similar to: chan_h323: remote ip address -> context

Hello, Thank you for the job well-done. I installed the chan_h323 of the asterisk-1.2.7.1 and with lib pwlib-v1_10_0-src-tar.gz and openh323-v1_18_0-src-tar.gz and I used licensed g729 from digium. However, I am having a very funny behavour. 1. If I send a call on its ringing at the called side but the caller didn't get the ringing tone. 2. if the called picks up the phone, I am

Hi, I compiled asterisk and chan_h323 on an Opteron in 64 bit mode. In the h323's Makefile I replaced in line 24 CFLAGS += -march=$(shell uname -m) by CFLAGS += -march=k8 and also tried CFLAGS += -m64 -march=k8 Both solutions do compile, but when starting asterisk, a load error occurs: undefined symbol: _ZN14H323Connection24OnUserInputInlineRFC2833ER15OpalRFC2833Infoi When I grep

I am experimenting with oh323 channels and h.323 gateways and a Cisco CallManager. I am not using a gatekeeper at this time. Is it possible to place calls coming into Asterisk from specific peers into specific contexts? In iax.conf eaxh peer has a context in which I can specify the context an inbound call will be placed in. I don't see anything like this in the oh323.conf file or the oh323

I am trying to figure out the correct way to send my E.164 ID with chan_h323 and or chan_oh323 as my H323 provider requires this in the format of 'account-pin'. With chan_oh323 I have been able to register with the gatekeeper and can recieve incomming calls, but outgoing calls do not work. With chan_h323, I can call H323 clients (netmeeting, ATAs etc) but cannot place a call through my

---------- Forwarded message ---------- From: Tzafrir Cohen <tzafrir.cohen at xorcom.com> Date: Oct 4, 2007 12:56 PM Subject: Re: [asterisk-dev] chan_h323 and chan_oh323 compatibilities To: asterisk-dev at lists.digium.com Hi On Thu, Oct 04, 2007 at 11:46:30AM -0300, Caciano Machado wrote: > I'm receiving a lot of warning messages from my Asterisk > 1.2.5/chan_oh323 every time

Hi, I have been using chan_oh323 with a latency issue even on the same network. I am now trying chan_h323 and can only get one way audio. I am testing using SJPhone -> SJPhone, and also SJPhone -> 7960 (SIP). Any ideas? Must be something obvious that I am missing? Thanks. Regards, Steven Thomas

Hi, Has anybody managed to get callerid properly set on a call from local to asterisk SIP endpoint through h323-pstn gateway to a regular phone. I'm using ata186 as SIP endpoint. It has 12125551234 assigned to it. When I place a call to pstn I'm not receiving 12125551234 as the clid, but a number assigned to PRI channel by phone company. It worked with chan_oh323, but there were other

Hi, trying to build the h323 channel driver that comes with asterisk works fine, but only as long as I use openh323-1.11.7. Unfortunately, that setup seems to have a bug which misguides one of the audio streams. (So while * can "hear" me, the phone remains silent.) I suppose that bug is fixed at least in openh323 CVS. At least, I got things mostly working using the external

Hello! Tried to compile, but : [CC] chan_h323.c -> chan_h323.o chan_h323.c: In function '__oh323_update_info': chan_h323.c:349: error: dereferencing pointer to incomplete type chan_h323.c:350: error: dereferencing pointer to incomplete type chan_h323.c: In function 'oh323_rtp_read': chan_h323.c:790: error: dereferencing pointer to incomplete type chan_h323.c:791: error:

Hello all, I got the following error compiling h323 support in the latest cvs. Below the error is a diff to the file that I got to make it work. I took an example out of sip as far as the syntax for ast_rtp_new. Not sure if it is correct or not, but it seems to work. Please correct me if I am wrong in the additional 2 arguements. Regards, Scott cc -g -pg -c -o chan_h323.o -march=i686

