similar to: Has anyone tried using a Sipura-3000 as an FXO device for *?

I am trying to configure the FXO port on a Sipura-3000 for use with Asterisk. When I connect to the Sipura to dial out on the PSTN line connected to the Sipura's FXO port, it gives me the dialtone of the PSTN line and then I can hear the DTMF for the number I dialled beforehand. It does work but the customer perceives this delayed second DTMF feedback as "unprofessional" and the

Hi List, I hope this setup must be done by our astersik users.. I am using Sipura 3000 to receive PSTN calls and forward those calls to asterisk for voice processing and after that, I am transferring call to extension through FXS port on SPA 3000. Currently, media of call is trombone through asterisk. i.e achieving blind transfers on asterisk with SPA 3000. Is it possible to stop trombone

My SPA-3000 finally arrived and I'm trying to get the FXO port on it to work as if it was a X100P card as far as Asterisk is concerned. I have Asterisk dialing out over the SPA-3000 FXO port no problem. The issue I'm having problems with is having the SPA-3000 automatically forward all incoming PSTN calls to the Asterisk "mainmenu" context (or ext I guess). Currently the

Anyone else got a Sipura 3000 in the UK? Apart from CID not working it also seems to not notice any of the line state changes on the PSTN when the remote party terminates the call. It only recognises the offhook signal which gets sent much later. Chris

Anybody using a Sipura 3000 for FXO with Asterisk? Mine is working except for one small nit... When a call comes in from the PSTN, the Sipura answers it and then passes it on to Asterisk, which plays extension ring tone. I'd prefer for the POTS line to stay on-hook while the extension rings, and to only be answered by the Sipura when the extension answers. Has anybody made this work?

Since the 3000 has been out for a little while, has anyone done a review of the product? (couldn't find anything on google for wiki). Can the fxo and fxs ports be used as two independent channels? Is it really read for prime time? Etc. Rich

Hi All, I am using a Sipura SPA-3000 as an FXO gateway to bring calls in and out of Asterisk. I am using "PSTN Ring Thru Line 1" (on the "PSTN Line" tab) so Asterisk answers the call rather than the SPA-3000. It is all working perfectly except I can't get the SPA-3000 to pass caller ID to Asterisk. It passes "Display Name", "User ID" and any "PSTN

Does anyone have a Sipura 3k running, and using the FXO? I've got things working right, but if I try to toss a *67 in the dialplan, it seems the sipura is throwing a 403 forbidden back. For example: exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/${EXTEN:1} works fine exten => _91NXXNXXXXXX,3,Dial,SIP/sipura1pstn1/*67${EXTEN:1} does not (even if I toss a couple Ws in) I can't

I am located in the UK, and I am using Sipura spa-2000 adapters to connect analog phones to a voip network. The network connects to the PSTN as well via the Sipura spa-3000 adapter. I would like to provide surge protection for the spa-2000 and the spa-3000 adapters. 1. For spa-2000, fxs port: What is the maximum tip-to-ring voltage before damage to the the adapter occurs? 2. For spa-2000,

I have three Sipura 3000 FXO untis for incoming PSTN lines on a small pbx. There is an IVR to select the extension. The DTMF tones are not being sensed so the IVR does not work and incoming calls are not being answered. I have listed my sip.conf entries. Is there any solution to this? ;Sipura units [101] type=friend host=dynamic context=default secret=mysecret mailbox=101 dtmfmode=inband

Does anyone have any experience with the Audiocodes MP-108 FXO gateway? I'm looking to get one for incoming PSTN lines. In particular, does it pass caller ID information to Asterisk? I currently have a Mediatrix 1204 but Caller ID does not work, even though the specs say it does. All it sends are the names of the ports set up internally on the gateway (ie. "pstnline1" etc) when

Hello, I am very new to asterisk and voip in general and so far have managed to get the FXO card and a few sip phones working fine. My question is where does the Sipura SPA 2000 come in the picture? Can it be used as an extension (i.e FXS) ? Or is it to be used as a line (i.e FXO)? Or it can be used as both? My understanding is that its just like another ATA186. Is that true? I guess what I

If I have multiple Sipura 3000 device how can I dial out properly? I can receive call without any problem and that's working really well. Caller ID is shown and when someone call he get's the welcome message the same way I have it configure with the X100P card. I don't seem to have any echo problem with the Sipura 3000 (but I do with X100P cards) My main concern is for

Hello, Just want to tap the collective wisdom of this list as to experiences pertaining to the Handytone HT488 and the Sipura SPA-3000 adapters... Basically I'm looking for a FXO/FXS/LAN ATA and these two seems to be the top of the pick..Any comments and experiences esp. with Asterisk compatibility would be great, before I plonk in the bucks. TIA. /wai-sun

Hi all, I was wondering whether anybody here would help me clarify this minor issue please. If I have the following setup; Asterisk ------ Sipura SPA 3000 (fxo) --------- Pstn Line Would a call coming in on the pstn line be answered by the ATA or just get passed through to the * server (depending on dialplan) to handle? So basically, the caller does

Anyone know what I need to do to get the FXO port on the SPA 3000 to forward calls to Asterisk? My Asterisk is running on port 5061 and I set the dial plan on the device to forward to s@asteriskip:5061 but Asterisk is not picking it up. I can see on tcpdump traces that the Invite packets do go to through to the asterisk machine on port 5061, but it's not picking them up. sip debug does not

Hi Friends, I have successfully implemented Intercom, Voicemail and International dialing using Asterisk. Now I want to connect my PSTN Lines to Asterisk server. I have 3 PSTN number (lines) to connect to Asterisk. For this, I want to use Sipura SPA-2100. Is my decession is correct or not? Is there any disadvantages with this Sipura SPA-2100? Please tell me. Thank you. Regards, Chandramouli

I've a problem with inserting a "pause" and dialing additional numbers when going through Sipura-3000 exten => _12,1,Dial(SIP/4751724@pstn-5,30,D(wwwwww18)) D(wwww) doesn't work as it sends the DTMF tones right after FXS connects to FXO; though, I want insert a "pause" and send additional numbers after connection goes through FXO. Is it possible? -- #Joseph

I heard Sipura had really awesome documentation on the SPA-2000 and SPA-3000, but you have to email them for it. When I did, they said I had to get it from a reseller. It's been a while since I bought my units, I don't even remember where or who they were bought from. Can somebody email me the documentation for these devices? I'm quite interested in knowing what every one of their 200+

Hi there everyone! I've bought a Sipura SPA 3000, and succesfully connected it to my Mac, where I installed Asterisk 1.4.0. Both ports (FXO and FXS) are well configured). However, living in Brazil, I'd like to know if there are optimal settings to my PSTN that I should enter into the config of the device. I experience a little bit of echo on the FXO probably because I raised the gain of