similar to: zaphfc hardware & sound trouble

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

I've this error How i can find the problem? Apr 23 12:24:43 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:47 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:24:48 WARNING[131081]: PRI: !! Got a UA, but i'm in state 1 Apr 23 12:24:53 WARNING[131081]: PRI: received TEI check request for TEI = 89 Apr 23 12:25:02 WARNING[131081]: PRI:

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

hi list. after my unsuccessfull experiences with mISDN i tried again to implement a zaphfc based solution. problem is: sound on calls via capi is stuttering/broken and therefore unuseable. my conf: - cel 1300, 256mb ram - avm b1 via capi connected to my outgoing ISDN - acer surf pci via zaphafc and crosslink cable with termination as internal bus - siemens gigaset 3035 as internal phone -

Hi, I have a partial working installation with zaphfc. Incoming call : For incoming call, seems work fine. But the sound is very bad with bounce short crashing sound. Same sound with echo cancel off or on. SDA work fine. Another problem, it's seems that's zaphfc don't reset correctly the line. I have one of my D channel how was busy even after stop communication. Outgoing call :

Hi list, Attempting to get an ISDN-BRI line connected using an HFC-S PCI card together with Asterisk v1.4.14 and Zaptel 1.4.7 on a Debian etch system, I find that I can't access the card's resources because the channels are always be busy. An attempt to call out results in the following CLI output: == Primary D-Channel on span 1 down == Primary D-Channel on span 2 down

I have some problems starting asterisk with a hfc card using zaphfc: [chan_zap.so]Mar 8 17:53:06 WARNING[2447]: loader.c:258 ast_load_resource: /usr/lib/asterisk/modules/chan_zap.so: undefined symbol: ast_retrieve_call_to_death Mar 8 17:53:06 WARNING[2447]: loader.c:391 load_modules: Loading module chan_zap.so failed! I'm using asterisk from debian/sid: Asterisk

Hi, my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this "normal"?: -------------------------------------------------- zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353, wanted 8 got 7), probably a buffer overrun. zaphfc: dropped audio (z1=2712, z2=2695, wanted 8 got 17, dropped 9). With Asterisk running (asterisk -vvvvvgc)

Has anyone had any success using the Florz patch for zaphfc ? I have a * system with 2 HFC cards which is working fine with 2 PTP ISDN lines however the users are complaining of crackles on the line which I am assuming is related to the IRQ issues raised by Florz. I have tried to use the patch but it errors trying to patch zaphfc.h Any help would be appreciated. Regards, Stuart -- No virus

I have the same problem in a box with 2 HFC-PCI, but i already remove the row in modprobe.conf and load the module manually. Both cards works fine Any idea ? Giordano -----Messaggio originale----- Da: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] Per conto di Julian J. M. Inviato: luned? 27 giugno 2005 12.04 A:

-----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Zoltan Szecsei Sent: zaterdag 16 juli 2005 12:54 To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [Asterisk-Users] Multiple ISDN BRI Units with Asterisk usingBristuff zaphfc in NT mode? >> Maybe this is rather a hardware question,

Hi list, Has anyone been able to get ISDN-BRI support to work reliably on Asterisk 1.4? If so, I'd love to know how you did it (hardware, distro, kernel, modules, versions, config files). I've tried to get it to work on a Debian etch system with an HFC-PCI card and the zaptel package (v1.4.7, also from xorcom.com), but with no luck: all three channels that are created when the

Hello all, if I try to call from one phone on the internal S0 to another on the same S0 using zaphfc, the bus is hung up. The called phone is ringing, but I can't talk from one phone to the other. The error I get is: -- Executing Dial("Zap/2-1", "ZAP/1/55|15|tr") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 1/55 -- Channel 0/1,

I've got a bit trouble with callerid and zaphfc cards. Basically zaphfc doesn't add the "0" in front of national numbers (haven't tried a international call yet). With chan_capi that allways worked fine, however i had to define the national and international prefixes in capi.conf. Is there something similar in zapata.conf ? Here is my zapata.conf: [channels]

I'm using bristuffed Asterisk with ISDN/ZAPHFC I have VERY ugly (outgoing) sound through ISDN/HFC if echocancel=yes in zapata.conf, but without echocancel I have bad (incoming) echo Through PSTN/FXO sound is ok with or without echocancel. I tried other echo cancellers (in zconfig.h) two times: ECHO_CAN_KB1 (this was default) ECHO_CAN_MARK2 ECHO_CAN_MG2 after any change I compiled (make

Hi, I'm trying to setup a small BRI ISDN <-> voip gateway. The ISDN card is based on Cologne chipset, so I try set it up with zaphfc. The versions i'm running: kernel-2.4.27 Asterisk 1.0.7-BRIstuffed-0.2.0-RC8e zaptel modules 1.0.7 zaphfc is from bristuff-0.2.0-RC8e When I'm doing the insmod on zaptel, zaphfc, zaprtc: Zapata Telephony Interface Registered on major 196 PCI:

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

Hi there, I've got a small problem with the zaphfc channel. No MSN of an any incoming call which comes trough the ISDN card (Acer ISDN, with HFC chipset and zaphfc driver) which will be forwarded to the SIP-Phone will be displayed. Always it will be shown "asterisk" an the Display. --- snip (zapata.conf) --- [channels] language=de switchtype = euroisdn signalling =

Hello, I've added a ZAPHFC card to my CAPI based system. Calls coming in via ZAPHFC do not forward the caller id to the SIP phones. Calls coming in via CAPI do forward the caller id to the SIP phones. Any and all help is greatly appreciated. The (hopefully relevant) conf file excerpts are: extensions.conf =============== exten => 807440,1,Answer exten => 807440,2,Noop exten =>

I have an ISDN card, Billion ISDN PCI Card I tried to use the ZAPHFC, I patched the kernel, I did anything (also followed reccomandation on use on Suse Linux Professional 9.2 --my box is) using bristuff last version. In the end I succesfully compile zaphfc, but I am not able to use the card (a lot of problem running zapcfg, a loto of problem starting asterisk saying about wrong anything (from