similar to: no tones detected

I'm sorry if this has been answered before. I seem to remember reading a similar thread a while back, but for the life of me I can't find it (after 30 minutes of intensive googling). I have a voicetronix openline 4 card in an * server running CVS HEAD as of 1st March. Everything is working pretty much as as expected (with a little more echo than zaptel?). The question I have is

One of the suggestions I got for dealing with my analog FXO woes was to look into using a Voicetronix card instead of the Digium. They're more expensive but if it worked better it may be reasonable. They indicated they were compatable with the CVS HEAD version of *. Can someone share with me their experiences with Voicetronix OpenLine and/or OpenSwitch cards with *? I'm specifically

Hi all, Trying to get fax reception going using a voicetronix openline4 card, however, there are two issues (as far as I can see) (1) Currently the voicetronix world (cards, firmware, drivers, channel prog etc.) does not do fax tone detection. I have spoken to the voicetronix guys , understand what has to happen there and may do some hacking if I can resolve the second issue. Meanwhile, I

Hello all, I hope this is not off-topic, if it is please let me know. I'm currently playing with an Asterisk at home, in order to get to know it's ins and outs. Very very impressive indeed. I've got it hooked up to my home phone line via a Wildcard clone board (Intel modem with Ambient chipset), and it works like a charm. Zaptel picks up the card as a generic clone, and works with it

Any one has documented how-tos for making voicetronix openline 4 to work with Asterisk. I have been contacting Australian Digium resellers and Digium cards are not approved in Australia. So I suppose Australian users are interested into putting Voicetronix in use. Any expereience to share will be most appreciated. David Kwok -------------- next part -------------- A non-text attachment was

Hello, Hacker I install VoiceTronix OpenSwitch 12 port PCI Telephone Card, and setting vpb.conf, extensions.conf following My problem is: When i dial to fxo(channel 9-12), it is ok, but when i continue press exten 102, the channel crach with error messages following exception caught: VPBAPI_DIAL_INVALID_LEVEL, file: vpbdial.cpp line:872 Do i ignore some setting for VoiceTronix OpenSwitch12

Hello list, Hope you are all doing fine! I have stumbled over some piece of dialplan code in which apparently they were trying to avoid recording the DTMF tones in the wav file. It is really messy and I am not sure if this really works. So after a bit of research I found this comment ( https://community.asterisk.org/t/asterisk-dtmf-record/65040) in which it is said: *"Asterisk strips the

Skipped content of type multipart/alternative-------------- next part -------------- A non-text attachment was scrubbed... Name: Max Glucksmann (Fax del trabajo).vcf Type: text/x-vcard Size: 617 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20060118/b1b5e895/MaxGlucksmannFaxdeltrabajo.vcf

I have installed a 6VPCI card from voicetronix's but i can't get astersik to use it! Now looking at the loaded modules the chan_vpb is not loaded- so I assume that is why it is not working. Now I modified my vpb.conf file and extensions.conf, have I missed something Has anyone a installation guide as I am very new to this!! I have had asterisk working with SIP extensions. by dowloading

Does the voicetronix card work with Asterisk? -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of woody+asterisk@solutionsfirst.com.au Sent: Monday, February 02, 2004 11:06 PM To: asterisk-users@lists.digium.com Subject: RE: [Asterisk-Users] Pictures of new multiport FXO/FXS from digum > -----Original Message-----

Topology: PSTN<-T1 PRI->NEAX2400<-T1 PRI->Cisco 3825<-Ethernet-> Asterisk VoIP server When I make a call to a VoIP user from the PSTN, the call gets routed through the PBX, and Cisco. Because of that the DTMF tones are passed inband, which I can hear on the VoIP end of the call. However, I have one extension on asterisk set up so that I can check voice mail when away from my

Hi there, I am trying to delay sending out DTMF from Voicetronix OpenLine4 to the CO line. The reason being is that Voicetronix sends out the DTMF too fast even before the line is fully established with the carrier. Usually when dialing an 8 digit number, only 7 digits are actually successfully heard by the carrier. Currently, my dial plan is: exten => _9.,1,Dial(vpb/1-1/${EXTEN:1}) Daniel

Hi we've got Asterisk CVS-HEAD 18-Aug-04 (modified by Voicetronix as available on their site for use with the vpb driver) and an OpenLine4 (4xFXO). The same server also has two X100P. Calls on the Voicetronix card drop instantly when the called party picks up. The vpb driver reports that it detected a hangup (loop drop) yet there is no hangup when connecting the X100Ps or analog phones to

Hi list! ConfBridge dtmf_passthrough=no doesn't seem to have any effect. DTMF gets transmitted throughout the conference. I've tried Asterisk 10.7.1 from the official RPMs and 10.8.0 compiled from source. I've confirmed that it's disabled via the CLI "confbridge show profile user <profilename>". It's an all-SIP scenario with RFC2833 as the DTMF protocol.

Hi. I need help with my brand new Voicetronix OpenLine4 board that I installed into Asterisk. After building the Linux device driver and inserting the module, I modified the /usr/src/asterisk/channels/chan_vpb.c file to uncomment the US settings and comment out the Austrailian ones. I made the appropriate entries for routing in vpb.conf and extensions.conf.... All appears to be well, except

Got a wierd one that's reminding me of a problem mentioned in an earlier post but for the life of me, I can't find it. So... Inbound calls via a Voicetronix interface on my Asterisk box are being properly detected and routed to my dialplan as expected. It's a simple plan right now that rings a few internal Voicetronix and SIP stations. When the inbound line rings, it's ringing

Has anyone gotten the voicetronix boards to work with Asterisk, what would it take? Or does anyone know where I can get 4 ports or more fxs PCI cards that do work with asterisk? Brian J. Schrock Network Engineer, RHCE, CCNA Anistone Technologies Phone: 614-798-9106 FAX: 614-573-7165 6926 Avery Rd. Dublin, OH 43017

I'm looking to use Asterisk to replace my current PBX system. I'm in Australia so I need to use Austel approved equipment. My plan is roughly as follows: - Get a box with a suitable card and install Asterisk - Connect our existing PSTN lines to the Asterisk box - Get suitable softphones/ip phones to connect to the Asterisk system - Route all intra-office calls over our VPN - Route all

Hello, I would like to know if voicetronix card (specially openswitch6 and 12) can be used with asterisk. Is there any driver for this card? Best regards, Daniel -- Daniel ANDRE (mailto:dandre@iris-tech.fr) IRIS Technologies - http://www.iris-tech.com Serveur kwartz - http://www.kwartz.com