similar to: Asterisk sees inbound call, but won't answer

Hi, I am a newbie in asterisk, i could compile it and run it with no problem on a RedHat 9. In the same box, i got a linejack and a phonejack cards and i downloaded the CVS driver from quicknet. This 2 card were working in a openh323 (openphone and pstn) project with gnugk on a RedHat 9. I am using the default samples, and i tried /dev/phone0 and /dev/phone1, but when i run asterisk, i get this

Hi, I am trying to get a prototype working based on Asterisk and Quicknet cards. I currently have to systems set up each with a LineJack card. I have the systems working, but can't get the voicemail demo to work properly. Messages to the user telephone set from the voicemail system are clear, but recordings left through the phone are distorted. Sounds like the audio has lots of echo and

Hi, I have been experimenting with Asterisk and the linejack card and have discovered the follow: 1) The linejack in FXS mode works well with asterisk as long as the format in the phone.conf is set to ulaw. With mode set to slinear, gsm recorded messages played by voicemail appear to be slightly choppy (sounds like a click at the end of each frame). 2) Using the configuration above, the

Hi all, Currently trying to get asterisk to dial out with an Internet Line Jack card, however, it does not use the pots line, only on the line it dials out of. This is similar to the previous thread/posting "Asterisk won't answer pstn ring", but I didn't find any follow up to get it working. My asterisk setup is like this: iptelephony:/etc/asterisk# cat phone.conf | grep -v

Greetings: We have been running a CVS HEAD version of asterisk from Mar 10, 2005 on ix86 (PIII-600) Linux 2.4.27 with ixj (chan_phone) hardware. In a hope of getting better 'chan_skinny' support (to attempt using a Cisco 7920 IP phone) I built asterisk 1.2.40 on this box. Initial tests verify that our previous dialplan is working (iax2 trunks, register sip phones, registering withour SER

I want * to answer the phone when call comes-in. I've enabled /dev/phone0 in phone.conf and created /dev/phone0 with a command: mknod /dev/phone0 c 100 0 Though, when I start * I get: Parsing '/etc/asterisk/phone.conf': Found Sep 12 00:18:42 WARNING[16384]: chan_phone.c:950 mkif: Unable to open '/dev/phone0' Sep 12 00:18:42 ERROR[16384]: chan_phone.c:1141 load_module: Unable

Hi, I'm having problems with setting up my ISA LineJack card on Linux machine... I've done everithing according to documentation available, by compiling the new ixj driver (v1.2.1), loading it, adding device node /dev/phone0 with major number 100 and minor number 0, adding aliases into the /etc/modules.conf: alias char-major-100 phonedev alias char-major-100-0 ixj and running depmod

I have a linejack and a phone jack in my asterisk server working well between the SIP phones and the phonejack. what I cannot get to work is the outbound linejack Phone/phone0 trunk line? how can I get a SIP or Phone/phone1 phonejack phone to dial 9 then outside number and pickup Phone/phone0 and dial it? right now it accepts a 95551212 but busy's on the last digit 2. no outside dial.

I cant seem to be able to figure this out. As much as I can tell it is a codec problem. I can dial out to 612@fwd.pulver.com and the "Call Me" test there rings my phone. However when the callee endpoint answers, there is a failure to translate: Outgoing Call for 612 612 is not a local user -- Called 612@fwdpulvercom No path to translate from SIP/fwdpulvercom-dd5a(2) to

dear list if I use EXEC in an agi script I get the following doing EXEC VoiceMailMain -- AGI Script Executing Application: (VoiceMailMain) Options: ((null)) May 21 04:25:10 WARNING[1209214400]: chan_phone.c:422 phone_read: Error reading: Resource temporarily unavailable May 21 04:25:10 WARNING[1209214400]: res_adsi.c:205 __adsi_transmit_messages: Un able to send CAS May 21 04:25:10

I have a Quicknet Linejack in /dev/phone0. My phone.conf is: [interfaces] mode=dialtone format=slinear echocancel=medium context=mayores device => /dev/phone0 Only I can mark 7 digits, soon asterisk tries dial automatically. I cannot mark 8 or more digits. 6 or less digits work ok. -------------- next part -------------- An HTML attachment was

Hi *, now for a long time i am trying to set the outgoing callerid, without luck. I am here in Germany, my asterisk has a pri interface connected to a PMX installed by Telekom. All telephone calls are preselected to EcoVoice. I am using asterisk 1.2.7.1, zaptel 1.2.5 and libpri 1.2.2. A week ago we tried with a device able to simulate a telephone system so send out a callerid, and that

At the CLI, should the command "show channels" list the configured devices that may be used for calls? Or, is that command simply a way of viewing the channels on a T1/E1 if you have that type of interface? If the latter, is there an equiv. command to list the single FXO interfaces? If the answer is yes, all configured devices should have something in channels, how do you map a

Hello All... I have searched in the archive and also followed Zara's instruction on getting incoming calls to work with Asterisk...but I still can't get Asterisk to answer incoming call on Linejack's LINE port. I attached a phone set to the PHONE port, and telco line to the LINE port on the Linejack(ISA) card. I have downloaded, compiled and installed the newest driver for

I have a Quicknet Linejack. Actually, I want to make a standalone(no internet connections) call to my asterisk box running GNU/Linux. When I call the system it says: -- Executing BackGround("Phone/phone0", "demo-congrats") in new stack NOTICE[14349]: File channel.c, Line 1212 (ast_set_write_format): Unable to find a path from 2 to 1 WARNING[14349]: File file.c, Line 553

i'm having this error message when trying to run the agents-feature Sep 2 17:37:40 WARNING[10445]: pbx.c:1645 pbx_extension_helper: No application 'AgentsLogin' for extension (from-internal, 28, 1) while chan_agent.so is beeing loaded i still don't seem to have access to the commands like agentlogin or agentcallbacklogin. my agents.conf and queues.conf are configured correctly

I'm trying to somewhat reduce the security risk of Asterisk, by loading less modules. In my installation I use SIP and IAX2 for incoming calls, and that's it. No voicemail, no call parking, it just plays back voice clips. I can remove /etc/asterisk/modules.conf modules one by one: ------------------------------------ [modules] autoload=yes noload => pbx_gtkconsole.so noload =>

My thanks for previous help on fixing IXJ issues in 1.2.40; I now have problems with a just-built 1.4.35 on the same host: [Aug 18 17:26:48] WARNING[27209]: app_dial.c:1298 dial_exec_full: Unable to create channel of type 'Phone' (cause 0 - Unknown) == Everyone is busy/congested at this time (1:0/0/1) O/S: Linux 2.4.27; IXJ driver for Linux Rev. 3.5, gcc 3.01 I applied the patch for

Hi folks, First off all, I'm new to asterisk. I'd like to make a basic installation of * with a Linejack, as recommended in this mailing list, I downloaded and setup successfuly the pwlib, openh323 lib, asterisk and chan_323. I have made little changes to default configuration files packed with asterisk and I managed to call with the telephone plugged in my Linejack a friend

Hi :) I've had all this working before, but I'm revisiting it, and in short, I currently have huge problems receiving incoming calls. I've been trying with both FWD and voiptalk.org. I'm running CVS HEAD of asterisk, zaptel and libpri as of yesterday afternoon. Would someone mind helping? :) My machine is 10.0.0.1 on my LAN, but the ADSL router has 10.0.0.1 set as the 'DMZ