similar to: Out Dial Problem

This was submitted to the Dev list last week, but there was no response, and perhaps it wasn't the right group. I am developing an application in which I need asterisk to pass on an incoming call to a separate IVR server. The problem is that asterisk appears to hang up while the IVR is playing back a sequence of recorded voice and systhesized voice prompts. My setup is: Analog line

Hi list, Just installed spandsp. In my limiting testing, I have an issue on a Philips fax machine (HFC21) directly connected to my * server through TDM400, reception with rxfax works fine, but txfax always fails. Below is a transcript of failed transmit. This is with asterisk-1.0.3 (with native moh patch but I don't think it is the source of the problem). I already tried libtiff 3.5.7,

Hello, I have problem to make SIP calls, i have asterisk + PC InterP4 + Digium TDM400P here is the content of the sip.conf: [SIP_PROVIDER] type=peer fromuser=testcomclient username=testcomclient secret=testr host=IP_SIP_PROVIDER ;dtmfmode=rfc2833 context=interne canreinvite=no ;allerid=Beer disallow=all allow=ulaw allow=gsm allow=g723.1 ; Asterisk only

Hi evereybody, I'm trying to use musiconhold during dial tones. But I only can call earing dial tones instead of music. Now will see my configuration files. AGI File(using AGI script to EXEC DIAL) print "EXEC Dial Zap/g2/numberc||m\"; $res=checkresult(); Extension.conf exten =>_numberb,1,Answer exten =>_numberb,2,SetMusicOnHold,default exten =>_numberb,3,AGI,dial.agi

Hi Everybody, I am trying to use SIP (Sipura 2000) to connect to Asterisk which then dials out a local number using the Digium E100P. We have purchased the G729 codec licenses from Digium and loaded them into Asterisk successfully. However, the call drops immediately after being answered with the debug error message saying something like: "channel.c:2646 ast_channel_bridge: Didn't get a

Hello, I have an Asterisk box with a TE410P connected to a PRI line and agents with X-Lite installed on the same LAN as the Asterisk server. Sometimes, when I make outbound calls it hangs up as soon as other party tries to picks up the call. Does someone ever experienced this situation? On X-Lite, only G711-ulaw is enabled and here is what i put in sip.conf: [4001] type=friend username=4001

Hi, Some calls I make trough my PSTN asterisk gateway just hangup after some minutes. Even if I'm using sip or iax. I have callprogress=no busydetect=no in my zapata.conf. Anyone help? Or tell me what to look at /var/log/asterisk/debug. I didn't find anything wrong. [endpoint]---iax or sip----[asterisk]----E&M----PSTN. As endpoint I had tested another asterisk box (with a FXS),

Hi all, I must admit that I am stuck. I have a TDM400P card with two FXS and two FXO modules which I had set up and configured so that it was working beautifully. The only problem was that occasionally it would get itself into a state where outgoing calls would simply be met with a very loud static. A reboot would fix this issue and everything would work fine for a while. Recently however,

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 i fixed wrong capi.conf (there was [controller1] after [interfaces]) now capi.conf is: ; ; CAPI config ; [general] nationalprefix=0 internationalprefix=00 rxgain=0.8 txgain=0.8 [interfaces] msn=855285,859609 incomingmsn=* controller=1,2,3,4 softdtmf=0 accountcode= context=local ;echosquelch=1 ;echocancel=yes ;echotail=64 ;callgroup=1

Hi everybody, Firstly I'm going to describe the scenario where I'm working. I use a E400P with Asterisk CVS-05/22/03-11:14:50, and I'm working with asterisk trow AGI scripts (Perl). The configuration of extension.conf is: exten =>_s,1,Answer exten =>_s,2,AGI,script.agi Inside the AGI script is call Dial application as follows: print "EXEC Dial

It seems consistant after dialing dozens of times that the call that doesn't go through is the one the gets the log message "No echocancellation requested" (chan_zap.c) and the "Scheduleing timer" (channel.c) in the middle of receiving the DTMF tones. I'm now using the T400P card last week very simular problems the the T100P (although I think I was actually loosing

I have a user who's system crashes on pri hangup request. Tried 1.4.19.1 and 1.4.20 as well as the latest libpri no change Progress is as follows...... < Supervisory frame: < SAPI: 00 C/R: 0 EA: 0 < TEI: 000 EA: 1 < Zero: 0 S: 0 01: 1 [ RR (receive ready) ] < N(R): 025 P/F: 1 < 0 bytes of data -- ACKing all packets from 24 to (but not including) 25 -- Since

Hello I have an interesting situaltion and not sure if I am doing something wrong or it is a BUG. I Installed Rhino Channel on T1 line and connected Analog Phone on Rhino's Zap Channels. If i pickup analog phone and hangup without dialing any number , I am getting extra ring after hangup and if i dial any digit than there is no ring on Analog phone after hangup. Log's looks like this

I seem to be having a problem with transcoding and/or agreeing on a valid codec. I am running a new image pulled from CVS at 1:30 PM CST. The issue occurs when I try to make a call to a toll-free number over sipphone.com. Here's what I see in the console: NOTICE[1259545280]: File channel.c, Line 1478 (ast_set_read_format): Unable to find a path from G729A to ULAW NOTICE[1259545280]: File

Hi, I'm trying to install a Junghanns quadbri for a few days but i stay with an asterisk error. (Everyone is busy/congested ) Asterisk is working with a Fritz PCbut from one year and now i want to add the quadbri. The quadbri card has been configured in NT mode and with no 100 ohms S/T termoination. (I'm not sure if the S/T parameter is correct) I have installed the bristuff package

Hello, I just CVS'd today and now I'm getting these errors when I call one grandstream phone to another both using 711U: NOTICE[1225991360]: File channel.c, Line 1476 (ast_set_read_format): Unable to find a path from ULAW to G723 NOTICE[1225991360]: File channel.c, Line 1446 (ast_set_write_format): Unable to find a path from G723 to ULAW NOTICE[1225991360]: File channel.c, Line 1476

My PBX seems to have just started showing wierd codec negotiation problems. I'm not all of a sudden getting this on certain phone numbers on my system: Feb 8 22:19:19 NOTICE[1125329728]: channel.c:1683 ast_set_read_format: Unable to find a path from ULAW to G729A Feb 8 22:19:19 NOTICE[1125329728]: channel.c:1650 ast_set_write_format: Unable to find a path from G729A to ULAW --

anyone has idea what problem can be here, something with codec but i have today CVS version and grandstream phone with 1.5.0 firmware.I try to change codec in phone and also in asterisk-sip.conf but the same. What can be problem ? tnx, Tomaz *CLI> -- Executing Dial("SIP/102-767c", "CAPI/2:5") in new stack -- Called 2:5 -- CAPI[contr1/2003002]/0 is making

Hi, Asterisk is new for me. I had a working configuration, but suddenly I can't call anymore with my voip provider. I am not aware that I changed anything in the configuration, but who knows. Can somebody explain me what is happening here? I changed username, password and number. -- Executing Dial("Zap/2-1",

Hello I have an interesting situaltion and not sure if I am doing something wrong or it is a BUG. I Installed Rhino Channel on T1 line and connected Analog Phone on Rhino's Zap Channels. If i pickup analog phone and hangup without dialing any number , I am getting extra ring after hangup and if i dial any digit than there is no ring on Analog phone after hangup. Log's looks like this