similar to: Onboard RAID Tyan Transport GT24 (Thunder K8SRE s2891)

We have been seeing failures with CentOS 4.4 i386 (not x86_64) running compute-intensive programs on Tyan K8SRE (S2891) Tymotherboards, running Opteron 265's. This motherboard is used in the Tyan barebones box GT24 (B2881). We have these boards populated with 8GB of RAM, consisting of mixed 2GB and 1GB sticks. The symptom is that CPU-bound programs (may or may not be related to floating

I am trying to install CentOS to a server that has a Tyan S2891 motherboard, 2 Opteron 875 Dual Cores and 2GB of RAM. I have been able trying to install over a network but the tg3 driver will not load. I then installed from a DVD and on rebooting after the installation I cannot get the network drivers to load and the RAID controller in the PCI slot is not available. It seems that when I do an

I've been planning to build a dual Opteron server for awhile. I'd like to get people's suggestions on a suitable motherboard. I've looked at the Tyan K8SE (S2892) and K8SRE (S2891) but would like to find more Linux-specific experiences with these boards. Some features I expect are at least 4 SATA (SATA-300?) ports, serial console support in the BIOS, USB 2.0 and IEEE-1394

Tyan has posted a lm_sensors config file for the Thunder K8SE S2892 at ftp://ftp.tyan.com/software/lms/lms_s2892.conf However when I ran the sensors command on my S2892 I was getting a readout for an adt7463 chip that wasn't referenced in the config file. I emailed Raphael Deng at Tyan asking him to confirm the manual edit needed to get sensors.conf to refer to the adt7463 chip. His

Hi, I'm trying to install 5.1 using the onboard LSI Symbios 53C1010, and I'm running into some trouble. When the computer first boots, the SCSI BIOS sees the three HDDs, but when I go to install, the installer hangs for a while at inserting the sym53c8xx driver and if I go over to the screen on F4 it shows that it is trying to scan the SCSI bus and is resetting all of the IDs. Once that

I had my eye on the Tyan dual-Opteron mobos for awhile. I tried to find a posting *anywhere* sharing experiences with these boards under Linux. No such luck. So placing myself under the heading "Where Angles Fear to Tread," I went ahead and built a system anyway. Here's what I've learned. The specs: Tyan Thunder K8SE S2892, BIOS 1.01 2x Opteron 270, 2Ghz Dual-Core, retail

Dear list, is anyone using a Tyan Thunder K8HM (S3892) with Xen? Or can recommand a (different) mainboard for: - dual dual-core opteron - about 16GB of RAM - two Gbit ports (for GNBD) - one (or more) SATA ports (system disk) - at last one PCI-X 133 slot. Thanks a lot. -- /"\ Goetz Bock at blacknet dot de -- secure mobile Linux everNETting \ / (c) 2006 Creative Commons,

https://bugs.freedesktop.org/show_bug.cgi?id=87934 Bug ID: 87934 Summary: nouveau errors on archlinux while running War Thunder native (not via steam) Product: Mesa Version: unspecified Hardware: x86-64 (AMD64) OS: Linux (All) Status: NEW Severity: normal Priority: medium

[This email is either empty or too large to be displayed at this time]

Hi Does anyone know how to get the PC speaker working with CentOS 5.1 & Xen 3.1? [root@gimbli ~]# uname -a Linux gimbli.softdux.com 2.6.18-53.1.13.el5xen #1 SMP Tue Feb 12 13:33:07 EST 2008 x86_64 x86_64 x86_64 GNU/Linux Xen version 3.1.0-53.1.13.el5 (mockbuild@) (gcc version 4.1.2 20070626 (Red Hat 4.1.2-14)) Tue Feb 12 12:55:35 EST 2008 Latest ChangeSet: unavailable -- Kind

I have a Supermicro SuperServer 6025B-3V with their X7DB3 mobo. It has an onboard Adaptec SAS RAID controller and has been configured as a RAID1 with two Seagate Cheetah 15k.4 disks. Original attempts at installing CentOS4.4 x86_64 appeared to load the aic94xx driver, but then reported something like "No hard drives found...". I grabbed the x86_64 aacraid driver disk from Adaptec

On 23/09/2019 13:10, Nicolas Kovacs wrote: > Hi, > > I have a CentOS 7 desktop client installed on an old Dell Optiplex > computer with an Intel video card integrated into the motherboard. The > card has a single VGA connector, and the 19" monitor is connected to it. > > I wonder how I could connect a video projector to this computer while > keeping the monitor, in a

Hi! I have a Asus P4C800 Deluxe motherboard with an onboard sound card. According to the mb. spec it's a ADI AD1985 SoundMAX 6-channel CODEC, AC'97 chipset. I'm running FreeBSD 5.1R and have device pcm in my kernconf. The only thing I see in dmesg output related to the card is pci0: <multimedia, audio> at device 31.5 (no driver attached) Full dmesg output available

Howdy all, Any recommendation as to the right way to config X. Last time I did was using X86Setup back in OpenBSD 2.7 days. What's the Xorg tool? How do I invoke it? Looks like I just need to fix the ranges, maybe they mean sync vert & horiz or something. Or should I be typing gdm instead of startx? Any advice? -below are some errors, infos, although the dmesg didn't pipe out

hi, I'm trying for some time to get a few games to run and it seems like Wine wants to use my onboard graphic card (ATI HD 3200) instead of my ATI HD 5670. The reason i think that is a) sometimes when launching Starcraft 2 it tells me that the driver for my graphics card HD3200 is out of date and that i should update, and b) i found this when i tried launching Natural Selection 2.: > Build

Hi, I have HP DL 180 G6 2U Rack Server with HP Smart Array Controller Card B110i Onboard SATA Controller Chipset. This server has 4 * 500 GB SATA HDD have configured RAID 1+0 and it shows Single Logical Drive of 940 GB Hard Disk in the RAID BIOS. Have created driver diskette using dd command to enable this controller card to the CentOS 5.6 x86_64 arch and it shows HP LOGICAL VOLUME of size 940 GB

http://bugs.freedesktop.org/show_bug.cgi?id=27387 Summary: nouveau crashes on GForce8200 (onboard) after start of xorg Product: xorg Version: unspecified Platform: x86 (IA32) OS/Version: Linux (All) Status: NEW Severity: normal Priority: medium Component: Driver/nouveau

Hi, I have a CentOS 7 desktop client installed on an old Dell Optiplex computer with an Intel video card integrated into the motherboard. The card has a single VGA connector, and the 19" monitor is connected to it. I wonder how I could connect a video projector to this computer while keeping the monitor, in a mirroring configuration, e. g. output is the same on the video projector and the

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 The new kernel-2.6.18-128.7.1.el5.i686 kernel breaks audio support on my onboard audio on an AMD Solo motherboard. 00:07.5 Multimedia audio controller: Advanced Micro Devices [AMD] AMD-8111 AC97 Audio (rev 03) After upgrading to the new kernel from kernel-2.6.18-128.4.1.el5.i686, I quickly noticed audio not working in Flash in firefox, then after

We've had a spate of these lately - about 3 or 4 boxes. I have a feeling we just got a bad run of motherboards, but thought I'd try to get some feedback. These are servers running with the Tyan Thunder K8SD (dual core AMD's, S2882 model). They have three onboard NIC's, two Broadcom gig NIC's BCM5704C's and an Intel 82551QM which is a 10/100 board. We use the