similar to: SIP client to IAXTel 800/888/877/866 dialing thru Asterisk

I don't see anything on the Wiki or in the documentation about disabling this feature.

I created an account at IAXTEL.com to route 1-700-XXX-XXXX calls through. IAXTEL.com gave me a number (example) of 700-555-6226. I have made the following changes to my: /etc/asterisk/extensions.conf: [iaxtel700] exten => _81700XXXXXXX,1,Dial(IAX2/myusername:mypassword@iaxtel.com/${EXTEN:1}) exten => _81800NXXXXXX,1,Dial(IAX2/myusername:mypassword@iaxtel.com/${EXTEN:1})

I finally got around to signing up with Iaxtel and Free World Dialup... the price was right, as far as that goes! I've gotten and placed calls via FWD just fine. But I can't seem to get registered, or stay registered, with Iaxtel. My logs show the story; at startup I see: Jan 20 07:14:44 VERBOSE[14121]: -- Registered to '65.39.205.121', who sees us as ... yada yada... As

I'm trying to make a call from an IAXPhone client - through the * PBX to an 888 number using the IAXTel link. I'm using the basic conf files for extensions and iax. I get successfully connected (at the "Attempting native bridge" line of the output) and am then able to talk both ways for 20 to 30 seconds and then the IAX phone appears off line. If I wait on the PSTN line for

Hi all, I spent most of the last weekend testing and trying to diagnose some mostly incoming call issues. I'll start with the easy one in the hopes it might have a positive impact on the others. First- I have an account with IAXTel. I can place calls to other IAXTel subscribers and also through IAXTel to landline toll free numbers and all works great. iax2 show registry shows I am

G'day list, I am getting a lot[1] of traffic on my Internet link, ICMP messages from 69.73.19.178 telling me UDP port 5036 is unreachable (this IP address belongs to iaxtel.org). I see from the wiki that IAXtel supports only IAX2 from December 2003. Fine, however it looks like my * still wants to try and register using IAX1, and I can't find how to turn this off. This situation is

Hi all, Below is what I did to run Asterisk in pass-thru mode: sip.conf: [general] disallow=all allow=ulaw canreinvite=yes For each channel, canreinvite=yes is enabled. No dial command has 't' option. However, it seems that Asterisk still stay in the media path and bridge the 2 end points. Am I missing something??? sip*CLI> show channels Channel (Context Extension

Hi there, do I have a local problem, or is registration at IAXTEL impossible at the moment? "iax2 show registry" permanently shows a TIMEOUT for 69.73.19.178. Philipp

I am considering using Sipura-3000s as FXO devices for my * system. Has anyone tried them in that configuration? They interest me because they need no PCI slots and therefore no drivers. I would much prefer not to have any special kernel requirements for my system. /carmi

I've searched WIKI and Archives but nothing. Im getting: -- Called username:password@iaxtel.com/1800somenumber@iaxtel Jun 21 17:04:12 WARNING[1158883520]: chan_iax2.c:5097 socket_read: Call rejected by 69.73.19.178: Unable to negotiate codec -- Hungup 'IAX2[Iaxtel]/8' == No one is available to answer at this time -- Executing Hangup("SIP/104-b8eb", "")

When I try to call iaxtel it goes to codec ADPCM even though I have define in iax.conf gsm Call accepted by 69.73.19.178 (format ADPCM) -- Format for call is ADPCM My settings: [general] port=4569 register => xxxx:xxxx@iaxtel.com bandwidth=high jitterbuffer=no tos=lowdelay [voipjet] type=peer host= xxx.xxx.xxx.xx secret= xxx auth=md5 notransfer=yes context=incoming disallow=all ;

Since the 3000 has been out for a little while, has anyone done a review of the product? (couldn't find anything on google for wiki). Can the fxo and fxs ports be used as two independent channels? Is it really read for prime time? Etc. Rich

I didn't get any response at all to my last "request for status" on IAXTEL. So, when this happens, I attribute it to one of a number of things: 1. No-one knows. 2. No-one cares. 3. Everyone knows, but are too busy to reply. At any rate, my investigative side kicks in and I began searching thru the digest's I've gotten, looking for references to IAXTEL. Mostly it is

Hello, I have a problem with connecting a Digium X100P card to a Brazilian analog line. Can somebody help me out with this problem? My /etc/zaptel.conf is loadzone=br defaultzone=br fxsks=1 My /etc/asterisk/indications.conf [general] country=br [br] description = Brazil ringcadance = 1000,4000 dial = 425 busy = 425/250,0/250 ring = 425/1000,0/4000 congestion =

After battling for days trying to figure out what was wrong with my iax.conf it was determined that I do not have any inkeys set on the digium server. Now whether that is something new or just in a few cases I am not sure. Messing around and reading on IRC and the mailing list I could get certain things to work and then break other things. Now I can dial a IAXTEL number, 800 number and FWD

I'd like to announce the time when people call and hit my voice-menu context, but the complaint is that the time announcement isn't interruptable. Is there any way to make SayUnixTime interruptable? -- PhoneBoy

Yes, After call transfer,I don't want to be media go through Asterisk. Is it possible ? Thanks, Karun. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com]On Behalf Of Dameon D. Welch-Abernathy Sent: Thursday, August 12, 2004 12:07 PM To: asterisk-users@lists.digium.com Subject: Re: [Asterisk-Users] Blind Call Transfer using

I have some stuck channels that I think I'm going to have to bounce Asterisk to get rid of, but am curious to know what they are and how they've managed to accumulate. The show up with a channel identifier of '(None)' as in the output below, and do not show up in the soft hangup list, and so can't be cleared by that method. Here is the output from iax2 show channels:

I've been using * CVS code from May of this year and was able to connect to iConnectHere and receive calls with * being behind NAT. Now that I've upgraded to 1.0 RC1, this no longer works. I've tried setting nat=yes in places, externip, et al with no success .. even though the code I was running from back then worked without that. Any suggestions? BTW, I've gotten DTMF from

Anyone else got a Sipura 3000 in the UK? Apart from CID not working it also seems to not notice any of the line state changes on the PSTN when the remote party terminates the call. It only recognises the offhook signal which gets sent much later. Chris