similar to: Bridging audio in cmd_dial() before connect completes?

Couldn't see the forrest for all the fascinating tree-like applications that are out there: For future reference, see: http://www.voip-info.org/wiki-Asterisk+call+parking :-) -----Original Message----- From: Kris Boutilier [mailto:Kris.Boutilier@scrd.bc.ca] Sent: August 11, 2004 1:10 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] Inband announcement of parking slot from

> -----Original Message----- > From: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com]On Behalf Of Gary Reuter > Sent: Thursday, August 11, 2005 12:59 PM > To: asterisk-users@lists.digium.com > Subject: Re: [Asterisk-Users] PRI dropped calls w/ asterisk dropped > betweenpstn & norstar > > > I poured over my logs most of

Unfortunatly no on both counts. The arrangement right now has: PSTN Trunks & Stations <-> Nortel Norstar#1 <-CT1-> Asterisk#1 <-IAX2-> Asterisk#2 <-CT1-> Nortel Nortstar#2 <-> Stations The Asterisk boxes provide Voicemail to their sites Norstars and intersite calls over IAX. Local Voicemail works flawlessly at each site but there have been reports of PSTN calls

I have a PRI link up and running between Asterisk and a Nortel Norstar MICS v4.1 . I'm having a problem getting the textual Caller Name across the link from Ast to Ns, however numeric Caller ID arrives and displays fine. From Ns to Ast both elements come through fine. I'm forcing dummy values for testing using: exten => s,1,SetCIDName(Test) exten => s,2,SetCallerID(1234561234)

I've noticed a problem with calls to Hangup when talking to my Norstars over channelised T-1 E&M trunk lines - it's been present since I started to fiddle with Asterisk last December and it's still present in 'Asterisk CVS-HEAD-08/13/04-10:37:13'. Specifically, when a call is connected to Asterisk from the Norstar DTI card to my T100p I get the following conditions

I'm trying to access feature codes remotely over a channelised T1 between a Norstar MICS (rev 4) and Asterisk. The timeslots are configured E&M and have been working fine under most circumstances except this one. There is mention of accessing the facility by calling Flash() from within extensions.conf, but I can't get it to work... Right now I can't tell if it's because

To answer my own question for the record: The relevant timing parameters in zaptel.h are #define ZT_MINPULSETIME (15 * 8) /* 15 ms minimum */ #define ZT_MAXPULSETIME (100 * 8) /* 150 ms maximum default, lowered to 100ms */ #define ZT_PULSETIMEOUT ((ZT_MAXPULSETIME / 8) + 50) And the pulse detecion loop that consumes these parameters begins at line 4866 of zaptel.c The

I'm having a problem with intersite calls over IAX2 being abruptly terminated. Nothing odd shows in any of the logs for Asterisk or the host. The only think I can think it might be is a lag-spike on the site to site connection. How sensitive is IAX2 to lost frames, lag spikes or large variations in jitter with the GSM codec and: bandwidth=low jitterbuffer=no trunkfreq=100 ; Raised from

> -----Original Message----- > From: Robert Goodyear [mailto:me@jrob.net] > Sent: Tuesday, March 22, 2005 1:21 PM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: [Asterisk-Users] Is there a way to get inserted into an LEC's > CLIDB? > > > Does anyone know if there's a service out there to -- for a fee -- > inject our DID into the

Inquiring (management) minds want to know. I'm assuming it's because 'it's funny how simple it really is to write a really decent voicemail system'? Kris Boutilier Information Systems Coordinator Sunshine Coast Regional District

Or perhaps how to configure and refer to two parallel IAX trunks with different codecs? I have a situation where I'm using G.729A as my IAX trunking codec. Now I need to push some short duration, low bitrate modem traffic over the link (a credit card terminal). Obviously the modem audio isn't going to survive the G.729 codec process intact, so for the times the device is used I'd like

I have a situation where I am receiving DID calls using Immediate Start Pulse signalling on a Loop Start trunk. The line terminates on a Newbridge Mainstreet 3624 channel bank, which provides battery etc. The channel is converted and routed to Asterisk. The lines are configured as follows: /etc/asterisk/zapata.conf ; Channels 1-24 service MainStreet 3624 channel bank context=infrom-did group=1

I'm trying to use Asterisk app_parkandannouce to build a global parking pool from within a couple of Norstar PBXes. Right now I can blind transfer calls into the parking lot, but the slot announcement relies on calling back the 'transferee' after the call is parked and I can't pass enough callerid data out from within the PBX to be able to route the call back in (ie. no PRI

Consider this dialplan fragment, where the call is being dialed into [macro-process-routing] over an iax2 channel from another (same build) Asterisk server: [macro-process-routing] ; This is the entrypoint of the debug call but is also refered to by Macro(process-routing) elsewhere in the dialplan ; XXX-NNN-6800 exten => _6800,1,Macro(6800-interceptor) ; This is matched when 8 is

Hello all, I updated from CVS 3 days ago and now my IAX2 gateway is dropping calls without warning. It happens right in the middle of a conversation with no pattern. I never had this Problem before and am usually talking 2-3 hours a day. Is their a bug? Should I rollback? Cheers, Paul Seniuk -------------- next part -------------- A non-text attachment was scrubbed... Name: Paul

Hello, After solving the other "low hanging fruit" audio issues in our Asterisk PBX, we are left with occasional cases of severe echo which we have not found a solution for yet. Our system: - Asterisk 1.2.0-beta1 - TE110P on a PRI - TDM04 and TDM40, but these are unrelated to current echo issues - Fedora core 3 - Echo canceller KB1 Most calls have minimal, acceptable echo levels. But

I have a set of analog DID lines coming into my Asterisk box, via a channel bank. The numbers in the DID bank route to various places, including voice lines of various staff. I am using the fax detection engine to intercept faxes accidentially sent to numbers on the DID bank and reroute them to a physical fax set up in the office. I would now like to preserve the received digits and pass them

> -----Original Message----- > From: Chris Shaw [mailto:chriss@watertech.com] > Sent: September 7, 2004 4:40 PM > To: Asterisk Users Mailing List - Non-Commercial Discussion > Subject: Re: [Asterisk-Users] Maximum tollerable lag/jitter for IAX2 > w/ojitterbuffer enabled? > {clip} > > If you can reproduce it, this smells like a bug... IAX runs over TCP and TCP >

Out of the blue i started receiving the following error on my PRI line which connects my asterisk server to a Norstar 0x32 key system. The asterisk zaptel.conf file was configure as follows and this config worked for 6 months until friday. Nothing was changed on either system prior to friday. here is teh zaptel.conf span=1,0,0,esf,b8zs bchan=1-23 dchan=24 span=2,0,0,esf,b8zs bchan=25-47 dchan=48

I've got a need to do something like the following: [foo-context] exten => _.,1,SetCIDNum(123) exten => _.,2,SetCIDName(XYZ) include => local include => tollfree But of course, this example won't work. The goal here is this: if a call ends up being handled by the "local" or "tollfree" contexts, I want those SetCID*** commands executed. Otherwise, I