similar to: SPA-3000 as a regular Asterisk FXO device?

I am considering using Sipura-3000s as FXO devices for my * system. Has anyone tried them in that configuration? They interest me because they need no PCI slots and therefore no drivers. I would much prefer not to have any special kernel requirements for my system. /carmi

Since the 3000 has been out for a little while, has anyone done a review of the product? (couldn't find anything on google for wiki). Can the fxo and fxs ports be used as two independent channels? Is it really read for prime time? Etc. Rich

I'm trying to send a fax to my asterisk box, however shortly after connecting the fax machine reports a "communication error" and hangs up. Below is the error I get from RxFax: Fast carrier training failed Nothing is written to the file system as far as the tiff is concerned. Any ideas on how to fix this? Thanks ---- Sending Fax Machine: HP PSC 2000 Series 2210

After trying everything under the sun to get rid of echo on my X100P, I'm curious if anyone managed to solve the echo issues by switching to a SPA-3000? As well, if you have multiple SPA-3000's, can you create dial-out groups similar to the Dial(ZAP/g1) functionality? Thanks. -- Mike Benoit <ipso@snappymail.ca>

I recently upgraded from a few month old CVS version of Asterisk to v1.0.1, and dialing out through my SPA-3000 stopped working. Notice right after INVITE, in the old CVS version, it includes the number I'm trying to dial (8019596) which works fine, however in v1.0.1, it doesn't include the number and of course the dial fails. Did a config option change out from underneath me or

In my hunt to track down my echo issues, I tried disabling all echo cancellation, suppression, adaption, on my SPA-2000 (Advanced section of the config, under Line 1/2). Then calling from one local extension to another. (SPA-2000 Line1, to Line2 on the same device) I was pretty shocked with the results, the echo was HORRIBLE! I even tried 3 different analog phones. Now, once I turned the echo

I am trying to configure the FXO port on a Sipura-3000 for use with Asterisk. When I connect to the Sipura to dial out on the PSTN line connected to the Sipura's FXO port, it gives me the dialtone of the PSTN line and then I can hear the DTMF for the number I dialled beforehand. It does work but the customer perceives this delayed second DTMF feedback as "unprofessional" and the

This is my setup: SPA-2000 -> Asterisk -> X101P (x4) -> PSTN 3-way calling works fine if I use flash and dial just local extensions. Or even if I use flash and dial one local extension, and one remote party over the PSTN. However, as soon as I dial from my SPA-2000 out over the PSTN, and hit flash the call hangs-up about 50% of the time. The other 50% of the time it puts the call on

Hi All, Last week I started hearing a huge amount of local end echo on incomming calls. I am using a Sipura SPA-3000 as my FXO connected to an SBC POTS line. Echo cancellation is enabled in the SPA firmware. As a test I switched to a Digium X100 card the still lives in my server but the echo was about the same. I have both Polycom IP600 and SNOM 200 phone, which both hear the echo. I'm

Thanks Rich, I have an SPA-3000 laying around, so I will attempt to set it up in a little more conventional manner (although your method looks like a winner for a home test PBX). Would you mind posting or PM your current config to me, maybe screenshots if you PM. If I start with that it will take less time to get to the point where the SPA-3000 is a true FXO-FXS gateway for *. I will be happy to

Through my Asterisk server, I am trying to use IAXTel to dial 800-type numbers (yes, I know I can do the same thing with FWD and others via SIP, but I wanted to play with IAX a little). It appears I'm running into some sort of a codec mismatch or something because it's not working right. The SIP client is a SPA-3000. In iax.conf, I have something like the following: [General]

Voxilla.com has a great config wizard for the SPA-3000 and * http://voxilla.com/spa3kasterisk.php I took the output from this wizard and dumped it on my test box with an SPA 3000 (with some mods to match my * contexts) and everything worked great. Calls from the PSTN to the spa3000 are routed to dialplan #8 on the spa3000, which dials * Both the FXO and FXS port register with * The SPA3000 is

Anyone else got a Sipura 3000 in the UK? Apart from CID not working it also seems to not notice any of the line state changes on the PSTN when the remote party terminates the call. It only recognises the offhook signal which gets sent much later. Chris

Hi List, I hope this setup must be done by our astersik users.. I am using Sipura 3000 to receive PSTN calls and forward those calls to asterisk for voice processing and after that, I am transferring call to extension through FXS port on SPA 3000. Currently, media of call is trombone through asterisk. i.e achieving blind transfers on asterisk with SPA 3000. Is it possible to stop trombone

I've had an spa3k in service here at the house for a while now. After some initial wrangling, it's been working okay. I've had to reboot it a couple times and have noticed something rather annoying though. My setup is pretty simple and, dare I say, common. I have the SPA-3000 "inline" between my incoming POTS line and the internal house phone. It's setup to deliver

I am trying to get my xterm window under gnome to open with large fonts, with light green foreground and dark green background. I have the following .Xdefaults file contents: $ cat .Xdefaults ! This is a comment ;-) #ifdef COLOR *customization: -color #endif !! Let's cast a wide net, for any app supporting these ! Blink instead of beeping *visualBell: True *scrollTtyOutput: False

If I have a global variable in my dialplan and I change it, does that change immediately take affect for all calls that are active? Here is my situation. The company I work for has two office groups that share a building. The two offices are separate companies but support one another and want to be able to transfer calls as if they were all on the same phone system. Each company has 4

I have a situation where gnome console does not handle vt102 escape sequences properly and therefor need to employ xterm instead. When I run xterm from a gnome terminal window I am presented with an extremely small terminal window employing an almost unreadably small font. I have attempted to set the font size using xrdb and a custom .Xresources file. I can change the colour scheme. I can

Hi Guys. I've had a lay off from Asterisk for 12 months but I am starting to look into it again. I am not very Linux savvy and found it hard going the last time. I've started playing with it in the last 3 weeks and I have to admit to making more head way this time. The first problem I'm stuck on and I cant find a solution to is that sound files that I have recorded (be it by

Hello all, I have one Asterisk 1.4.21 system connected to a North American POTS line. Normally hangup detection works fine, and Asterisk hangs up properly if you are talking to a caller and they hang up; but occasionally a call comes in (typically from a US telemarketer) where the caller hangs up just as voicemail recording is starting, and you get a voicemail recording of dialtone (then