cluster with 6 HP DL380g5, dual single port Qlogic 24xx HBAs connected via two HP 4/16 Storageworks switches to a 3Par S400. We are using the 3Par recommended config for the Qlogic driver and device-mapper-multipath giving us 4 paths to the SAN. We do see some SCSI errors where DM-MP is failing a path after get a 0x2000 error from the SAN controller, but the path gets puts

Hello there I have been trying to install HP Storageworks DAT72 on CentOS 5 in vain. On system reboot, neither /dev/st not /dev/sg is available. May you please lead me through as this is my first time trying to do it lsmod Module Size Used by ipv6 267617 40 xfrm_nalgo 13381 1 ipv6 crypto_api 12609 1 xfrm_nalgo autofs4

Hi, I am looking for a vendor that can supply CentOS pre-installed on hardware as follows. _____________________________ Phenom AMD X4 processor 8 Gb of memory 250Gb HD or better dual-layer DVD writer reasonably good graphics card _____________________________ Please reply with a link to a list of vendors or anactual list and their contact info. Thank you, Kevin -- Kevin C. Abbey

Hi everyone, I have a Samba server on CentOS 5.2 that I would like to and some backup service to, I have been trying to install Bacula, because I want to backup MS machines too, and there is a web GUI. But when searching around i google I get a bit confused. about what packages I need. Has anyone got bacula running on Centos or maybe guide in the right direction. Tronn -------------- next part

greetings does the list at this url cover *all* options or are there some hidden or newer ones by chance? http://www.centos.org/docs/4/html/rhel-ig-x8664-multi-en-4/ap-bootopts.html i am playing with CentOS 4 on some Compaq dual PIII hardware. The first unit is an 1850R with dual 500Mhz. If you need more info please let me know. it is a basic unit with raid controller and a Gig of DRAM etc.

I notice from the hardware compatibility list that the XR model is supported - what are the chances that the older R3000h models are too? Thanks. /Per Jessen, Z?rich

I am trying to install x86_64 on a compaq r4000 laptop. booting the CD I have tried text mode only and graphicaly mode. I see the normal stuff flying by and I just get a black screen (in text for graphic install). I have tried linux acpi=off apci=off nousb nopcmcia linux noprobe all result in the same black screen. Once the screen goes black the CD is still being accessed but the screen is

Jerry Geis wrote: >/ I have tried in the grub.conf file />/ />/ noapic />/ />/ and />/ />/ apic=off />/ />/ I am still getting the same error message about ACPI />/ in the dmesg output. />/ />/ example: />/ ACPI: PCI interupt .... IRQ 16 />/ eth0: RealTek RTL8139 ... IRQ16 />/ eth0: identified 8139 chip type />/ />/ so ACPI is grabbing IRQ

Peter Bowen wrote: > If I use an initrd, the kernel will hang or panic right before starting > kswapd. The same kernel, if used without initrd will boot fine. On > other non-Compaq Proliant machines it works fine. > I have a guess as what this bug might be. Could you send me the E820 BIOS info for this machine, plus the sizes of the kernel and initrd? I'd like to verify my

Hello all, I have obtained a Compaq T700 H UPS sans-cable. My research indicates it would've come with a HP #201092-001 cable, and from previous posts on this list, it speaks upscode2, possibly being a rebadged Eaton unit. Any suggestions for cable pinouts I can try? Regards, Mathew McBride

Hi. I would like to install slackware linux onto my compaq tablet pc. the problem is that it doesn't have either floppy or cd-rom, but it does support booting from PXE or RPL. I was wondering if you can use the slackware install iso to boot via the network. Or do i have to do in another way? Thanks //Anders _________________________ ___m_ >><____('> enfisk.nu

Hi The man pages don't format properly on Tru64 unix for portable openssh. They come out as a solid lump of text. I managed to fix the problem by including the line .so /usr/local/share/groff/tmac/tmac.andoc (I have GNU groff installed) In the man pages. It appears the OSF -man option on nroff doesn't format the pages correctly. Thanks Jeremy -- Jeremy Sanders <jss at

I'm using OpenSSH_3.5p1 (server protocol 2.0 ) on a Compaq device V5.1A with C2 Security (SIA) configured. I must set UsePrivilegeSeparation to no to get this working. Does anyone have PrivilegeSeparation working on a Compaq device with C2 Security configured? Source device: ssh user at destination ( produces these errors) sshd: /var/tcb/files/__db_lock.share: Permission denied sshd:

I am trying to install CentOS 3.4 on a Compaq Proliant 1600, and it hangs on probing monitor type when anaconda starts. I have tried running 'linux text' and manually installing drivers from the f2 options screen. Any ideas? Forgive me if this is an unbearably simple question, but I am new to linux. Mike

On Jul 22, 2017, at 4:13 AM, Tomas Larsson <tomas.larsson at enrad.se> wrote: > > I am planning to install NUT (master) on a headless CENTOS 6.8 system. > Connect the UPS with seral cable. It looks like this might be using the upscode2 driver (UPScode-II protocol), right? > Now my main question is, Does NUT support the power segments on the UPS. > My intention is to be able

greetings pre centos install raid5 setup on a compaq dl380 is asking for stripe size. 16kb 32kb 64kb i am using one of the built in controllers and the machine has just a gig of ram and 4 18.2 gig 10,000 rpm drives machine will be an email server with simple web hosting as well. suggestions? thanks - rh -- Robert Hanson - Abba Communications Computer & Internet Services (509)

Anyone tried installing centos 4.2 on an compaq R4000? The CD boots, I hit enter, starts uncompressing the kernel detects my disks (last thing I see) then the screen is BLANK. I tried "linux text" also and exact same thing happens. THanks, Jerry