similar to: Can only call asterisk once

Hello, I?m trying to compile the Fritz CAPI module for Debian stable, following the steps related in http://www.voip-info.org/tiki-index.php?page=Asterisk%20AVM%20Fritz%20CAPI%20Driver%20Install But I always get the same error, debian-asterisk:/home/ismaelg/fritz# make (cd src.drv; make CARD=fcpci) make[1]: Entering directory `/home/ismaelg/fritz/src.drv' cc -c -DMODULE

I have a "Cologne Chip Designs GmbH ISDN network controller" in my asterisk box, and an ISDN line connected up to it. I downloaded the bri-stuff 0.1.0-RC4a package from junghanns.net and used that to compile asterisk using these instructions: http://www.voip-info.org/tiki-index.php?page=Asterisk%20zaphfc%20install When I try to call my asterisk box, my sip phone rings twice and then the

Hi all, In our asterisk box we have a Fritz card and an HFC card. So far I've had the Fritz card working well, but its time to connect the HFC card up to the ISDN line and get it working. I've followed the instructions on voip-info.org here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install and here: http://www.voip-info.org/wiki-Asterisk+zaphfc+install But when it comes to

Hello, I?m trying to compile the Fritz CAPI module for Debian, following the steps related in http://www.voip-info.org/tiki-index.php?page=Asterisk%20AVM%20Fritz%20CAPI%20Driver%20Install But I always get the same error, debian-asterisk:/home/ismaelg/fritz# make (cd src.drv; make CARD=fcpci) make[1]: Entering directory `/home/ismaelg/fritz/src.drv' cc -c -DMODULE -DMODVERSIONS

We have 2x BRI's connected to Asterisk which give us a total of 4 lines (using the bristuffed package). We would like to limit the number of incoming calls to 2 calls and if a 3rd call comes in, we would like this to go to another extension (voicemail or similar). Is this possible in Asterisk? Thanks -- James Doherty - Systems Engineer Zeald.com - Websites That Work! Web: www.zeald.com | Ph:

Hi Everyone, Long time reader, first time poster. FINALLY got my First AVM Fritz Card up and running under Centos 3.4 Installed the second....modified the drivers etc as per the instructions found at the wiki System boots Modprobe capi all good modprobe fcpci all good modprobe f2pci the kernel then goes into Panic If Modprobe f2pci before fcpci the kernel still goes into panic.

I'm using a Grandstream IP phone to call someone through our asterisk pbx. The PBX is running "Asterisk 1.0.3-BRIstuffed-0.2.0-RC3" and uses 2x ZAP-HFC cards. When I call someone, if the call isn't answered and then I hang up, I get "487" coming up on the grandstream phone. If I pick up the receiver again and then hang up, the PBX starts calling me back and when I

We have an office full of budgetones and find the ringing volume to be too loud especially when all the phones are ringing at once on an incoming call. I've tried setting the volume on each phone but the volume setting doesn't survive through reboots or power offs. Has anyone found a way to make the volume setting stick? Thanks -- James Doherty - Systems Engineer Zeald.com - Websites

All, I have been trying to get CAPI4Linux working on my machine and being frank am failing miserably! I am looking for any help available, I am real newbie (so please be gentle) and choose to run Mandrake 9.2 as it appears quite friendly (or so I thought!). I have been following the guidance found at http://www.voip-info.org/wiki-Asterisk+How+to+connect+with+CAPI for the AVM card (actually I

Hi I use RH 9 + asterisk v1.0 stable + 2 PCI fritz cards + chan_capi 3.5 and it works fine, Since my users want fax fonctionnality and customers know 1 of the msm as fax number I wanted to try the chan_capi-0.3.5 patch if I patch chan_capi and run make, I get an error message , as you can read below, orginal chan_capi compile works, when patched I get an error, no CID ? Any idea ? anybody

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Not strictly Asterisk related, but I'm trying to get an AVM Fritz! card to work with Asterisk on a Fedora Core 3 box. I've grabbed the official AVM Fritz CAPI driver from the AVM website and compiled against the current kernel. However, as soon as I modprobe it I get: CAPI Subsystem Rev 1.1.2.8 fcpci: module license 'Proprietary'

HI all, Has anyone succesfully installed an AVM Fritz! card on Fedora 7 using the drivers at ATrpms recently? http://atrpms.net/dist/f7/fcpci/ I tried with a clean F7 build on my EPIA 5000 yesterday, after modifying /etc/capi.conf (removing the coment # in front of fcpci line) I received the following error when executing 'capiinit' - FATAL: Error inserting fcpci

So I've got a PBX running with one Fritz card with the fcpci module and that works fine, but add another one and... kersplat... Kernel Panic. It boots fine with two cards, but panics as soon as the first fcpci.ko module is 'modprobe'd - I don't even get as far as modprobing the second. Any ideas on what's going on? Should I just back-up to an older version of the fcpci module

hello, got anybody succesfully setup asterisk with three avm fritz pci cards - using the howto described in http://www.quiss.org/caiviar/Two-Fritzcards-HOWTO i already have asterisk working with 2 cards, by when i add third card and compile driver ( see capiinit debug below ) asterisk freeze on capi initialization.... does anybody know how to solve this ? regards Marian ------------------

Hi list, i'm keen to move to Asterisk 1.6, so really need to update my system which is running Mandrake 9.2 although it has been solid for years, fo Fedora 8. I have a Fritz! card for ISDN BRI, I have installed the drivers/kernel drivers from ATrpms (http://dl.atrpms.net/all/fcpci-03.11.07-14.fc8.i386.rpm and http://dl.atrpms.net/all/fcpci-kmdl-2.6.23.14-115.fc8PAE-03.11.07-14.fc8.i686.rpm)

Hello, my name is Ikey Doherty. I am the founder of the SolusOS Linux Distribution. With SolusOS 2 we have decided to create our own base from scratch, using the PiSi package manager. After many repository revisions, it soon become apparant that GCC (4.7.2 in this instance) is dog-slow. Out of pure curiosity I attempted to rebuild packages using Clang. Clang had been pulled in as a dependency

Hi Folks, I have to setup a new server with a fritz-pci-ISDN-card inside. For it the fcpci-Packages from atrpm-repo is needed. Trying to install this package on a machine with the newest CentOS5-Plus Kernel I get an error message Missing Dependency: /boot/vmlinuz-2.6.18-8.1.14.el5 is needed by package fcpci-kmdl-2.6.18-8.1.14.el5 Okay -I have a vmlinuz-2.6.18-8.1.14.el5.centos.plus. Any

I've put my fire proof suit on ready to ask a question ;o) Redhat 9 Kernel 2.4.20-8 AVM Fritz PCI Problem 1... i have followed instructions from:- http://www.voip-info.org/wiki-Asterisk+AVM+Fritz+CAPI+Driver+Install http://www.voip-info.org/wiki-Asterisk+How+to+connect+with+CAPI (Plus many many other sites found via google over the last 16 hours) after modifying the makefile & defs.h,

Hi again! > I have excellent success with the tiny "fcpci" and chan_capi, which is > also working great with capi4hylafax. See > net-dialup/fcpci-0.1-r1 in gentoo (should not be difficult to use this > on other distros, but I have never done so). Do not confuse this with > the "fritzcapi"! I managed to install fcpci and it seems to run fine (capiinfo

If I do that, the modprobe doesn't find any module called fcpci and is looking for any module called hisax_fcpcipnp as it's the one install for the isdn fritz card. # capiinit modprobe: Can't locate module fcpci ERROR: failed to load driver fcpci Maybe, I should reinstall the fritz card drivers itselves? (however, I don't think so...)