similar to: FXO Disconnect supervision

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress enabled in * we are having a few disconnects while calls are in session (about 2 reported in first 5 days of use). I have talked both to

Simple question that google hasn't helped much with (likely poor search terms) I just installed a Sangoma A200 with overall good results. Initial tests with both incoming and outgoing calls were very positive. Until I made a normal call that lasted more than 30 seconds. I setup the FXO with kewlstart signalling, and the outgoing call is never registered as 'Answered' and the dial

Ok so this is officially driving me crazy. I have an Asterisk 1.6.1.6 install with DAHDI/DAHDI tools (latest) and an OpenVOX TDM400 card with 1 FXO port and 1 FXS port. I have a POTS line from my phone company attached to the POTS line. I have asked for "disconnect supervision" to be provisioned on my line and they claim to have added it. However, my scenario is as follows: I receive a

Can anyone help me with the term that SBC uses to refer to disconnect supervision? I have an Adit 600 channel bank which has helped improve the disconnect detection time down to about 8 seconds. This is still causing some issues in particular with call progress on we are having a few disconnects while calls are in session. I have talked both to some local phone contractors and SBC directly and

> > > > I would be grateful if anybody could tell me what I should > > tell Verizon > > in NJ so they would enable "disconnect supervision" for my lines. > > > > Apparently "remote hangup notification" or "disconnect > supervision" or > > "calling party control" is NOT the magic phrase for them. Although >

The FXO lines on my TDM400 are connected to PSTN lines in Israel. As far as I know, the lines around here have disconnect supervision (I've seen some other Israelis on this list, anyone know for sure?), because it's worked on Dialogic cards, which reported hangup, not busy detect (while when I connect a Dialogic card to a PBX, I have to measure the busy signal's frequency/cadence or

Hi, I am using TDM400 card with 3 fxs and 1 fxo. I am struggling to detect hangup tone or disconnect supervision tone from my CO. I attached the recorded wav file which contains my telco's disconnect supervision. I am using , asterisk-1.4.33.1 dahdi-linux-complete-2.3.0.1+ 2.3.0 OS => Debian-lenny 5 users.conf ------------- [trunk_1] trunkname = pstn ; GUI

Hi everyone, I've just got my X100P card installed and working but there seems to be an issue with hang-up supervision. If I stuff a call out over the X100P card onto the PSTN that's fine. When I hang up the SIP phone the PSTN call ends. If I receive a call from the PSTN, it's answered and everything is ok until the remote party hangs up. Asterisk thinks the call is still active and

Hey all, anyone know the status of disconnect supervision on POTS lines in India? Set up an asterisk box, TDM cards, in Mumbai, and doesn't seem to have disconnect supervision...... Thanks -- Chris Earle System Solutions Specialist

I'm starting to shop for my first channel bank and one of the features that eveyone seems to recommend is "far end disconnect supervision". What other terms do various manufactures use to describe this same feature ? Is "calling party disconnect" the same as "far end disconnect supervision" ? Thanks

Hi all I'm using sangoma a200 cards in the UK and have the ongoing, often noted problem of disconnect supervision with BT POTS lines. Just noticed this post on http://www.voip-info.org/wiki/view/UK+Asterisk+Details stating that potentially someone's got a solution : "TDM400P & Not Detecting Hangups: Got a TDM400P installed and having problems with Asterisk not detecting

Hi I know this gets covered fairly regularly, but I've had a search through the archives and can't find anything dealing with this specifically - apologies if I've missed it though. I've got a TDM11B with the fxo port plugged into a standard UK BT PSTN line, loading wcfxs with OPERMODE=UK. All's working well, except if I get an incoming call through my bt line, and the

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

I realise I am not alone in this, but I don't seem to be finding many solutions. I am running a CentOS box and * 1.09 with a TDM11B (1xFXS/1xFXO). Everything works great accept hang-up detection of incoming PSTN calls. * answers the call, but if the incoming caller hangs up, * does not release the line. I have determined the following information about my line: When On-Hook line voltage =

Hello, is there a full guide to what kewlstart is supposed to do with FXO or FXS lines ? is it only applicable to one of the interfaces FXO -or- FXS but not both ? I asked earlier if FXS lines can be made to reverse polarity, and someone else pointed out that the chipset on the FXS ports seems to support it, perhaps the driver in the asterisk zaptel interface module needs to be modified to support

I have a normal backup phone (and an alarm panel) sharing the POTS line with the Digium X101P FXO: | | Wall |>---+------X101P FXO as Zap/5 | | | Phone & Alarm Whenever the Phone is used, Asterisk sees a 'false ring' signal immediately when the phone is hung up. The Alarm panel dials out nightly at around 1AM, and each time it completes the call, Asterisk

Hi, I've just added an X101P FXO card to my asterisk machine. The card is detected ok but zttool always shows it in a RED alarm state, which I understand means that it doesn't detect the line. I've connected the card via the line socket to my analogue line using the cable that came with the card (and have also tried other cables too) but I always get a RED alarm. I'm located in

Hi, I installed a 1-port FXO on my Ubuntu 8.4. I was earlier only hearing a fast clicking sound and now I am not hearing any dial-tone. The FXO card has 2 slots: [phone | line ]. I hve connected the wall-phone-input to the "line" slot and "phone" to my home-phone. I do not hear any dial-tone on my home-phone. Asterisk seems to recognize my hardware....here are the relevant

Skipped content of type multipart/alternative-------------- next part -------------- No virus found in this outgoing message. Checked by AVG Anti-Virus. Version: 7.0.300 / Virus Database: 265.6.8 - Release Date: 1/3/2005

Hi. I am using Digium TDM2400PFXO with Asterisk1.6. When call sets in the box , it answers the call even the phone is not picked. ideally it should answer the call when the phone is picked up. Its charging the clients. Please let me know how can I cover this ? Thanks in advance. -------------- next part -------------- An HTML attachment was scrubbed... URL: