similar to: Reload crashes Asterisk ?

Hi, I've been having a little problem with my asterisk servers, I have 4 identical asterisk servers setup (same hardware, same OS, same config). Once in a while (once or twice a day) one of the server crashes on the cron job reload. But I realized this only happens on 3 of the 4 servers. Tried to spot the difference between that one server that wasn't crashing. The difference I found was

Hi, I am trying to post this again as I am getting no answers and the support@digium.com bounces... (I have searched the whole list and can't find the answer either) I have installed a 5 user license for G.729 and want to route calls through Asterisk from my G.729 phone to Cisco AS5300 also using G729. Both Cisco and the phone connect using this codec if I do not force the call to go

When I try to connect to * using a Cisco ATA 188 configured with a MGPC firmware (v3.1.1), I just keep getting this message every 30 seconds or so : May 10 10:08:21 NOTICE[7913]: chan_mgcp.c:1509 find_subchannel: Gateway '192.168.1.27' (and thus its endpoint '*') does not exist Using tcpdump, I have checked that the ATA188 (with IP 192.168.1.27 and port 2427) sends UDP packets to

Hi, I have licensed the digium G.729A codec. But for some reason incoming and outgoing calls will ALWAYS use G.711a. When I force my phone to only accept G.729 then an incoming call from ZAP goes straight to my voicemailbox as the phone doesn't accept the codec Asterisk wants, even if I force it in sip.conf. Is there anywhere else I need to look to tell ZAP to use G.729 preferrably ? The

I have a pretty basic Mandrake 10.2 w/KDE 3.2 and I installed Asterisk-1.0.1-2mdk. I installed the source of main and contrib from ftp, so at the install time I accepted all the packages needed to be installed too. The installation went smooth, but when I try to execute asterisk (#asterisk -vvv) I encounter few warnings I end with an error. At this point I didn't touch any conf file, I was

Hello list! I?m having an issue when reloading Asterisk, I?ve had this problem in Asterisk 1.6.1.6 so I upgrade to 1.6.2.1 version, but I still have the same error. For example, I send a "reload" in Asterisk CLI and this is the output: isb152*CLI> reload == Parsing '/etc/asterisk/extconfig.conf': == Found == Parsing '/etc/asterisk/manager.conf': == Found

Hi, My Asterisk CVS is apparently not doing much (other than keeping SIP & IAX2 registrations alive and doing some ZAP calls (without echo-cancellation), but slowly the memory is filling up, so much so that 100m virtual memory is used up within 12 hours and I have to restart the asterisk application every 48 hours to make sure I have enough memory... How can I help resolve this problem?

Hi, I would like to express my appreciation to your big efforts. I am enjoying Asterisk very much. My Asterisk works very well, but I encountered a segfault at voicemail after pressing # to end the recording. Please see the log below. My asterisk is running on RedHat 8. When booting the Asterisk, I found a WARNING around IAX, and it says "Unable to open IAX timing interface: No such

Hello folks, I'm trying to get an 8x8 DTA-310 running mgcp to work. I get no dialtone & can't get it to ring. My mgcp.conf says: ; ; MGCP Configuration for Asterisk ; [general] port = 2427 bindaddr = 0.0.0.0 [172.16.2.25] host = 172.16.2.25 context = default line => aaln/1 And here's the interesting bits of extensions.conf: [globals] ... TRUNK=H323/BYEXTENSION@pstn_gw ...

Hello all, I'm looking for some help to try to understand why my CPE doesn't work good with Asterisk in MGCP. Here is what I want to do : - Register a TECOM AH4021 on Asterisk in MGCP with the following profile in mgcp.Conf : [general] port = 2727 bindaddr = 10.95.20.1 disallow=all allow=g729 allow=alaw 020202020202] context=mgcp host=dynamic canreinvite=no dtmfmode=rfc2833 nat=yes

hi all I'm being spammed by these messages in the console (see below) and sound doesn't work with today's cvs. I rolled back a week, and it works fine. In addition to the sound problems, I had to enable inband dtmf squelch on the dilnk mgcp phones. if not, each pressed key was counted twice NOTICE[245776]: File chan_mgcp.c, Line 710 (mgcp_rtp_read): MGCP ast_dsp_process

> Hello all, > Can someone help me on the problem which I have on MGCP phone test . I test mgcp - asterisk- zap. But I got several NOTICE message from rtp.c. > NOTICE[20501]: File rtp.c, Line 221 (process_rfc3389): RFC3389 support > incomplete. Turn off on client if possible > > -- Endpoint 'aaln/1@VG101-1-1' observed '9' > NOTICE[20501]: File rtp.c,

When I do a 'asterisk -vvvvvc' I get following, but asterisk does NOT stay up: == Parsing '/etc/asterisk/asterisk.conf': Found == Parsing '/etc/asterisk/extconfig.conf': Found

Hello group I just update to the newest CVS now I'm not able to get asterisk to start. No error during the make or make install I did a make clean before the make;make install Any help would be great!!!! Here is the output asterisk -vvvvvgcd Parsing /etc/asterisk/asterisk.conf Parsing /etc/asterisk/extconfig.conf == Binding realtime_ext to mysql/realtime/extensions_table == Binding

Does anybody has the expirience configuring Asterisk with Cisco ATA 186 MGCP firmware ? I have Cisco software v3.1.1 atamgcp (Build 040629A) Asterisk 1.0-RC1 On ATA i only put domain test. mgcp.conf looks like this [test] host = 192.168.195.55 context = default line => aaln/2 line => aaln/1 Asterisk CLI shows this: Jul 31 16:05:40 WARNING[135449600]: chan_mgcp.c:485

Hello Thank for adding mail_log plugin in Dovecot POP3/IMAP server. But when I am use "mail_log" in pop3 secction Dovecot getting the following log message: ... Jan 26 15:34:11 rtr dovecot: pop3-login: Login: user=<gk2>, method=PLAIN, rip=8x.xx.xx.xx, lip=8x.xx.xx.xxx Jan 26 15:34:11 rtr dovecot: POP3(gk2): dlopen(/opt/dovecot/v1.0rc19/lib/dovecot/pop3/lib20_mail_log_plugin.so)

Hi, in following of a recent discussion I got to work on MGCP with the Cisco ATA186 again, and got it to work very nicely. However, there is a little thing with transfers I would like to get comments on: Call comes in from PSTN and goes to an ATA186 (MGCP) Call is answered and then, using flash, transferred to another extension If the extension is available, there can be an announcement and

Whenever I issue the reload command, asterisk crashes. Below is the output I get from (gdb) bt Any help is appreciated. *************************************************************** *CLI> reload == Parsing '/etc/asterisk/manager.conf': Found == Parsing '/etc/asterisk/enum.conf': Found == Parsing '/etc/asterisk/rtp.conf': Not found (No such file or

Looking at the error I tried moving chan_modem* out of the modules folder and asterisk started and its working again... Not sure what changed in the chan_modem_i4l.so but removing it from the folder fixed my problem. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Eric Hall Sent: Sunday, January 23, 2005

Hi everyone, I am running asterisk on red hat linux 9 box. The sound card is Intel 82801db AC' 97 audio and the module is i810_audio. It runs well with other applications like xmms and the standard tests deliver a sound . I have also tried to record voice and that works well too. 1-)Now when i run asterisk and i dial out an extension to play any sound there is none. The same thing