similar to: Application Hangup not hanging up, possible dialplan cockup?

Hi everybody Could someone give a tip on how can I configure asterisk to use 2 ATA's 186 to communicate each other using SIP with asterisk. I know this most be a very simple task, however this is the very first aproach I have to asterisk. I set the following config but I don't get dial-tone when I off-hook the phone from any of the two ATAs. Can some one tell what I'm missing in

Hi all, -------- I have a Asterisk at a public Network (official IP address). In the local network I have isntalled a Snom 200 IP phone and in my home network (behind NAT) a Snom 100 device. I can dial the Snom200 device from my home location without any problems but the Snom200 can not dial me. It always gets a "we do not rely". I tried to forward the SIP Port (5060) UDP via UPnP

I can dial from 601 to a public number. The public number rings. I pickup and hear nothing, while on 601 it keeps ringing. (BTW, is it right to say "ringing" on the active phone?) The *CLI> doesn't show me anything useful: Executing Macro("SIP/601-8238", "dial-pstn|88097880|") in new stack Executing SetGlobalVar("SIP/601-8238",

Hi, I'm using the macro below in extensions.conf for most of my outbound calls. One issue with my current configuration is that when I make an outbound call it doesn't properly detect that my PSTN line (Zap/1) is busy with another call and then overflow to my outbound IAX connections. I think the root cause is that DIALSTATUS gets reported as BUSY. The debug output is below. My desired

I got two phones on an ATA-186 (601, 602) and two phones on the TDM22B (603, 604). I have two lines on the TDM22B. I cannot figure out some of the problems: 1. 601 dials via ZAP/3-1 to local phone number at PSTN: ringing pickup on PSTN (empty) still ringing in the phone set 601 2. call from PSTN back: 601 picks up ... everything works !!! No caller id shows up 3. For testing I have only one

When doing a vampire all my PC's are shown in the resulting log as being members of the Domain Users group and none of my "real users" are shown yet in Ldap all my users are shown with memberUid in the domain users group and no computers are shown eg: dn: cn=Domain Users,ou=Groups,<snip> objectClass: posixGroup objectClass: sambaGroupMapping gidNumber: 513 cn: Domain Users

On Mon, 30 Apr 2018, Marek Blaha wrote: > I can achieve the same error by > removing /usr/lib/python2.7/site-packages/urllib3/packages/ssl_match_hostname > and creating the directory in the same location instead. > So solution can be just removing this directory (or just renaming it): > > # mv /usr/lib/python2.7/site-packages/urllib3/packages/ssl_match_ > hostname >

I get more problems, I have not single i686 arch package installed yet 'yum update' somewhere along the lines decides and insists on pulling in plenty of i686 packages. All this without really telling why, then fails with 'multilib' problem. I cleaned/removed yum's cache, rebuilt rpm database. And while yum does that it shows lots of conflicts. It seems like a serious

Hello all, I'm new with rsync on Mac OS X. I'v tried to backup a project directory with the following command: rsync -avu "${source}" "${target}" The problem: files into bundles are copied though they were not modified. Furthermore, the permissions and attributes have been modified. NOTE: bundles are directory displayed as one file with one icon in the finder. Source

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, Here's a version I modified which grabs either a development or stable verision, and does a backup before updating from CVS. It also asks for addon's and cc. Leif Madsen did the original development and Mark released it. My changes does the minimum changes to previous version, to get what I need. It does the same version checking as the

How do you enable call waiting on sip phones? Ive looked and googled and can only find call waiting pstn phones butnot for sip. Is their a way of setting this up within the dailplan?

Hello Peter, The attached patch contains three small (although 2 of them are fundamental :) fixes for pxelinux 1. Alignment error when more than one initramfs are loaded using initrd - the alignment of the last disk is discarded in calculations but is ALWAYS present when the loading procedure is called. As a result - the second image (cpio) is not recognized. 2. On some platforms

I'm still trying to learn some parts of Asterisk, so sorry in advance for the dumb question! How do I set up an extension to dial out to the PSTN through my ZAP interfaces? I want the ability to have a ring group that will ring all of the phones in an office and then ring cell phones if nobody answers. I'm sure this is simple to do but I'm at a loss. I have tried the following

Hi I have been trying for a while to find a way to get an SMS send when I receive a voicemail into my asterisk system. I don't want to send an SMS if the caller doesn't leave a message. I have voicemail.conf set up to email and delete. 302 => 302,Website Sales,sip@example.com,,attach=yes|delete=yes However I can't seem to find a way to test is a message is left. I have tried

I am trying to set up a test kvm virtual machine on a core2 quad system. I have managed to thread my way through bridging eth0 and I have a CentOS-5.4 dvd iso prepared. Using virt-manager, when I try and add a new guest then I get the error reproduced below. Now, I know that I can 'fix' this by building a local mod via audit2allow and installing via semodule. However, I cannot seem to

Este no es el correo de Yanier ----- Original Message ----- From: <samba-request@lists.samba.org> To: <samba@lists.samba.org> Sent: Tuesday, May 10, 2005 2:02 PM Subject: samba Digest, Vol 29, Issue 13 > Send samba mailing list submissions to > samba@lists.samba.org > > To subscribe or unsubscribe via the World Wide Web, visit >

Este correo no es de yanier ----- Original Message ----- From: <samba-request@lists.samba.org> To: <samba@lists.samba.org> Sent: Wednesday, May 11, 2005 1:18 AM Subject: samba Digest, Vol 29, Issue 14 > Send samba mailing list submissions to > samba@lists.samba.org > > To subscribe or unsubscribe via the World Wide Web, visit >

Is it possible to have nested MySQL queries in extensions.conf? Ie, perform a query, grab a value, and then jump to another location in the dialplan and do another query based on that original value. I'm having problems with the result and fetchid's and I'm not sure if it's even possible to do this or not. Thanks, Doug. -------------- next part -------------- An HTML

I am trying to create a frequency distribution and I am a bit confused. Here are the commands I have entered: > data <- read.csv(file="40609_sortedfinal.csv",head=TRUE,sep=",") > NumberOfActionsByStatus = data$STATUS > NumberOfActionsByUser = data$ETS_LOGIN > NumberOfBidOffer = data$BID_OFFER > NumberOfActionsByUser.freq = table(NumberOfActionsByUser) >