similar to: BRI numbers

Good day all I added the music on hold entry in vpb.conf and commented out default line in musiconhold.conf. Asterisk starts up with the default mp3 but as soon as I remove it and add my mp3 it just doenst start up and gives a broken pipe error? Please Help or advice Thanks ALtus

Good day all We have a voicetronix openline4 card If someone calls in from the outside the pstn and into the system and hangsup asterisk does not deteck the hangup any Idea why please Help Altus

Good day all We have a quad bri card,installed on fedora core1,downloaded the latest bri-stuff that download asterisk 1.0.3 and zaptel 1.0.3 and libpri 1.0.3 All installed and working.BUT after 5min+ of talking it just drops the calls? Any reason why? Please help Thanks Altus

Good day all I had a look at the extensions.conf sorting http://www.voip-info.org/wiki-Asterisk+config+extensions.conf+sorting What I'm trying to do is route all my cellphone number threw a channel and all other calls threw the other 3 channels Cellphone numbers are 10 number,i.o.w XXXXXXXXXX. This is what I tried but it doesn't seem to work,please help Thanks Altus extensions.conf

Good day all I've installed a few systems with quad/octo bri cards On these systems incoming numbers are ether the full number,example 12345657 or ether the last 4 digits,example 7654 But for some reason the latest installation incoming numbers comes in as extension "s"?? Is this something to do with the telecoms provider or a asterisk config? Please Help ore advice Thanks Altus

Hello, Hacker I install VoiceTronix OpenSwitch 12 port PCI Telephone Card, and setting vpb.conf, extensions.conf following My problem is: When i dial to fxo(channel 9-12), it is ok, but when i continue press exten 102, the channel crach with error messages following exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872 Do i ignore some setting for VoiceTronix OpenSwitch12

Hi, I am using a voicetronix OpenLine4. I downloaded a recent asterisk CVS from voicetronix webpage but have had no luck to reduce echo on outgoing calls and for it not to crach on incoming calls. I dont think both problems are related though. Here is an output of what happens when a new call comes in and my voicetronix tries to pick it up and crashes asterisk: > vpb/1-1: Event

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

dear Hackers, i have a voicetronix Openswitch card, and i have been finding it very dificult to get it to work with asterisk. i intend to connect 8 ports to the PSTN and 4 as station ports. problem 1: On running asterisk all i get at first i get : event[9=>[11] station OFF hook] on vpb/1-12 even [12=>[11] loop drop on vpb/1-12 event [12=>[11] Tone detect:GRUNT event [2=>[11] Dial

Ron, VoiceTronix worked with me last week and backported the new chan_vpb that's in the current HEAD CVS tree to the 1.0 stable branch. So if you are using 0.7.2 or 0.9.0 you can go to the VoiceTronix website now (note that this is very new) and download an Asterisk package. When you download it there is an new chan_vpb.c that needs to be put in your asterisk source code tree. Also there

Hello all - I'm trying to get Asterisk working with an Openswitch/6 card with all ports set to FXO for PSTN in/out, and 10 SIP phones on the LAN with the Asterisk server. The SIP phones are working properly to dial one another, but I can't seem to get a call to go out to the PSTN through the voicetronix, and I similarly can't get incoming calls to the lines hooked up to the

hi there, i've been able to successfully run asterisk with the Voicetronix OpenLine4 card, it can accept calls and function normally. The only problem I'm experiencing so far is getting the card to outdial to a third party. What I'm trying to achieve is basically call bridging, where the caller dials in to asterisk, some IVR plays and then attempts to perform a "transfer"

Hi, Firstly it appears you are not passing the extension to be dialed to the Dial command, so the driver is dialing badly. It should be something like dial(vpb/1-2/102) since this is a line port. Admittedly the driver needs to check better that the number it is trying to dial is legit but it doesn't :) P. --- You Wrote --- From: "Jacky" <jacky.taiwan@msa.hinet.net>

Good day all I downloaded bristuff RFC3 and asterisk,zaptel,libpri versions 1.0.3 This is to install my quad bri card All installed well I coped over some old config files.All 4 ports are available,so that gives 8 open lines for incoming or outgoing,correct me of I'm rond The problem is,asterisk can only handle 2 calls at a time if there is 1 incoming(into pstn) and there someone already made

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

Good people, Please find attached a first shot at a driver for the Voicetronix OpenSwitch hardware. It does work (ish). After paying $900-odd for it I figured I might try to make it work with Asterisk (could never get enough documentation on Bayonne!) I have problems with the audio quality, and since am new to Asterisk, I could really do with some input. First is that because the

Attached is the updated driver, thanks to Mark's advice. It now does pretty good audio, although when you dial another channel via Asterisk you get some echo. This I have not been able to solve quite yet (using voicetronix echo cancelling doesn't seem to do it). If anyone can figure it out, would appreciate. Thanks P. Ps. Unpack inside asterisk code directory. Replaces your makefile

Hi there, I am trying to delay sending out DTMF from Voicetronix OpenLine4 to the CO line. The reason being is that Voicetronix sends out the DTMF too fast even before the line is fully established with the carrier. Usually when dialing an 8 digit number, only 7 digits are actually successfully heard by the carrier. Currently, my dial plan is: exten => _9.,1,Dial(vpb/1-1/${EXTEN:1}) Daniel

Before I start ... I know there's been a lot of talk over the last couple of days about the list being slow etc... I understand there were problems and that mail is starting to get through now. Just wondering - should I be surprised if something I sent 48 hours ago hasn't turned up at all? And something I sent about 6 hours ago still hasn't turned up (yet). I'm just curious