Hi all, I try to ask helps again about chan_h323 extensions. I define this in h323.conf: [general] port = 1720 bindaddr = 0.0.0.0 allow=gsm allow=ulaw gatekeeper = DISABLE context=default [gm1] type=friend host=192.168.1.20 context=default [gm2] type=friend host=192.168.1.25 context=default and I have in extensions.conf : [demo]

Hi All, I am trying to build chan_h323 for use with asterisk 1.4.18 on Solaris 10. When I compile asterisk, the build fails at chan_h323 with: ---------------------------------------------------------------------- chan_h323.c: In function `reload_config': chan_h323.c:2863: error: `IPTOS_MINCOST' undeclared (first use in this function) chan_h323.c:2863: error: (Each undeclared

Hello List, I've been trying to compile Asterisk with H.323 support and, after correctly installing PTLib and H323plus (OpenH323), the Asterisk configure script still doesn't detect the dependencies as installed. I know they are correctly installed because after going into "[asterisk-source-directory]/channels/h323" and issuing a 'make opt', it correctly builds

Hi, We have been running asterisk in our telco interconnect box with ss7 and H323 configured. Everything ran find till now, however, today, it started crashing with the following messages: [Jul 28 14:56:55] WARNING[2968]: acl.c:541 ast_ouraddrfor: Cannot create socket [Jul 28 14:56:55] ERROR[2968]: chan_h323.c:962 __oh323_rtp_create: Unable to locate local IP address for RTP stream [Jul 28

Some of you may remember seeing my issue using SIP for incoming calls from the PSTN: http://voip-info.org/wiki-Asterisk+cisco+FXO i.e. all incoming calls arrive in the default 'bogon-calls' context. Well, I tried again using H.323 & get exactly the same result (both for chan_h323 & chan_oh323) i.e. all attempts to put a type=peer in sip.conf or a type=user in h323.conf for

What happened to chan_h323.c in the asterisk cvs? I got ast_h323.cpp, ast_h323.h and chan_h323.h but no chan_h323.c. Hence chan_h323.so was not created so no h323 support in asterisk. Just wondering when to expect it again because I was stupid and didn't make a backup of the asterisk code before wiping the directory for a rebuild. -------------- next part -------------- An HTML attachment

When the support for h323plus was announced for Asterisk 1.4.25, I tried to build this support in Asterisk. For this, I checked out the h323plus CVS from SourceForge, which reported version 1.20.beta5, and also the ptlib-2.4.2 source RPM from Fedora 10. I finally managed to build a chan_h323 for Asterisk 1.4.25, which apparently loads correctly, but now I see that I get a segfault whenever I

Hello, I installed Asterisk from CVS on Redhat Linux 9 and working with chan_h323 module and g729/g723 free codecs too. My network connection diagram: ---------------------------------------------- X-lite/X-Pro-->Asterisk--chan_h323-->GnuGK--->AS5300-->PSTN boldsoft*CLI> show version Asterisk CVS-v1-0-03/24/06-15:27:08 built by root@boldsoft on a i686 running Linux I can make

I'm having a problem with chan_h323 compiling for Asterisk. RedHat 7.3 PWLIB 1.4.11 pwlib_1.4.11.tar.gz OpenH323 1.11.7 openh323_1.11.7.tar.gz [asterisk@jonux h323]# make clean rm -f *.o *.so core.* [root@jonux h323]# make cc -g -pg -c -o chan_h323.o -pipe -Wall -fPIC -Wmissing-prototypes -Wmissing-declarations -DP_LINUX -D_REENTRANT -D_GNU_SOURCE -march=i686 -DPBYTE_ORDER=PLITTLE_ENDIAN

---------- Forwarded message ---------- Date: Wed, 11 Jun 2003 01:10:16 +0200 (CEST) From: Siggi Langauf <langausd@fachschaft.informatik.uni-stuttgart.de> To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] chan_h323 + openh323 CVS = no go? On Tue, 10 Jun 2003, Jeremy McNamara wrote: > If you would have followed the build instructions laid out by the Open > H.323 folks