similar to: IAXY S100I noise

Hi, I recently acquired an iaxy device. Since I turned it on, the phone makes a strange noise. Is this normal? I'm not sure if there is some configuration that needs to be provisioned for it to quieten down. With my LinuxJack, the phone was dead until it the device was enabled by software, which is why I'm not sure if the behaviour of the iaxy is normal. I am a newbie with digium

Does anybody know why Digium S100I IAXy was discontinued? -- #Joseph

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04:

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Hi List, I have this good looking IAXy device... I have managed to provision it, i can see it registering to my asterisk box, however when I pick up the phone which is plugged in the IAXy I have no dialtone, nothing. Any ideas what might be going on? Cheers, Jean-Michel.

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a

I just bought an IAXy and have been using it with * and NuFone. Around once every 24-48 hours of operation (not off hook, just powered up), when I pick up the phone I hear loud static instead of dialtone. If there's an incoming call, the phone will ring and * CLI will show that it's trying iaxy, but when picking up--no answer to * and loud static. The incoming call goes to VM. Cycling

Hey Everyone, I recently purchased a few IAXy units for some testing, and have come across a some problems. One of them can be provisioned but will not ring the connected telephone. It also does not provide a dial tone when you pick up the phone. When a call is made to the IAXy one of the green lights on the board goes from a solid on state, to a flashing state that coincides with the

Hi all, I have a small query regarding ringing tones on an iaxy2. I have a customer who uses an iaxy to breakout to pstn via our *. However the customer complains that he gets no ringing tone whislt making calls, i just visited the site and can confirm this. I also have another customer who is presently in canada with an iaxy calling thru our * , he doesnt have this issue. I presume that the

I'm having some problems with a bunch of older IAXy devices. I have three S100I devices working. I can call each device from each other and everything works perfectly. When an inbound call comes in (from PSTN) and is routed to the device, it works perfectly as well. The problem is that when I place an outbound call (to PSTN), the remote party can hear me well, but I cannot hear the

Hi. I am trying to provision my newly purchased IAXy. I tried ./iaxyprov 192.168.0.4 myiaxy.conf It print a bunch of numbers on screen and then say Provisioning is 63 bytes Total packet is 77 bytes Got response back from '192.168..0.4' And that's it. I didnt get nothing else and there isnt any solid yellow light after minutes. I wonder if anyone could explain what I'm seeing? Is

hi, is there a possibility to provide german dialtones on an IAXy S100IPWRD? 'language=de' sets only the messages to german (voicemail, etc.) is there something like 'loadzone' as in /etc/zaptel.conf regards frank

I am not sure if this is the place for Digium user-to-user discussion, but... We have deployed many (20+) IAXy's in the field. At a couple of locations, the IAXy's have just stopped working after 1 or 2 days use. No lights go on, no DHCP lease is renewed as far as we can tell, and of course no dialtone and no registration with the server. Has anyone else experienced high failure rate

John Novack wrote: >And the only IAX2 box made is the Digium one, with it's current shortcomings ? >From reading through the archives, it seems there is currently no way to reset to factory default, no >written MAC address on an individual box, and some other instabilities requiring frequent resets. Yeah, there's the rub. Dunno if it's worth it, I'm willing to give it

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

The file used with a Digium IAXy device: "iax.conf" has the line: "port=5036" (I also use the "bindaddr=192.168.1.91" entry) but when Asterisk talks to the IAXy device it used port 4569 (from "tcpdump"). How are the port numbers assigned? What tells the IAXy which port to use. The IAXy provisioning file "iaxy.conf" file does not specify a port

The file used with a Digium IAXy device: "iax.conf" has the line: "port=5036" (I also use the "bindaddr=192.168.1.91" entry) but when Asterisk talks to the IAXy device it used port 4569 (from "tcpdump"). How are the port numbers assigned? What tells the IAXy which port to use. The IAXy provisioning file "iaxy.conf" file does not specify a port

Hi All, I have two old S100 units (the blue ones, not the newer black ones). I am trying to reset these to factory default using the following instructions, but it is not working. Does anyone have any other suggestions to reset this model of the adapter? Tried this: 1. Remove all of the cables, except for the power cable. 2. The factory reset button is next to the RJ45 jack. Press and hold the

Ok, I searched the lists and found no definitive answer. I'm assuming the IAXy has some primitive form of echo cancel, is there anyway to adjust this? Or any ideas on what to do instead. Here's the setup, this will not be a typical setup for our company however, well whatever. Anyway it looks like this: IAXy --> Netgear router --> Charter --> Level3 --> Asterisk --> VOIP or

Yesterday I was using one of the cheap Radio Shack phone polarity on various phone outlets in my house and ended up plugging it into my IAXY. While the regular phone jacks tested OK, the IAXY tested as being reverse polarity. The tester was plugged directly into the IAXY so there is no chance of this being caused by crossed wires. Is this something that is misconfigured on the IAXY, a hardware