similar to: No Compatible codecs? Got license

Hi, I am trying to post this again as I am getting no answers and the support@digium.com bounces... (I have searched the whole list and can't find the answer either) I have installed a 5 user license for G.729 and want to route calls through Asterisk from my G.729 phone to Cisco AS5300 also using G729. Both Cisco and the phone connect using this codec if I do not force the call to go

Hi, I have licensed the digium G.729A codec. But for some reason incoming and outgoing calls will ALWAYS use G.711a. When I force my phone to only accept G.729 then an incoming call from ZAP goes straight to my voicemailbox as the phone doesn't accept the codec Asterisk wants, even if I force it in sip.conf. Is there anywhere else I need to look to tell ZAP to use G.729 preferrably ? The

Hi, I am trying to replace my Cisco 5300 gateway with my new Zap TE405P card. Incoming calls and outgoing calls between my cisco and my SIP phone works fine on G.729. Recording messages in the asterisk voice-mailbox also works fine from both my SIP phone as well as PSTN -> Cisco -> Asterisk. I have licensed the digium G.729A codec. When I connect my ISDN PRI to my Zap card and I call

Hi folks, In an effort to save bandwidth (our 7905s run over a WAN) we've switched from ulaw to g729a. We purchased 4 licenses from Digium (4 SIP clients, low call volume), and they seem to have been accepted: [codec_g729a.so] => (Annex A/B (floating point) G.729/PCM16 Codec Translator) == G.729 Host-ID: 07:53:aa:d3:e2:f2:bd:cc:27:60:9d:5f:da:eb:5d:e9:6e:09:a1:4e == Found license

List, I purchased 2 g729 licenses but I can't get it to answer a g729 call from a cisco router with a vwic card. In the debug output below you will see that asterisk thinks it only supports: (gsm|ulaw|alaw|h263) when it should support g729 according to the config also listed below. The real odd thing is I can place g729 calls to the router, just not from the router to *. Anyone have any

Firstly, I'm running Asterisk 1.4.4 on Solaris 10. I have several different internal SIP phones all sharing a single IAX2 VoIP channel. PHONES |------------- <SIP/uLAW> --------------| ASTERISK |-------------- <IAX2/g729> ------------|VoIP/ISP The g729 codec has been registered successfully and appears to be detected by Asterisk (NOTE: I have changed what I thought might have

Hi, I purchased a G.729 1 channel codec license from digium. And installed as per the documentation. Then configured the sip.conf to use the new codec. For that, I am added the following entries in sip.conf (via web interface, as i am using asterisknow 1.5) disallow=all allow=g729 allow=ulaw allow=alaw allow=gsm After that, when try to call through the PSTN line I can hear the voice of

Original Post ---------------- I have an Asterisk related problem with mutualphone. I can connect to any number with any softphone that I am using (iaxcomm, SJPhone, and a few others). Also I have a Grandstream BT 101. But I cannot call (via Asterisk) to mutualphone destinations. Other destinations go fine. A working phone call (e.g. from iaxcomm) gives the following on the console: --

Hi Sir, We have integrated Skype with Asterisk (skype user id:- rexesbposolutions). Each call which is coming to skype account is getting transfered to Asterisk Queue. It has following two cases: case 1: When we call from normal skype account to skype account (rexesbposolutions), everything is working fine. case 2: This skype account (rexesbposolutions) has been assigned with a online virtual

I have a pretty basic Mandrake 10.2 w/KDE 3.2 and I installed Asterisk-1.0.1-2mdk. I installed the source of main and contrib from ftp, so at the install time I accepted all the packages needed to be installed too. The installation went smooth, but when I try to execute asterisk (#asterisk -vvv) I encounter few warnings I end with an error. At this point I didn't touch any conf file, I was

hi, I'm currently trying to use Speex with Asterisk from my OpenH.323 client. It seems to mismatch the codecs, below is my log from Asterisk. My Openh323 client crashes in responding to a Speex request for bits per frame. I'm guessing it either isn't running the codec correctly or doesn't support the same subset of speex codecs as openh323. (I'm using speex-1.0.1 with

Hello, I have that problem with codec G729. Please can somebody help me! WARNING[16384]: File codec_g729b.c, Line 413 (load_module): Unable to initialize va stuff: -1 == Detected 4 licensed G.729 transcoders WARNING[16384]: File translate.c, Line 219 (calc_cost): Translator 'g729tolinb' does not produce sample frames. == Registered translator 'g729tolinb' from format G729A to

Hello, Can somebody tell me what does it means ? I just installed my codec g729 with two channels. [codec_g729b.so] => (Annex B (floating point) G.729/PCM16 Codec Translator) == Detected 2 licensed G.729 transcoders WARNING[16384]: File translate.c, Line 219 (calc_cost): Translator 'g729tolinb' does not produce sample frames. == Registered translator 'g729tolinb' from

Hi guys, Just installed G.729 (from digium) codec and after starting asterisk getting the following warning: [codec_g729b.so] => (Annex B (floating point) G.729/PCM16 Codec Translator) WARNING[1082809536]: File asterisk.c, Line 234 (listener): Select retured error: Interrupted system call WARNING[1082809536]: File asterisk.c, Line 234 (listener): Select retured error: Interrupted system call

Hi, I have a new phone in our IP phone network: Planet VIP-101T. When calling from that Planet phone to anybody, everthing is fine. But when calling from anybody to that Planet phone, I get a mashine gun noise and the following msg in asterisk log: NOTICE[262161]: File channel.c, Line 1091 (ast_read): Dropping incompatible voice frame on H323:0 of format SLINR since our native format has

Starting up the asterisk using asterisk -vvvc i get this error is this normal and i purchased license for g729 today? [codec_g729b.so] => (Annex B (floating point) G.729/PCM16 Codec Translator) Jan 21 17:31:58 WARNING[1082805040]: asterisk.c:255 listener: Select retured error: Interrupted system call Jan 21 17:31:58 WARNING[1082805040]: asterisk.c:255 listener: Select retured error:

Dear i have buy two license of G729 codec and i have install/registered as documented but after i start "Asterisk -vvvcng" i notice this warning and if i made call the CLI say "No compatible codec!" How can i solve this problem? Thanks in advance Dimitri ------------------------------------------ [app_datetime.so] => (Date and Time) == Registered application

Where do these strange noises come from? <http://www.tobiasjonsson.se/asterisk/recorded-sound.wav> First sound in the recording above is from a ISDN (EuroISDN) connection thru chan_modem in Asterisk. Second sound is recorded from a SIP soft phone to the same RxFAX(), which now sounds all right. I have talked to Steve Underwood who says I am the first to report this problem and he thinks the

Hi, I write to this list, because I didn't find anything on the net. I installed asterisk using bristuff-0.0.2 without any errors, but when I start asterisk with "asterisk -vvvc" I get following error: [codec_ilbc.so] => (iLBC/PCM16 (signed linear) Codec Translator) == Registered translator 'ilbctolin' from format ILBC to SLINR, cost 127 Segmentation fault Removing

hi michael, here are the core dumps. only kphone works when 0.5.5 and * cvs. audiocodes and msn messenger all cause seg faults when calling ccm thru * (or vice-versa) ~kelvin [chan_oh323.so] => (OpenH323 Channel Driver) == Parsing '/etc/asterisk/rtp.conf': Found == Parsing '/etc/asterisk/oh323.conf': Found 0:00.004 OpenH323 Wrapper OpenH323 Wrapper